• Electrical & Electronic Materials
• /
• v.7 no.4
• /
• pp.317-324
• /
• 1994

In this study, new preparation method of LiCoO$_{2}$ was applied to develop cathode active material for Li rechargeable cell, and followed by X-ray diffraction analysis, electrochemical properties and initial charge/discharge characteristics as function of current density. HC8A72- and CC9A24-LiCoO$_{2}$ were prepared by heating treatment of the mixture of LiOH H$_{2}$O/CoCO$_{3}$(1:1 mole ratio) and the mixture of Li$_{2}$CO$_{3}$/CoCO$_{3}$(1:2 mole ratio) at 850 and 900.deg. C, respectively. Two prepared LiCoO$_{2}$s were identified as same structure by X-ray diffraction analysis. a and c lattice constant were 2.816.angs. and 14.046.angs., respectively. The electrochemical potential of CFM-LiCoO$_{2}$(Cyprus Foote Mineral Co.'s product), HC8A72-LiCoO$_{2}$ and CC9A24 LiCoO$_{2}$ electrode were approximately between 3.32V and 3.42V vs. Li/Li reference electrode. Stable cycling behavior was obtained during the cyclic voltammetry of LiCoO$_{2}$ electrode. According as scan rate increases, cathodic capacity decreases, but redox coulombic efficiency was about 100% at potential range between 3.6V and 4.2V vs. Li/Li reference electrode. Cathodic capacity of HC8A72-LiCoO$_{2}$ was 32% higher than that of CFM-LiCoO$_{2}$ and that of CC9A24-LiCoO$_{2}$ was 47% lower than that of CFM-LiCoO$_{2}$ at 130th cycle in the condition of lmV/sec scan rate. Constant cur-rent charge/discharge characteristics of LiCoO$_{2}$/Li cell showed increasing Ah efficiency with initial charge/discharge cycle. Specific discharge capacities of CFM and HC8A72-LiCoO$_{2}$ cathode active materials were about 93mAh/g correspondent to 34% of theretical value, 110mAh/g correspondent to 40% of theretical value, respectively. In the view of reversibility, HC8A72-LiCoO$_{2}$ was also more excellent than CFM- and CC9A24-LiCoO$_{2}$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.768-774
• /
• 2010

A parametric study is conducted for the segmented arc plasma torch with the input power and current of 0.4 MW and 300 A, respectively. For this purpose, we use the analytical relationship equations between plasma temperature, inner diameter (R) and length (L) of the torch constrictor at the given input power and current conditions based on the arc channel model. The results reveal that arc plasma temperatures show non-linear behavior or absence corresponding to the variations of L and R when their values become larger than 1.25 m and 7.5 mm, respectively. For L < 1.25 m and R < 7.5 mm, however, they can increase monotonically as L increase or R decrease when one of both parameters is fixed. From these parametric study results, optimum ranges of R and L are suggested as $5.5mm{\leq}R{\leq}7.0mm$ and $0.5m{\leq}L{\leq}1.0m$ for 0.4 MW class segmented arc plasma torch, under which stable arc plasma with the temperatures of ~15,000 K can be achived at the input currents of ~300 A.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.12 no.2
• /
• pp.70-80
• /
• 2000

Princeton Ocean Model (POM) is modified to construct a three-dimensional, semi-implicit hydro¬dynamic model with a wetting-and-drying scheme. The model employs semi-implicit treatment of the barotropic pressure gradient terms and the vertical mixing terms in the momentum equations, and the velocity divergence term in the vertically-integrated continuity equation. Such treatment removes the external mode and thus the mode splitting scheme in POM, allowing the semi-implicit model to use a larger time step. Applied to hypothetical systems, both the semi-implicit model and POM give nearly the same results. The semi-implicit model, however, runs approximately 4.4 times faster than POM showing its improved computational efficiency. Applied to a hypothetical system with intertidal flats, POM employing the mode splitting scheme produces noises at the intertidal flats, that propagate into the main channel resulting in unstable current velocities. Despite its larger time step, the semi-implicit model gives stable current velocities both at the intertidal flats and main channel. The semi-implicit model when applied to Kyeonggi Bay gives a good reproduction of the observed tides and tidal currents throughout the modeling domain, demonstrating its prototype applicability.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.4
• /
• pp.462-466
• /
• 2010

The purpose of this study is to evaluate the safety of a wire connector fabricated for the effective installation of a lighting fixture including its contact resistance, insulation resistance, withstanding voltage characteristics, etc., and to provide the basis for the analysis and judgment of PL(Product Liability) dispute by presenting a damage pattern due to a general flame and overcurrent. This study applied the Korean Standard (KS) for the incombustibility test of the connector using a general flame and performed an overcurrent characteristics test of the connector using PCITS (Primary Current Injection Test System). The contact resistance of the housing connector was measured using a high resistance meter and the insulation resistance was measured using a multimeter. In addition, a supply voltage of AC 1,500V for testing the withstanding voltage characteristics was applied to both ends of the connector. Measurement was performed on 5 specimens and the measured values were used as a basis for judgment. Since the connector is fabricated in the form of a housing, it can be connected and separated easily and has a structure that allows no foreign material to enter. In addition, since it has a structure that allows wires to be connected only when their polarity is identical, any misconnection that may occur during installation can be prevented. When the incombustibility test was performed by applying a general flame to the connector, it showed outstanding incombustibility characteristics and the blade and blade holder connected to the housing remained firmly secured even after the insulation sheath (PVC) was completely destroyed by fire. In addition, the mechanism of the damaged connecting wire showed a comparatively uniform carbonization pattern and it was found that some residual melted insulation material was attached to both ends. In the accelerated life test (ALT) to which approximately 500% of the rated current was applied, the connector damage proceeded in the order of white smoke generation, wire separation, spark occurrence and carbonization. That is, it could be seen that the connector damaged by overcurrent lost its own metallic color with traces of discoloration and carbonization. The contact resistance of the connector at a normal state was 2.164mV/A on average. The contact resistance measured after the high temperature test was 3.258mV/A. In addition, the insulation resistance after the temperature test was completed was greater than $10G\Omega$ and the withstanding voltage test result showed that no insulation breakdown occurred to all specimens showing stable withstanding voltage and insulation resistance characteristics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.182-187
• /
• 2011

In this paper, PBTI characteristics of NMOSFETs with La incorporated HfSiON and HfON are compared in detail. The charge trapping model shows that threshold voltage shift (${\Delta}V_{\mathrm{T}}$) of NMOSFETs with HfLaON is greater than that of HfLaSiON. PBTI lifetime of HfLaSiON is also greater than that of HfLaON by about 2~3 orders of magnitude. Therefore, high charge trapping rate of HfLaON can be explained by higher trap density than HfLaSiON. The different de-trapping behavior under recovery stress can be explained by the stable energy for U-trap model, which is related to trap energy level at zero electric field in high-k dielectric. The trap energy level of two devices at zero electric field, which is extracted using Frenkel-poole emission model, is 1,658 eV for HfLaSiON and 1,730 eV for HfLaON, respectively. Moreover, the optical phonon energy of HfLaON extracted from the thermally activated gate current is greater than that of HfLaSiON.

• Journal of Wetlands Research
• /
• v.15 no.3
• /
• pp.423-430
• /
• 2013

An algorithm to allow shoreline movement during numerical experiment on sediment transport, deposition or resuspension for general coastal morphology is proposed here. The bed slope near shoreline, i.e. mean sea level, is influenced by bed material, tidal current, waves, and wave-induced current, but has been reported to remain within a stable range. Its annual variation is not large, either. The algorithm is adjusting the bathymetry, if the largest bed slope within shoreline band exceeds a given bed slope due to continuous erosion at zones below the shoreline. This algorithm automatically describes retreat of shoreline caused by erosion, when used within a numerical system. The algorithm was tested to a situation which includes a continuous dredging at a point, and showed satisfactory development of concentric circle contours. Next, the algorithm was tested to another situation which includes sinking of eroded part of bed plate, and produced satisfactory results, too. Finally, the algorithm was tested to a movable-bed laboratory experimental conditions. The shoreline movement behind detached breakwater was reasonably reproduced with this algorithm.

• The Journal of the Korea Contents Association
• /
• v.9 no.6
• /
• pp.256-265
• /
• 2009

Laser output becomes output adjustment from 20 w to 100 w consecutively and time of exposure is available adjustment through water plant in 0.01 seconds. Pulse action can intercept laser beam periodically and supermarket pulse 0.1 $\sim$ between 1ms discharge consist and momentary laser output is increased to 5 $\sim$ 10. Specially, that must remove malignancy cell in womb nine escarps in the case of uterine cancer first of all stability of tube output about pulse by weight very, stable soft switching action area is defined without high frequency transformer leakage inductance ($L_1$) increase and additional series inductor insertion to converter the first main circuit securing zero voltage and marks of switching action in this research specially, because circulation current path of inductor ($L_f$) current is intercepted, converter the first main circuit switching component and spiritual enlightenment damage of high frequency transformer take decreasing greatly and high frequency the second stoppage department ($D_5,\;D_6$) becomes soft switching, and also, switching damage absorption quantity characteristic that can come to life again as subordinate have, and to become tube stabilization design and result that manufacture and experiment, brought result that improve of 10% than existing equipment, and if supplement as systematic late, it becomes thought to get into superior result.

• Journal of Convergence for Information Technology
• /
• v.11 no.9
• /
• pp.173-181
• /
• 2021

The purpose of this study is to prove the existence of the meridians by analyzing the effect of bloodletting cupping on Back-Shu Points and venesection on sabonghyeul, which are treatments for gastrointestinal and circulatory diseases with Ryodoraku. We selected the charts of 30 patients who received the treatment such as bloodletting cupping on Back-Shu Points and venesection on sabonghyeul for gastrointestinal and circulatory diseases. First, the Ryodoraku test was conducted in a stable state. After taking a rest on the bed, he performed a venesection on sabonghyeul. And bloodletting cupping on Back-Shu Points was performed with prone position. After all the procedures were completed, Ryodoraku test was performed again. And the result was compared with previous test status. By bloodletting cupping on Back-Shu Points and venesection on sabonghyeul, the deviation between the current value of the right F5 (gallbladder)· H4 (small intestine)· H6 (large intestine) (p<.05, p<.05, p<.001), left H5 (triple energizer) (p<.05) and the average current of 24 source points was significantly decreased. The difference between the left and right currents at the site of F3 (kidney) showed a significant increase (p<.005). It can be proved the existence of meridians that Bloodletting cupping on Back-Shu Points and venesection on sabonghyeul showed significant changes in the F5 (gallbladder), H4 (small intestine), H6 (large intestine), F3 (kidney), H5 (triple energizer) in digestive and circulatory symptoms by Ryodoraku test.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.49 no.2
• /
• pp.74-88
• /
• 2021

In the present study, the characteristics and changes in the vegetation of Mt. Cheongryang, Inchon, were examined to identify and determine appropriate ways to restore the health of the urban forest and to preserve its vegetation. The vegetation of the community of Quercus mongolica (Mongolian oak) on Mt. Cheongryang appeared to decrease in response to the control of the wilt disease of oak trees. The communities of Sorbus alnifolia (Korean mountain ash) and Styrax japonicus (Snowbell tree) have increased. Pinus rigida (Pitch Pine) had its overall territory decrease, but the current state of the Pinus rigida (Pitch Pine) was estimated to be stable due to its dominance as a tree layer species. In regards to Robinia pseudoacacia (Black Locust), the urbanized species of Sorbus alnifolia (Korean mountain ash), and Styrax japonicus (Snowbell tree), their areas have increased with the appearance of Magnolia obovate (Whiteleaf Japanese Magnolia). The biodiversity of Mt. Cheongryang has decreased by simplifying species in the tree layer and understory species thereof, and the initial success of species in marginal areas has increased. The absence of potential succession was attributed to the termination of ecological succession; thereby, the current vegetation structure was concluded to be remaining as it is for the time being. Soil texture in the mountain primarily consisted of sandy loam or loamy sand; the pH of the soil was in the range 4.26-4.86, rendering a mean pH of 4.59. The content of organic matter (O.M.) appeared having a distributing range of 2.18-9.60%, rendering a mean value of 4.33%. To promote species diversity, several methods are suggested, such as prevention of soil acidification, selecting nationally-grown trees from moist soil or valleys for afforestation, preventing species appearing due to urbanization or excessive growth, protecting the understory vegetation and species with hygropreference, and managing the forest to maintain a multi-layered vegetation structure.

• Korean Journal of Plant Resources
• /
• v.32 no.1
• /
• pp.45-52
• /
• 2019

In the process of adapting climate change, the government needs to provide policy and technical support necessary for growing promising crops imported from abroad. Therefore, this study was conducted to survey and analyze the conditions of growth of imported foreign crops and to derive response tasks. As a result, tropical and subtropical vegetables were cultivated 18 crops in 920 farms in 321 ha area (in 2015 year). The cultivation scale decreased in the order of Curcuma aromatica, Momordica charantia, Asparagus aethiopicus, Allium hookeri and Herbs. Tropical and subtropical fruits were cultivated 9 crops in 264 farms in 106.5 ha area (in 2015 year). Special and medicinal crops introduced abroad cultivated 10 crops in 753 farms in 276.3 ha area (in 2015 year). The cultivation scale decreased in the order of Curcuma longa, Glycyrrhiza uralensis, Lepidium meyenii and Moringa oleifera. For the stable settlement of domestic growth of tropical and subtropical crops introduced abroad, there should be safety and economic feasibility in terms of the cultivation environment according to the domestic culture adaptation test. Consideration needs to be given to the use of locally grown products in Korea, the securing of distribution and sales markets, and the competitiveness of imported products.