• Journal of the Korean Electrochemical Society
• /
• v.18 no.2
• /
• pp.68-74
• /
• 2015

To compare the microstructure and electrochemical properties between two binary alloys (Cr-Si, Ni-Si), two composition of binary alloys with the same capacity were selected using phase-diagram and prepared by matrix-stabilization method to suppress the volume expansion of Si by inactive-matrix. Master alloys were made by Arc-melting followed by fine structured ribbon sample preparation by Rapid Solidification Process (RSP, Melt-spinning method) under the same conditions. Also powder samples were produced by wet grinding for X-Ray Diffraction (XRD) and electrochemical measurements. As predicted from the phase diagram, only active-Si and inactive-matrix ($CrSi_2$, $NiSi_2$) were detected. The results of Scanning Electron Microscope (SEM) and Transmission Electron Microscopy - Energy Dispersive X-ray Spectroscopy (TEM-EDS) show that Cr-Si alloy has finer microstructure than Ni-Si alloy, which was also predictable through phase diagram. The electrochemical properties related to microstructure were evaluated by coin type full- and half-cells. Separately, self-designed test-cells were used to measure the volume expansion of Si during reaction. Volume expansion of Cr-Si alloy electrode with finer microstructure was suppressed significantly and improved in cycle capability, in comparison Ni-Si alloy with coarse microstructure. From these, we could infer the correlation of microstructure, volume expansion and electrochemical degradation and these properties might be predicted by phase diagram.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.9
• /
• pp.727-734
• /
• 2015

Recently, because of the increased oil prices globally, there have been studies investigating the improvement of fuel-conversion efficiency in internal combustion engines. The improvements realized in thermal efficiency using lean combustion are essential because they enable us to realize higher thermal efficiency in gasoline engines because lean combustion leads to an increase in the heat-capacity ratio and a reduction of the combustion temperature. Gasoline direct injection (GDI) engines enable lean combustion by injecting fuel directly into the cylinder and controlling the combustion parameters precisely. However, the extension of the flammability limit and the stabilization of lean combustion are required for the commercialization of GDI engines. The reduction characteristics of three-way catalysts (TWC) for lean combustion engines are somewhat limited owing to the high excess air ratio and low exhaust gas temperature. Therefore, in the present study, we assess the reaction of exhaust gases and their production in terms of the development of efficient TWCs for lean-burn GDI engines at 2000 rpm / BMEP 2 bar operating conditions, which are frequently used when evaluating the fuel consumption in passenger vehicles. At the lean-combustion operating point, $NO_2$ was produced during combustion and the ratio of $NO_2$ increased, while that of $N_2O$ decreased as the excess air ratio increased.

• Journal of Life Science
• /
• v.26 no.3
• /
• pp.353-358
• /
• 2016

Thiolase is an enzyme that catalyzes condensation reactions between two acetyl-CoA molecules to produce acetoacetyl-CoA. As thiolase catalyzes is the first reaction in the production of n-butanol, knowledge of the molecular and regulatory mechanism of the enzyme is crucial for synthesizing high-value biofuel. Thiolase from Clostridium butyricum (CbTHL) was expressed, purified, and crystallized. X-ray diffraction data were collected from the crystals, and the 3-dimentional structure of the enzyme was determined at 2.0 Å. The overall structure of thiolase was similar to that of type II biosynthetic thiolases, such as thiolase from C. acetobutylicum (CaTHL). The superposition of this structure with that of CaTHL complexed with CoA revealed the residues that comprise the catalytic and substrate binding sites of CbTHL. The catalytic site of CbTHL contains three conserved residues, Cys88, His349, and Cys379, which may function as a covalent nucleophile, general base, and second nucleophile, respectively. For substrate binding, the way in which CbTHL stabilized the ADP moiety of CoA was unlike that of other thiolases, whereas the stabilization of β-mercaptoethyamine and pantothenic acid moieties of CoA was quite similar to that of other enzymes. The most interesting observation in the CbTHL structure was that the enzyme was regulated through redox-switch modulation, using a reversible disulfide bond.

• Korean Journal of Clinical Laboratory Science
• /
• v.47 no.4
• /
• pp.243-250
• /
• 2015

A bone marrow biopsy that has undergone decalcification with 10% nitric acid could not be used for various pathological tests and had extremely limited reproducibility. The fixing solution of each experimental group was differentiated in usage, one solution including acid and the other not. The use of the decalcification solution was separated into either acidic or alkaline (EDTA), and further experiments were conducted with differing time phases. When using a fixing solution and decalcification solution which included acid, the specimens were faulty to the extent that all pathological tests were impossible. However specimens that were processed with an EDTA type decalcification solution did not display a non-specific reaction in EBV ISH and were even able to produce results that were at a level suited to various studies or a pathological diagnosis in the FISH, DNA, RNA tests. By improving the fixing and decalcification of bone marrow biopsy, the study was able to make possible ISH, FISH, DNA tests as well as RNA study, and secured the sensitivity, specificity, and reproducibility of various test methods. The stabilization of various test methods that use bone marrow biopsy contributes to the diagnosis, prognosis, prediction, treatment of the patient and provide guidelines for decision-making.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.380-392
• /
• 2012

Four kinds of N,O-hydroxypropyl chitosans (HPCTOs) with degree of substitution(DS) and molar substitution (MS) ranging from 2.47 to 2.52 and 4.9 to 7.8, respectively were synthesized, and their molecular chracteristics and thermotropic and lyotropic liquid crystalline properties were investigated. MS was exceedingly larger than DS, showing that in the later stages of reaction, propylene oxide was preferentially added to the side chains rather than the main chain. All the derivatives formed thermotropic cholesteric phases. The glass and clearing temperatures were decreased with increasing MS. The optical pitches (${\lambda}_m$'s) of the thermotropic cholesteric phases increased with temperature. However, the ${\lambda}_m$'s of the derivatives at the same temperature increased with increasing MS. Solutions of HPCTOs in water, methanol, ethanol, acetic acid, and formic acid containing more than 30 wt% polymer also formed cholesteic phases whose ${\lambda}_m$'s decreased exponentially with increasing polymer concentration. The concentration dependence of ${\lambda}_m$ of HPCTO solutions, however, highly depended on the nature of the solvent and MS. The thermotropic and lyotropic mesophase properties of HPCTOs were significantly different from those reported for hydroxypropyl celluloses. The results indicate that the secondary amino group in the C-2 position plays an important role on the formation, stabilization, and temperature and concentration dependencies of ${\lambda}_m$ of the cholesteric mesophase.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.1
• /
• pp.141-148
• /
• 2012

The objective of this study is to remove arsenate from artificially contaminated wastewater using CaAl-ettringite and CaAl-monosulfate which were synthesized in laboratory. The study was carried on the basis of solidification/stabilization of waste using cement. Monosulfate and ettringite are constituents of cement paste. The CaAl-ettringite has a chemical formula of $Ca_6Al_2O_6(SO_4)_3{\cdot}32H_2O$ and has a needle like morphology. Whereas CaAl-monosulfate $Ca_4Al_2O_6(SO_4){\cdot}12H_2O$ has layered double hydroxide structure (LDH) in which the mainlayer consists of Ca and Al and S as interlayer. Ettringite and monosulfate were synthesized by reaction of tricalcium aluminate and gypsum and hydrating this mixture at elevated temperature. The synthesized mineral were characterized by PXRD and FESEM to ensure purity. It was found that concentrations of As(V) in contaminated water were reduced from initial concentration of 1.335 mmol/L to 0.054 mmol/L and 0.300 mmol/L by CaAl-monosulfate and CaAl-ettringite respectively. The post experimental results of PXRD and FESEM analysis indicate that arsenate removal was by ion exchange.

• Journal of Chest Surgery
• /
• v.30 no.7
• /
• pp.701-707
• /
• 1997

Although many reseraches have been persued to detect the molecular tumor marker to define the cancer, ideal tumor marker which speak for the characteristics of malignancy and has high sensitivity and specificity is not known. One of the characteristics of the malignant cells is indefinite proliferative potential, in other word, immortality. The expression of telomerase and stabilization of te10meres are con omitant with the attaiunent of immortality in tumor cells; thus the measurement of telomerase activity in clinically obtained tumor samples may provide important information which would be useful as a diagnostic marker to detect immortal cancer cells. Telomerase activity was analyzed in 12 non-small cell . lung cancer cell lines and 41 primary non-small cell lung cancers with the use of a PCR-based assay. All the cell lines and the majority of tumors displayed telomerase activity, but telomerase was not detectable in most of the corresponding pathologically-normal tissues. Telomere length was not correlated with telomerase activity. The present study indicate that measurement of telomerase activity may be useful as a molecular tumor marker in non-small cell lung cancer.

• The korean journal of orthodontics
• /
• v.40 no.1
• /
• pp.34-39
• /
• 2010

Objective: The aim of the present study was to evaluate the changes in tooth mobility following orthodontic treatment and to obtain information regarding the guideline of retainer wear duration during the post-treatment period. Methods: The sample consisted of twenty patients who had been treated with edgewise appliances. The mobility of the maxillary teeth from the central incisor to the first molar was measured bilaterally by way of the $Periotest^{(R)}$, a non-invasive, electronic device that provides an objective measurement of the reaction of the periodontium to a defined impact load. Tooth mobility was monitored at the time of the removal of the orthodontic appliances and subsequently at three-month intervals during the two years following appliance removal. Results: Tooth mobility decreased rapidly for the first six months and then decreased at a slower rate during the next six months; no statistically significant decrease in mobility was observed during the second year following appliance removal. Conclusions: The results of the present study suggest that adequate tooth stabilization is critical during the first six months following appliance removal and that continued wearing of retainers is recommended at least until twelve months after the completion of orthodontic treatment.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.9
• /
• pp.3295-3305
• /
• 2011

Thermal behavior of poly (methyl methacrylate) was analyzed in the presence of tin (IV) chloride. Five different proportions - polymer to additive - were selected for casting films from common solvent. TG, DTG and DTA were employed to monitor thermal degradation of the systems. IR and py-GC-MS helped identify the decomposition products. The blends start degrading at a temperature lower than that of the neat polymer and higher than that of the pure additive. Complex formation between tin of additive and carbonyl oxygen (pendent groups of MMA units) was noticed in the films soon after the mixing of the components in the blends. The samples were also heated at three different temperatures to determine the composition of residues left after the expulsion of volatiles. The polymer, blends and additive exhibited a one step, two-step and three-step degradation, respectively. $T_0$ is highest for the polymer, lowest for the additive and is either $60^{\circ}C$ or $70^{\circ}C$ for the blends. The amount of residue increases down the series [moving from blend-1 (minimum additive concentration) to blend-5 (maximum additive concentration)]. For blend-1, it is 7% of the original mass whereas it is 16% for blend-5. $T_{max}$ also goes up as the concentration of additive in the blends is elevated. The complexation appears to be the cause of observed stabilization. Some new products of degradation were noted apart from those reported earlier. These included methanol, isobutyric acid, acid chloride, etc. Molecular-level mixing of the constituents and "positioning effect" of the additive may have brought about the formation of new compounds. Routes are proposed for the appearance of these substances. Horizontal burning tests were also conducted on polymer and blends and the results are discussed. Activation energies and reaction orders were calculated. Activation energy is highest for the polymer, i.e., 138.9 Kcal/mol while the range for blends is from 51 to 39 Kcal/mol. Stability zones are highlighted for the blends. The interaction between the blended parts seems to be chemical in nature.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 2001.11a
• /
• pp.102-102
• /
• 2001

Taurine (2-ethaneaminosulfonic acid) is one of the major intracellular ${\beta}$ -amino acids in mammals and is required for a number of biological processes including membrane stabilization, osmoregulation, antioxidation, detoxification, modulation of calcium flux and neurornodulation. The taurine transporter (TAUT) which contains 12 hydrophobic membrane-spanning domains has been cloned from dog kidney, rat brain, mouse brain, human thyroid, placenta and retina. In this study, The TAUT cDNA from the human intestinal epithelial cell, HT-29 was cloned and sequenced. Reverse-transcription polymerase chain reaction (RT-PCR) was performed to amplify partial cDNA encoding human intestinal TAUT. The coding region of the PCR product was 732 bp long. The primers were designed to encode highly conserved amino acid sequences near the transmembrane domains III (IPYFIFLF) and Ⅵ (KYKYNSYR) both in human and mouse. The TAUT cDNA amplified was ligated into the pGEX 4T-1 expression vector. The resulting sequence of human intestinal TAUT cDNA (Accession number of NCBI Genebank is AF346763) was identical to the sequences of the TAUTs previously determined in the human placenta and retina except 3 base pairs from that of the reported human thyroid. TAUT specific antibodies were generated to use them as biological tools in the studies of the biological role of TAUT. Peptides of 149-162 amino acid residue (14 amino acids) of the TAUT were synthesized. The synthetic peptide used in this study was LFQSFQKELPWAHC. This region was chosen not only to avoid putative glycosylation sites but also to exclude regions of known homology with GABA transporters in the extracellular hydrophilic domains. The synthetic peptide, TAUT-1 was conjugated with carrier protein, kehole lympet hemocyanin (KLH) to use as an antigen. When used for immunization on a rabbit to produce polyclonal antiserum, the conjugates elicited high -titered specific anti-TAUT-1 antibodies, which reacted well with the ovalbumin (OVA) conjugated peptides in ELISA. The KLH-conjugated peptide was also used as immunizing antigen in BALB/c mice to produce TAUT specific monoclonal antibodies. From the culture supernatant of the hybridoma, the specificity of anti-TAUT-1 monoclonal antibodies was confirmed by ELISA. Further applications of more tools in TAUT expression analysis will be performed such as western blotting and flow cytometry.