• International Journal of Highway Engineering
• /
• v.20 no.4
• /
• pp.21-26
• /
• 2018

PURPOSES : The objective of this study is to evaluate the application of soil stabilization method for soft shoulder construction in the iRoad Project of Sri Lanka. METHODS : Firstly, the quantitative analysis of soil strength improvement due to soil stabilization was done for soil samples collected from iRoad construction sites. Two types of soils were selected from iRoad Project sites and prepared for soil stabilization testing by the Road Development Authority. Secondly, the appropriate stabilizer was selected at given soil type based on test results. Two different stabilizers, ST-1 and ST-2, produced in Korea were used for estimating soil strength improvements. Finally, the optimum stabilizer content was determined for improving shoulder performance. The uniaxial compressive strength (UCS) test was conducted to evaluate the strength of stabilized soil samples in accordance with ASTM D 1633. The use of bottom ash as a stabilizer produced from power plant in Sri Lanka was also reviewed in this task. RESULTS : It is found from the UCS testing that a 3% use of soil stabilizer can improve the strength up to 2~5 times in stabilized soft shoulder soils with respect to unstabilized soils. It is also observed from UCS testing that the ST-1 shows high strength improvement in 3% of stabilizer content but the strength improvement rate with increase of stabilizer content is relatively low compared with ST-2. The ST-2 shows a low UCS value at 3% of content but the UCS values increase significantly with increase of stabilizer content. When using the ST-2 as stabilizing agent, the 5% is recommended as minimum content based on UCS testing results. Based on the testing results for bottom ash replacement, the stabilized sample with bottom ash shows the low strength value. CONCLUSIONS : This paper is intended to check the feasibility for use the soil stabilization technique for shoulder construction in Sri Lanka. The use of soil stabilizer enables to improve the durability and strength in soft shoulder materials. When applying the bottom ash as a soil stabilizer, various testings should be conducted to satisfy the specification criteria.

• Journal of Soil and Groundwater Environment
• /
• v.22 no.6
• /
• pp.1-11
• /
• 2017

This study was conducted to investigate the performance of four commercial chemical agents in stabilizing arsenic (As) in soil at the forest area near the former Janghang smelter site. After amending the stabilizing agents (A, B, C, and D) into As-contaminated soil samples, synthetic precipitation leaching procedure (SPLP) and solubility bioavailability research consortium (SBRC)-extractable As concentrations significantly decreased except for agent D, which is mainly composed of fly ash and calcium carbonate. Increase of SPLP and SBRC-extractable As concentrations in four soil samples (S1, S2, S3, and J2) was attributed to desorption of As adsorbed on iron oxides due to high pH generated by agent D. It is therefore necessary to consider application conditions according to soil characteristics such as pH and buffering capacity. Results of sequential extraction showed that readily extractable fractions of As in soil (i.e., sum of $SO_4-$ and $PO_4-extractable$ As in soil) were converted into non-readily extractable fractions by amending agents A, B, and C. Such changes in the As distribution in soil resulted in the decrease of SPLP and SBRC-extractable As concentration. A series of follow-up monitoring and management plan has been suggested to assess the longevity of the stabilization treatments in the site.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.453-458
• /
• 2001

This study was performed to reuse the dyeing wastewater sludge treated by Fenton process through the solidification/stabilization technique. To solidify the dyeing sludge the industrial by-products such as blast furnace slag, fly ash and waste sand with cement were used. The laboratory scale and pilot scale test were conducted at room temperature to make construction brick which has high compressive strength and low leaching of heavy metals. The experimental results showed that blast furnace slag and fly ash could be used instead of cement and the products satisfied the regulation of Korean Standards. The blast furnace slag increased the compressive strength and the optimum ratio of slag/dyeing sludge on dry basis was found 0.4. The solidifying agent of SB series could increase rapidly the compressive strength and the optimum ratio of solidifying agent/sludge on dry basis was 0.26 at which the strength was two times compared with non-added condition. The portion of waste and industrial by-products in matrix was over 80%. From the pilot test the optimum pressure in molding was 100kg/$\textrm{cm}^2$ at which the compressive strength was over 100kg/$\textrm{cm}^2$. And the strength increased continuously to 160kg/$\textrm{cm}^2$ until 120 days curing time due to pozzolanic reaction. When SB-20 as a solidifying agent was used, the unconfined compressive strength of dyeing sludge could be obtained 110kg/$\textrm{cm}^2$ which satisfied the regulation of cement brick in Korea Standard(KS).

• Journal of Soil and Groundwater Environment
• /
• v.22 no.4
• /
• pp.27-32
• /
• 2017

In this study, a remedial investigation using reductive stabilization was conducted to treat Cr(VI)-contaminated soil. The influences of various operational parameters, including reaction time and the mass of ferrous iron, were also evaluated. The study site was contaminated with a large amount of Cr(III) and Cr(VI), and the selected treatment method was to stabilize Cr(VI) with ferrous iron, which reduced Cr(VI) to Cr(III) and stabilized the chromium, although a greater mass of ferrous iron than the stoichiometric amount was required to stabilize the Cr(VI). However, some Cr(III) re-oxidized to Cr(VI) during the drying process, and addition of a strong reducing agent was required to maintain reducing conditions. With this reducing agent, the treated soil met the required regulatory standard, and the mass of Cr(III) re-oxidized to Cr(VI) was significantly reduced, compared to the use of only Fe(II) as a reducing agent.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.6
• /
• pp.1-10
• /
• 2022

This study assessed the feasibility of iron oxide nanoparticles impregnated with biochar (INPBC), derived from woody biomass, as a stabilizing agent for the stabilization of farmland soil in the vicinity of an abandoned mine through pot experiments with 28 days of lettuce growth. The lettuce grown in the INPBC amended soils increased by more than 100% and the concentrations of inorganic elements (Cu, Ni, Zn) decreased by more than 40%. As, Cd and Pb were not transferred properly from the soils to the lettuce biomass. The bioavailability of arsenic and heavy metals in the INPBC amended soils were decreased by 26%~50%. It seems that the major mechanisms of stabilization were arsenic adsorption on iron oxides, heavy metal precipitation by soil pH increasing and heavy metal adsorption on organic matter. These results revealed that the lower bioavailability of the inorganic pollutants in the soils stabilized using INPBC induced lower transfer to the lettuce. Thus, INPBC could be used as an amendment material for the stabilization of farmland soils contaminated by arsenic and heavy metals. However, a pre-review of the chemical properties of the amended soil must be performed prior to applying INPBC in farmland soil because the concentration of the nutrients in the soil such as available phosphates and exchangeable cations (Ca, Mg, K) could be decreased due to adsorption on the surface of the iron oxides and organic matter.

• Journal of the Korean Society of Safety
• /
• v.31 no.1
• /
• pp.66-73
• /
• 2016

Lyocell fibers were used as a precursor in order to improve yield and strength of cellulose-based precursor while manufacturing activated carbon fiber(ACF). Lyocell fibers as a precursor for the preparation of ACF were surface-modified by reaction with 3-aminopropyltriethoxysilane(APTES) and pre-treated with KOH and H3PO4. Using aforementioned precursor, ACFs were prepared by a series of stabilization, carbonization and activation process at high temperatures. On each process, FT-IR, TGA, UTM and SEM were used to observe fibers' physical properties including structure and porous surfaces. FT-IR results proved that surface modification was achieved during stabilization, carbonization and activation process. TGA results during carbonization process found that surface modified fibers with APTES 0.02 mol(A2) showed higher thermostability, and extended pre-treatment increased yield. Especially, yield was found to have an increase of 10~20 wt% with surface modification during activation process. UTM results showed that tensile strength has the same order of concentration of APTES after surface modification, however, was found to show lower tensile strength than lyocell fibers after stabilization process. SEM results revealed that more homogeneous porosity control could be proceed after modifying the surface for the effective removal of hazardous substances.

• Biomolecules & Therapeutics
• /
• v.22 no.1
• /
• pp.73-77
• /
• 2014

The purpose of this study was to examine the effect of stabilization of retinyl palmitate (RP) on its skin permeation and distribution profiles. Skin permeation and distribution study were performed using Franz diffusion cells along with rat dorsal skin, and the effect of drug concentration and the addition of pectin on skin deposition profiles of RP was observed. The skin distribution of RP increased in a concentration dependent manner and the formulations containing 0.5 and 1 mg of pectin demonstrated significantly increased RP distributions in the epidermis. Furthermore, it was found that skin distribution of RP could be further improved by combined use of pectin and ascorbyl palmitate (AP), due largely to their anti-oxidative effect. These results clearly demonstrate that the skin deposition properties of RP can be improved by stabilizing RP with pectin. Therefore, it is strongly suggested that pectin could be used in the pharmaceutical and cosmetic formulations as an efficient stabilizing agent and as skin penetration modulator.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.3
• /
• pp.75-82
• /
• 2003

This paper presents the results of a study that was performed to evaluate fronds of shear strength parameters in stabilization of unbound soil-aggregate systems based on the theory of unsaturated soil mechanics. Two important shear strength parameters, effective cohesion and effective angle of internal friction were estimated by the proposed approach using the results from suction measurements and unconfined compressive strength test. In addition, the effect of different addition rates of stabilizing agent was compared. Due to the stabilization process, an increase in suction potential on engineering properties of geomaterials was observed by using dielectric constant measurements. In conclusion, the results from this study show that the proposed approach can be simply used for predicting shear strength parameters of the stabilized geomaterials.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.4
• /
• pp.36-44
• /
• 2003

The cement-based system among S/S(Solidification/Stabilization) is widely used to treat hazardous wastes. In this study, tannery sludge was solidified to evaluate the stabilization effects of using admixtures in the cement-based S/S. Fly ash as substitute also used to increase the strength of the S/S of hazardous waste. The compressive strength measurement and leaching experiment of chromium metal of solidified mortar were carried out to compare and evaluate the physical and chemical characteristics of solidified hazardous waste sludge. From the result of this study, there was increased of compressive strength by using AEW-3(early-hardening AE water reducing agent), and leaching concentration of chromium became low enough to satisfy the regulatory criteria. The successful solidification for the organic contaminant and heavy metal in hazardous waste should enable to treat by cement-based system using early-hardening AE water reducing admixture and fly ash as substituted cement.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.941-947
• /
• 2011

This paper deals with the consensus problem for multi-agent linear dynamic systems with directed communication topology. All the agents are identical high-order linear systems and their state information is exchanged through a communication network with directed graph. It is shown that a consensus is achieved if there exists a feasible solution to a set of linear matrix inequalities obtained for a simultaneous stabilization problem for multiple systems. Examples are presented to show the effectiveness of the proposed method.