• The Journal of the Acoustical Society of Korea
• /
• v.10 no.2
• /
• pp.13-22
• /
• 1991

The presence of an unbalanced mass is originated the common source of vibration in machines with rotating rotor. In this study, the unbalanced rigid rotor mounted on an overhang shaft is balanced using the static balancing procedure, and the compensation mass is estimated by the phase angle method and four run method. Also, the reduction of vibration level before and after balancing is examined. In the experimental results, it is shown that the vibration due to the unbalanced mass is decreased by eliminating the effect of the unbalance. Above all, the four run method is proved more effective on the ability of vibration reduction, in small unbalanced mass, the phase angle method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1211-1217
• /
• 2000

The three-dimensional finite-difference time-domain (FDTD) method and the two-dimensional quasi-static formulation have been used to calculate the characteristic impedance and the microwave effective index of coplanar waveguide structures on Lithium Niobate ($LiNBO_3$) single crystal substrates with a yttria-stabilized zirconia (YSZ) or $SiO_2$ buffer layer. The results shown can be a good source to predict the modulator characteristics. The effects of the thin buffer layer and anisotropy of the $LiNBO_3$ crystal (x-cut and z-cut) are discussed. The comparison between the FDTD and quasi-static results shows good agreement. In this paper, the efficient modeling technique of the FDTD method for the coplanar waveguide (CPW) structures based on an anisotropic substrate with a thin buffer layer is developed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.9
• /
• pp.828-833
• /
• 2011

A reaction wheel assembly(RWA) is the largest disturbance source that can induce high frequency micro-vibration on an optical payload of satellites. To ensure a tight pointing-stability budget of satellites, the RWA disturbance effect on spacecraft should be accurately analyzed and evaluated for whole design phases. For this purpose, the micro-vibration disturbance of RWA should be precisely measured. In the present study, two measurement methods on RWA micro-vibration disturbances are compared and investigated. One is a free run-down speed test and the other is a constant speed test. The micro-vibration data measured by the two methods are analyzed in terms of spectrum characteristics, static and dynamic imbalance values, and root sum square(RSS) values. The analysis results show that both methods can measure very similar results in time and frequency domains and that the free run-down speed method is more adequate in respects to wheel friction modeling, noise rejection of imbalance and RSS peak evaluation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.540-543
• /
• 2007

In this paper, we propose a new approach to reduce the audible noise generated by TFT-LCD module in mobile applications. We also analyzed impact factors which effect on the audible noise. It is expected that this noise source comes from various impact factors such as vibration of flexible printed-circuit board (FPCB) and LCD panel, and static electricity charged in window and back-light unit. Windowless type and window type models are evaluated to analyze noise level due to the static electricity charged in window. To obtain reliable and reproducible data, we constructed controllable test jig and measurement set-up.

• Journal of information and communication convergence engineering
• /
• v.7 no.4
• /
• pp.475-479
• /
• 2009

In ad hoc network, the scarce energy management of the mobile devices has become a critical issue in order to extend the network lifetime. Current research activity for the Minimum Energy Multicast (MEM) problem has been focused on devising efficient centralized greedy algorithms for static ad hoc networks. In this paper, we consider mobile ad hoc networks(MANETs) that could provide the reliable monitoring and control of a variety of environments for remote place. Mobility of MANET would require the topology change frequently compared with a static network. To improve the routing protocol in MANET, energy efficient routing protocol would be required as well as considering the mobility would be needed. In this paper, we propose a new method, the CACH(Context-aware Clustering Hierarchy) algorithm, a hybrid and clustering-based protocol that could analyze the link cost from a source node to a destination node. The proposed analysis could help in defining the optimum depth of hierarchy architecture CACH utilize. The proposed CACH could use localized condition to enable adaptation and robustness for dynamic network topology protocol and this provide that our hierarchy to be resilient. As a result, our simulation results would show that CACH could find energy efficient depth of hierarchy of a cluster.

• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.85-90
• /
• 2010

In this paper the effects of a Static Synchronous Series Compensator, which is constructed with a 48-pulse inverter, on the power demand from the grid are studied. Extensive simulation studies were carried out in the MATLAB simulation environment to observe the compensation achieved by the SSSC and its effects on the line voltage, line current, phase angle and real/reactive power. The designed device is simulated in a power system which is comprised of a three phase power source, a transmission line, line inductance and load. The system parameters such as line voltage, line current, reactive power Q and real power P transmissions are observed both when the SSSC is connected to and disconnected from the power system. The motivation for modeling a SSSC from a multi-pulse inverter is to enhance the voltage waveform of the device and this is observed in the total harmonic distortion (THD) analysis performed at the end of the paper. According to the results, the power flow and phase angle can be controlled successfully by the new device through voltage injection. Finally a THD analysis is performed to see the harmonics content. The effect on the quality of the line voltage and current is acceptable according to international standards.

• Journal of Power Electronics
• /
• v.13 no.5
• /
• pp.877-883
• /
• 2013

This paper discussed a transformer-less shunt static synchronous compensator (STATCOM) with consideration of the following aspects: fast compensation of the reactive power, harmonic cancelation and reducing the unbalancing of the 3-phase source side currents. The STATCOM control algorithm is based on the theory of instantaneous reactive power (P-Q theory). A self charging technique is proposed to regulate the dc capacitor voltage at a desired level with the use of a PI controller. In order to regulate the DC link voltage, an off-line Genetic Algorithm (GA) is used to tune the coefficients of the PI controller. This algorithm arranged these coefficients while considering the importance of three factors in the DC link voltage response: overshoot, settling time and rising time. For this investigation, the entire system including the STATCOM, network, harmonics and unbalancing load are simulated in MATLAB/SIMULINK. After that, a 35KVA STATCOM laboratory setup test including two parallel converter modules is designed and the control algorithm is executed on a TMS320F2812 controller platform.

• Geomechanics and Engineering
• /
• v.20 no.5
• /
• pp.447-459
• /
• 2020

Based on the literature statistical method, the paper publication status of the isolated working face and the distribution of the rockburst coal mine were obtained. The numerical simulation method is used to study the stress distribution law of working face under different mining range. In addition, based on the similar material simulation test, the overlying strata failure modes and the deformation characteristics of coal pillars during the mining process of the isolated working face with thick-hard key strata are analyzed. The research shows that, under the influence of the key strata, the overlying strata formation above the isolated working face is a long arm T-type spatial structure. With the mining of the isolated working face, a series of damages occur in the coal pillars, causing the key strata to break and inducing the rockburst occurs. Combined with the mechanism of rockburst induced by the dynamic and static combined load, the source of dynamic and static load on the isolated working face is analyzed, and the rockburst monitoring methods and the prevention and control measures are proposed. Through the above research, the occurrence probability of rockburst can be effectively reduced, which is of great significance for the safe mining of deep coal mines.

• Journal of KIISE:Software and Applications
• /
• v.37 no.12
• /
• pp.942-945
• /
• 2010

In order to reduce the efforts to inspect the reported alarms from a static buffer overflow analyzer, we present an effective method to filter out redundant alarms. In the static analysis, a sequence of multiple alarms are frequently found due to the same cause in the code. In such a case, it is sufficient and reasonable for programmers to examine the first alarm instead of the entire alarms in the same sequence. Based on this observation, we devise a buffer overflow analysis that filters out redundant alarms with our context refinement technique. Our experiment with several open source programs shows that our method reduces the reported alarms by 23% on average.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.6
• /
• pp.51-59
• /
• 2011

In domestic, the binary code analysis technology is insufficient. In general, an executable file that is installed on your computer without the source code into an executable binary files is given only the most dangerous, or because it is unknown if the action is to occur. In this paper, static program analysis at the binary level to perform the design and implementation framework. In this paper, we create a control flow graph. We use the graph of the function call and determine whether dangerous. Through Framework, analysis of binary files is easy.