• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6804-6809
• /
• 2014

This paper presents a bandpass filter using a current differencing transconductance amplifier (CDTA)s for application to low-voltage and low-power analog signal processing systems. The presented filter employs grounding and floating active inductors, which are composed of two or three CDTAs, and is capable of realizing all the standard functions of the filter without requiring any component matching criteria or extra active components. The HSPICE simulation result of the designed active bandpass filter showed that it had a 10MHz center frequency with -2.5dB attenuated bandwidth from 9.5 MHz to 10.5 MHz, and -50dB from 8 MHz to 17 MHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.166-172
• /
• 2001

A RF wideband receiver for INMARSAT-B satellite communications system was composed of low noise amplifier and high gain amplifier, The low noise amplifier used to the resistive decoupling circuit for input impedance matching and self-bias circuits for low noise. The high gain amplifier consists of matched amplifier type to improve receiver gain. The active bias circuit can be used to provide temperature stability without requiring the large voltage drop or relatively high-dissipated power needed with a bias stabilization resistor. The bandpass filter was used to reduce a spurious level. As a result, the characteristics of the receiver implemented here show more than 60 dB in gain and less than 1.8:1 in input and output voltage standing wave ratio(VSWR), especially the carrier to noise ratio which is input signal level -126.7 dB m at 1537.5 MHz is a 45.23 dB /Hz at a 1.02 kHz.

• Journal of Advanced Navigation Technology
• /
• v.16 no.3
• /
• pp.433-439
• /
• 2012

In this paper, we proposed the triplexer using unit-cell of CRLH transmission line which has a bandpass characteristic to reduce adjacent channel interference. The input impedance of triplexer with each channel filter is operated open-circuit at the resonance frequencies of other channels. Such property is due to the combination a series and parallel resonance circuits of CRLH-TL unit-cell. The measured triplexer results are showed a measured insertion loss of each channel, less than 1.5 dB, matching at each port, less than 15dB and isolation between channel, better than 25 dB. Also, to validate the triplexer, a small signal amplifier with triple-band is designed and tested. the measured amplifier results show good agreements with prediction.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.5
• /
• pp.48-55
• /
• 1999

This paper describes automatic gain control circuit (AGC) design techniques for CMOS CCD camera interface systems. The required gain of the AGC in the proposed system is controlled directly by digital bits without conventional extra D/A converters and the signal settling behavior is almost independent of AGC gain variation at video speeds. A capacitor-segment combination technique to obtain large capacitance values considerably improves the effective bandwidth of the AGC based on switched-capacitor techniques. A proposed layout scheme for capacitor implementation shows AGC matching accuracy better than 0.1 %. The outputs from the AGC are transferred to a 10b A/D converter integrated on the same chip. The proposed AGC is implemented as a sub-block of a CCD camera interface system using a 0.5 um n-well CMOS process. The prototype shows the 32-dB AGC dynamic range in 1/8-dB steps with 173 mW at 3 V and 25 MHz.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.4
• /
• pp.49-58
• /
• 2014

A low-swing differential near-ground signaling (NGS) transceiver for low-power high-speed mobile I/O interface is presented. The proposed transmitter adopts an on-chip regulated programmable-swing voltage-mode driver and a pre-driver with asymmetric rising/falling time. The proposed receiver utilizes a new multiple gain-path differential amplifier with feed-forward capacitors that boost high-frequency gain. Also, the receiver incorporates a new adaptive bias generator to compensate the input common-mode variation due to the variable output swing of the transmitter and to minimize the current mismatch of the receiver's input stage amplifier. The use of the new simple and effective impedance matching techniques applied in the transmitter and receiver results in good signal integrity and high power efficiency. The proposed transceiver designed in a 65-nm CMOS technology achieves a data rate of 13 Gbps/channel and 0.3 pJ/bit (= 0.3 mW/Gbps) high power efficiency over a 10 cm FR4 printed circuit board.

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.30-37
• /
• 2007

This paper proposes a detection method of position of OFF-switch. Each switch has the parallel path with a serial combination of passive element, its parallel path has each different frequency characteristics. Frequency characteristic of ON-switch reveals a flat spectrum irrelevant to frequency characteristic of passive element connected in parallel to its each terminal and frequency characteristic of OFF-switch reveals the same characteristic as one of passive element connected in parallel. Detection of position of OFF-switch is done by measuring the similarity of each spectrum corresponding to frequency characteristic of passive element connected in parallel to OFF-switch. The measure of their similarity is to calculate Euclidean distance between their test spectrum and reference spectrum. The spectrum with the smallest distance among reference spectrum is recognized as the spectrum of OFF-switch. The real time digital signal processing system is implemented to detect the position of OFF-switch by using spectrum matching.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.6
• /
• pp.665-670
• /
• 2015

In this paper, We proposed a broadband RF amplifier for Microwave band receiver. We also proposed a broadband RF amplifier, designed by using EM simulation for reliable amplification of the received signal. Connected to a source terminal to via, it minimizes those which are the active elements of source-side oscillation as the operating element in an ideal GND, and a constant gain characteristic in a broadband. The goal of this was to obtain stable amplification characteristics. For implementing this architecture, we designed the broadband(500 MHz ~ 7 GHz) RF amplifier by using commercial GaAs FET, which operate on 720 MHz, 4,595 MHz, and 6,035 MHz by impedance matching. The voltage gain is 10.635 dB ~ 14.407 dB(737.5 MHz ~ 6.0575 GHz), P1dB is 20 dBc of band(1st harmonic/2nd harmonic).

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.1
• /
• pp.23-28
• /
• 2016

In this paper, a Multi-Band Ku-band down converter was designed for reception of multi-band digital satellite broadcasting. The Multi-band low-nose down converter was designed to form four local oscillator frequencies (9.75, 10, 10.75 and 11.3GHz) representing a low phase noise due to VCO-PLL with respect to input signals of 10.7 to 12.75GHz and 3-stage low noise amplifier circuit by broadband noise matching, and to select an one band of intermediate frequency (IF) channels by digital control. The developed low-noise downconverter exhibited the full conversion gain of 64dB, and the noise figure of low-noise amplifier was 0.7dB, the P1dB of output signal 15dBm, and the phase noise -73dBc@100Hz at the band 1 carrier frequency of 9.75GHz. The low noise block downconverter (LNB) for receiving four-band digital satellite broadcasting designed in this paper can be used for satellite broadcasting of vessels navigating international waters.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.1-8
• /
• 2019

The HPM (High-speed Power Matching) system is an electro-hydraulic control system. It directly controls the swash plate of the pump by selecting four-loop logic based on joystick signals, pump flow, and pressure signal to improve the efficiency and controllability of construction machines. In the NFC (Negative Flow Control) system, a typical pump control system using conventional open center type MCV, the loss is continuously generated by flow through the center bypass line even when the excavator is not in operation. Also, due to the slow response of the pump that indirectly controls the flow rate using the pressure regulator, peak pressure occurs at the start or stop of the operation. Conversely, the HPM system uses an MCV without center-by-pass flow path and the swash plate of a pump for the HPM is controlled by a high-speed proportional flow control valve. As a result, the HPM system minimizes energy loss in standby state of the excavator and enables peak pressure control through rapid electro-hydraulic control of a pump. In this paper, the concept of the HPM system algorithm is introduced and the hydraulic system efficiency is compared with the NFC system using the excavator SAT (System Analysis Tool).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.11
• /
• pp.2479-2485
• /
• 2013

In this paper, we present a design for solid-state radar SSPA with sequential bias. We apply to variable extension pulse generator to eliminate signal distortion which is caused by bias rising/falling delay of power amplifier. There is an optimum impedance matching circuit to have high efficiency of GaN-power device by measuring microwave characteristics through load-pull method. The designed SSPA is consisted of pre-amplifier, drive-amplifier and main-amplifier as a three stages to apply for X-Band solid-state radar. Thereby we made a 200W SSPA which has output pulse maximum power shows 53.67dBm and its average power is 52.85dBm. The optimum design of transceiver module for solid-state pulse compression radar which is presented in this dissertation, it can be available to miniaturize and to improve the radar performances through additional research for digital radar from now on.