• Korea-Australia Rheology Journal
• /
• 제13권3호
• /
• pp.131-139
• /
• 2001

A coupled approach is proposed for the prediction of sheet profile in sheet casting process, which combines one-dimensional analytical method on planar elongational flow region and three-dimensional numerical method on the other region. The strategy is constructed from the observations that the flow domain of sheet casting process can be separated into two parts based old the flow kinematics. The flow field in the central region of sheet, over which the planar elongational flow dominates, is possibly replaced by one-dimensional analytical solution. Then only a partial flow domain near the edge region of sheet, where the flow kinematics cannot be described by the planar elongational flow itself, requires three-dimensional numerical simulation. Good agreement is observed between the coupled approach developed in this study and the full three-dimensional numerical simulation previously developed and reported by the authors. This coupled approach may have provided flexibility with low costs to accommodate a wide range of die sizes in sheet casting process.

• 열처리공학회지
• /
• 제36권6호
• /
• pp.359-366
• /
• 2023

Changes in microstructure and mechanical properties of Mg-1.0Al-1.0Zn-0.2Mn-0.5Ca (AZMX1100) alloy sheet manufactured by normal casting and twin roll casting process, were studied according to process and heat treatment. Non-uniform microstructure was observed in the initial sheet produced through both processes, and in particular, tilted dendrites and shifted central segregation were observed in the twin roll casting sheet. It was homogenized through hot rolling and heat treatment, and heat treated at 350℃ and 400℃ to compare the effect of heat treatment temperature. Both sheets were homogenized by the hot rolling process, and the grain size increased as the heat treatment temperature and time increased. It was confirmed that the grain size, deviation, and distribution of the second phase were finer and more homogenized in the TRC sheet. Accordingly, mechanical properties such as hardness, formability, and tensile strength also showed better values. However, unlike other previously reported AZMX alloy systems, it showed low formability (Erichsen value), which was judged by the influence of Al2Ca present in the microstructure.

• Korea-Australia Rheology Journal
• /
• 제12권2호
• /
• pp.107-117
• /
• 2000

Prediction of the product shape in sheet casting process is performed from the numerical simulation. A three-dimensional finite element method is used to investigate the flow behavior and to examine the effects of processing conditions on the sheet produced. Effects of inertia, gravity, surface tension and non-Newtonian viscosity on the thickness profile of the sheet are considered since the edge bead and the flow patterns in the chill roll region have great influence on the quality of the products. In the numerical simulation with free surface flows, the spine method is adopted to update the free surface, and the force-free boundary condition is imposed along the take-up plane to avoid severe singularity problems existing at the take-up plane. From the numerical results of steady isothermal flows of a generalized Newtonian fluid, it is shown that the draw ratio plays a major role in predicting the shape of the final sheet produced and the surface tension has considerable effect on the bead thickness ratio and the bead width fraction, while shear-thinning and/or tension-thickening viscosity affect the degree of neck-in.

• 자원리싸이클링
• /
• 제26권5호
• /
• pp.22-28
• /
• 2017

이차전지온도퓨즈시스템에 In-Bi-Sn계 저온가용합금 박판이 사용되고 있다. 본 연구에서는 온도퓨즈시스템에 사용될 수 있는 적절한 조성을 갖는 In-Bi-Sn계 합금을 용융하고 테이프캐스팅공정에 의하여 박판으로 제조하여 온도퓨즈용 저온가용합금 박판소재로 활용하는 가능성을 조사하였다. In-Bi-Sn계 용융합금은 기존의 박판제조공정보다 단순하고 생산성이 향상된 테이프캐스팅공정을 사용하여 박판화가 가능하다. 테이프캐스팅공정을 사용하여 얻은 62.5 wt%-In 20.0 wt%-Bi 17.5 wt%-Sn(융점 $92.4^{\circ}C$) 합금박판으로 휴대폰용 온도퓨즈시스템을 구성하여 $95^{\circ}C$에서 용락되는 기능이 나타남을 확인하였다. 이러한 공정은 폐In-Bi-Sn계 합금스크랩 처리에도 적용하여 합금조성과 박판두께를 적절히 조정하면 온도퓨즈시스템 가용합금 박판소재로 재활용할 수 있을 것으로 기대된다.

• Korea-Australia Rheology Journal
• /
• 제11권3호
• /
• pp.225-232
• /
• 1999

This study presents 1-dimensional simple model for sheet casting or rectangular fiber spinning process. In order to achieve this goal, we introduce the concept of force flux balance at the die exit, which assigns for the extensional flow outside the die the initial condition containing the information of shear flow history inside the die. With the Leonov constitutive equation that predicts non-vanishing second normal stress difference in shear flow, we are able to describe the anisotropic swelling behavior of the extrudate at least qualitatively. In other words, the negative value of the second normal stress difference causes thickness swelling much higher than width of extrudate. This result implies the importance of choosing the rheological model in the analysis of polymer processing operations, since the constitutive equation with the vanishing second normal stress difference is shown to exhibit the characteristic of isotropic swelling, that is, the thickness swell ratio always equal to the ratio in width direction.

• 마이크로전자및패키징학회지
• /
• 제23권2호
• /
• pp.11-18
• /
• 2016

This study focused on examining the possibility for recycling of Fe-Si electric sheet. We manufactured Fe-6.5Si mother alloy using by Fe-Si electric sheet scrap for transformer core materials. And then, soft magnetic alloy powder which diameter and shape were $45{\sim}150{\mu}m$ and sphere type was prepared by gas atomization process. As we compared to commercial Fe-6.5Si powder, its diameter distribution and microstructure of recycled powder was a similar. To investigate the possibility of reusing the soft magnetic composite sheet for electronics, recycled powder was treated to have a high aspect ratio (AR), and we finally obtained the 65~66 AR and $2.3{\mu}m$ thickness powder. To release the residual stress of powder, heat treatment was conducted under $300{\sim}400^{\circ}C$, $N_2$ gas. And then, soft magnetic sheet was made by tape casting process using by those powders. After the density and permeability of tape was measured, and we confirmed that the recycled Fe-Si electric sheet scrap was possible to reuse the soft magnetic materials of electronics.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.243-249
• /
• 2011

This study describes the feasibility of producing high-strength Al alloy sheet with a high solute content using a combined technique of twin-roll strip casting and asymmetric rolling. The Al sheet produced in this study exhibited excellent formability ($\overline{r}$ =1.0, $\Delta$r=0.16) and mechanical properties ($\sigma_{TS}$~305 MPa, $\epsilon$~33%), that, cannot be feasibly obtained via the conventional technique based on ingot casting and rolling. The structural origin of the observed properties, especially enhanced formability, was clarified by examining the evolution of textures associated with strip casting and subsequent thermo-mechanical treatments. Our evaluation of the mechanical properties and formability leads us to conclude that the combination of strip casting and asymmetric rolling is a feasible process for enhancing the formability of Al alloy sheets to the level beyond what the conventional techniques can reach.

• 마이크로전자및패키징학회지
• /
• 제24권1호
• /
• pp.1-8
• /
• 2017

Fe-9.8Si-6.0Al mother alloy was manufactured using by Fe-3.5Si recycled scrap and Si powder. And then, soft magnetic alloy powder of $D_{50}$ size and sphere type were prepared by gas atomization process. To obtain the soft magnetic powder of a high aspect ratio, in the first, we conducted the ball milling process for 8 hours. And heat treatment was performed under $650^{\circ}C$, 2 hours and $N_2$ atmosphere condition for reducing the residual stress of the powder. Based on these process, we made around $50{\mu}m$ diameter Fe-9.8Si-6.0Al powder, which morphology and shape was a similar to the commercial Fe-Si-Al powder. Finally, the soft magnetic sheets were prepared by tape casting process using by those powders. The permeability of the tape casting sheet was measured, and we confirmed the possibility of reusing to the soft magnetic materials of Fe-Si electric sheet scrap.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.158-168
• /
• 2001

Die design of die casting is composed of selection of cast alloy, design of die casting product, runner design and gate design, etc. In reality, however, die design of die casting has been performed by trial and error method, which cause economic and financial loss. Nowadays, several FEM(finite element method) and FDM(finite difference method) codes have been developed to analyze process of die casting, but this is just confined to an offer of limited information for die design of die casting. In this study, die design system for gate of die casting process has been developed to present algorithm for automation of die design, especially runner-gate system. In addition, specific rules for runner-gate system have been presented to avoid too many trials and errors with expensive equipment. It is possible for engineers to make automatic and efficient die design of die casting and it will result in reduction of expense and time to be required.

• 한국주조공학회지
• /
• 제35권3호
• /
• pp.62-66
• /
• 2015

Tape casting is an important forming operation used to prepare flat sheets in the various industries. In this study, Doctor Blade tape casting of In-based low melting point alloy was carried out. The purpose of this investigation was to determine the possibility of applying the Doctor Blade tape casting process to the manufacture of low melting point alloy sheets that can be used as thermal fusible parts of battery safety systems. In-based molten alloy that has a melting point of $95^{\circ}C$ was produced; it's viscosity was measured at various temperatures. The molten alloy was used as a slip in the caster of the Doctor Blade tape casting system. The effects of the molten alloy temperatures and carrier speeds on the produced sheet shape were observed. For the casting conditions of 1.5 cm slip height, $120^{\circ}C$ slip temperature, 0.05 mm blade gap and 60 m/min. carrier speed, an In-based alloy thin tape well shaped with 0.16 mm uniform thickness was continuously produced.