• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.112-115
• /
• 2015

In this study, the surface of ITO films was modified using $N_2-O_2$ molecular plasma, and the effects of oxygen concentration in the plasma on the ITO surface properties were investigated. Upon plasma treatment of ITO films, the surface roughness of ITO films seldom changed up to the oxygen concentration in the range of 0% to 40%, while the roughness of the films slightly changed at or above the oxygen concentration of 60%. The contact angle of water droplet on ITO films dramatically changed with varying oxygen concentration in the plasma, and the minimum value was found to be at the oxygen concentration of 20%. The plasma resistance at this condition exhibited a maximum value, and the change of resistance showed an inverse relationship compared to that of contact angle. From these results, it was conjectured that the chemical reactions in the sheath of the molecular plasma dominated more than the physical actions due to energetic ion bombardment, and also the plasma resistance could be used as an indirect indicator to qualitatively diagnosis the state of plasma during the plasma treatment.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.3
• /
• pp.94-101
• /
• 2008

A new convenient magnet array module is designed to investigate effects of magnetic field array on magnetron discharge characteristics. Magnetic field analysis showed good agreement of measured discharge region by a CCD device which has a high quantum efficiency over visible wavelength range. OES (optical emission spectroscopy) showed major emission peaks are from electronic transitions in 400 nm range and 800 nm range. Effects of driving voltage characteristics were analyzed in a point of electron drift trajectories and ionizing collision frequencies. Pulsed dc with a fast rising and falling time was analyzed to have potential to increase ionization collisions by putting a burst of hot electrons and to raise sheath potential. From measured voltage and current waveform, maximum of -1000 V peak was generated with $-400\;V_{rms}$ conditions. Possibility of a properly designed magnetron cathode was shown to be used as a melting device. Cu was successfully melted with power density of a several tens of $W/cm^2$.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.8 no.2
• /
• pp.151-157
• /
• 2003

Obtaining a sufficient amount of healthy keratinocytes from a small tissue is difficult. However, ORS cells can be a good source of epithelium since they are easily obtainable and patients do not have to suffer from scar formation at donor sites. Accordingly, the current study modified the conventional primary culture technique to overcome the low propagation and easy aging of epithelial cells during culturing. In a conventional primary culture, the average yield of human ORS tells is 2.↑ $\times$ 10$^3$cells/follicle based on direct incubation in a trypsin (0.1%)/EDTA(0.02%) solution for 15 min at 37$^{\circ}C$, however, our modified method was able to obtain about 6.9 $\times$ 10$^3$cel1s/follicle using a two-step enzyme digestion method involving dispase (1.2 U/mL) and a trypsin (0.1%)/EDTA (0.02%) solution. Thus, the yield of primary cultured ORS cells could be increasd three times higher. Furthermore, a total of 2.0 $\times$ 10$^{7}$ cells was obtained in a serum-free medium. while a modified E-medium with mitomycin C-treated feeder tells produced a total of 6.3 $\times$ 10$^{7}$ Cel1s over 17 days When Starting With 7.5 $\times$ 10$^4$cells. Finally, We Confirmed the effectiveness of our ORS tell isolation method by presenting their ability for reconstructing the bioartificial skin epithelium in vitro

• Applied Microscopy
• /
• v.31 no.2
• /
• pp.207-214
• /
• 2001

Anatomy and ultrastructure of the modifeid Krana pattern have been studied in succulent Salsola collina Pall. Cylindrical leaves exhibited the Salsoloid Kranz type containing two layers of peripheral chlorenchyma that surrounded the water storage cells and vascular tissues. Small veins were also peripherally arranged, but mostly embedded in the vicinity of the inner chlorenchma without the orderly arrangement of the concentric layering of bundle sheath and mesophyll cells. The current study mainly focused on the chlorenchyma tissue abutting such minor veins. The outer columnar layer exhibited features similar to the characteristics of palisade mesophyll cells, while the inner cuboid layer to the bundle sheath cells of a typical $C_4$ Kranz pattern. Cellular components of the inner chlorenchyma were centripetal and numerous, but starch-laden chloroplasts were rudimentary in the thylakoidal system. The outer chlorenchyma demonstrated normally developed chloroplasts having well-stacked thylakoids and plastoglobuli. Branched and complicated plasmodesmata frequently occurred in thick interfaces of the two layers, implying the active movement of the photosynthates between them. The present data were mostly congruent with one of the structural features of the C4 subtypes , NADP-ME type, reported in the $C_4$ pattern. The Kranz pattern encountered in this Salsola probably has been directly related to the structural modification that occurred during a functional adaptation to the $C_4$ photosynthesis.

• ALGAE
• /
• v.35 no.3
• /
• pp.213-224
• /
• 2020

The freshwater red algal genus Sheathia contains species with heterocortication (both bulbous and cylindrical cells covering the main axis) and homocortication (only cylindrical cells). When the genus was proposed, the species with heterocortication were revised, but all specimens with homocortication were assigned to Sheathia arcuata with the caveat that it may represent a species complex. Recent studies have described new species with homocortication and S. arcuata has been rendered paraphyletic. In the current study, new sequences of the rbcL and 5′ region of the cytochrome c oxidase subunit I markers were combined with previously published data to construct a robust phylogeny and circumscribe new species. Four new species, S. abscondita, S. californica, S. plantuloides, and S. transpacifica are proposed. Examination of morphological characters among homocorticate species show no diagnostic characters to distinguish among species, whereas S. plantuloides is only known from sporophytes (chantransia) so it lacks the typical morphological characters derived from the gametophytes for comparison. Although DNA sequence data would be needed to make a positive species identification, geography could be employed to narrow the identification to one or two species. The genus is geographically widespread having been recorded from oceanic islands and five continents, whereas the individual species typically occur on a single continent. With this study, the number of species recognized in Sheathia is raised to 17; seven heterocorticate and 10 homocorticate, making this genus one of the most species rich in the Batrachospermales. As well, the resulting phylogeny provides insights into the evolution of heterocortication in Sheathia.

• Journal of the Korean housing association
• /
• v.27 no.4
• /
• pp.13-22
• /
• 2016

The long term plan for apartment housing has a important role to make a decision making whether a repair work should be done or not. But, items for repair works are so various that field workers could not understand the context or plan the repair cost and time. These difficulties are drawn from the number of repair items, duplicated application and meaning, new material application and technology time-gap. Therefore, it needs to change or coordinate the repair items to improve the repair condition, reflecting the current material level or repair technologies. In this paper, it aimed at coordination of the repair items through the repair recording sheet which was surveyed in 22 metropolitan areas of Seoul, conducted between 2011 and 2014. The surveyed data are classified into six categories such as building exterior, building interior and so on, according to long term repair plan and the number of data are 1,918. It analyzed the appearing word for repair-concerned and compared the existing items of the long term plan. Items of building exterior are proposed as roof, exterior wall and painting. Building interior has a little meaning to propose the repair items. The water supply facilities are proper to keep the existing repair items. Items of the outdoor facilities could not need a sign board, drainage root and PVC sheath. Through this study, we can coordinate the repair items in apartment and provide the repair item and cost level.

• International Journal of Oral Biology
• /
• v.36 no.3
• /
• pp.135-141
• /
• 2011

Hertwig's epithelial root sheath (HERS) consists of bi-layered cells derived from the inner and outer dental epithelia and plays important roles in tooth root formation as well as in the maintenance and regeneration of periodontal tissues. With regards to the fate of HERS, and although previous reports have suggested that this entails the formation of epithelial rests of Malassez, apoptosis or an epithelial-mesenchymal transformation (EMT), it is unclear what changes occur in the epithelial cells in this structure. This study examined whether HERS cells undergo EMT using a keratin-14 (K14) cre:ROSA 26 transgenic reporter mouse. The K14 transgene is expressed by many epithelial tissues, including the oral epithelium and the enamel organ. A distinct K14 expression pattern was found in the continuous HERS bi-layer and the epithelial diaphragm were visualized by detecting the ${\beta}$-galactosidase (lacZ) activity in 1 week postnatal mice. The 2 and 4 week old mice showed a fragmented HERS with cell aggregation along the root surface. However, some of the lacZ-positive dissociated cells along the root surface were not positive for pan-cytokeratin. These results suggest that the K14 transgene is a valuable marker of HERS. In addition, the current data suggest that some of the HERS cells may lose their epithelial properties after fragmentation and subsequently undergo EMT.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.10
• /
• pp.1364-1370
• /
• 2014

Power system fault analysis has been based on symmetrical component method, which describes power system elements by positive, negative and zero sequence impedance. Obtaining accurate line impedances as possible are very important for estimating fault current magnitude and setting distance relay accurately. Especially, accurate calculation of zero sequence impedance is important because most of transmission line faults are line-to-ground faults, not balanced three-phase fault. Since KEPCO has started measuring of transmission line impedance at 2005, it has been revealed that the measured and calculated line impedances are well agreed within reasonable accuracy. In case of underground transmission lines, however, large discrepancies in zero sequence impedance were observed occasionally. Since zero sequence impedance is an important input data for distance relay to locate faulted point correctly, it is urgently required to analyze, detect and consider countermeasures to the source of these discrepancies. In this paper, development of pre/post processor to ATP (Alternative Transient Program) version of EMTP (Electro-Magnetic Transient Program) for sequence impedance calculation was described. With the developed processor ATP-cable, effects of ground resistance and ECC (Earth Continuity Conductor) on sequence impedance were analyzed.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.72-77
• /
• 2021

The radial distribution of etch rate was analyzed using the ion energy flux model in VHF-CCP. In order to exclude the effects of polymer passivation and F radical depletion on the etching. The experiment was performed in Ar/SF6 plasma with an SF6 molar ratio of 80% of operating pressure 10 and 20 mTorr. The radial distribution of Ar/SF6 plasma was diagnosed with RF compensated Langmuir Probe(cLP) and Retarding Field Energy Analyzer(RFEA). The radial distribution of ion energy flux was calculated with Bohm current times the sheath voltage which is determined by the potential difference between the plasma space potential (measured by cLP) and the surface floating potential (by RFEA). To analyze the etch rate uniformity, Si coupon samples were etched under the same condition. The ion energy flux and the etch rate show a close correlation of more than 0.94 of R² value. It means that the etch rate distribution is explained by the ion energy flux.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.4
• /
• pp.462-466
• /
• 2010

The purpose of this study is to evaluate the safety of a wire connector fabricated for the effective installation of a lighting fixture including its contact resistance, insulation resistance, withstanding voltage characteristics, etc., and to provide the basis for the analysis and judgment of PL(Product Liability) dispute by presenting a damage pattern due to a general flame and overcurrent. This study applied the Korean Standard (KS) for the incombustibility test of the connector using a general flame and performed an overcurrent characteristics test of the connector using PCITS (Primary Current Injection Test System). The contact resistance of the housing connector was measured using a high resistance meter and the insulation resistance was measured using a multimeter. In addition, a supply voltage of AC 1,500V for testing the withstanding voltage characteristics was applied to both ends of the connector. Measurement was performed on 5 specimens and the measured values were used as a basis for judgment. Since the connector is fabricated in the form of a housing, it can be connected and separated easily and has a structure that allows no foreign material to enter. In addition, since it has a structure that allows wires to be connected only when their polarity is identical, any misconnection that may occur during installation can be prevented. When the incombustibility test was performed by applying a general flame to the connector, it showed outstanding incombustibility characteristics and the blade and blade holder connected to the housing remained firmly secured even after the insulation sheath (PVC) was completely destroyed by fire. In addition, the mechanism of the damaged connecting wire showed a comparatively uniform carbonization pattern and it was found that some residual melted insulation material was attached to both ends. In the accelerated life test (ALT) to which approximately 500% of the rated current was applied, the connector damage proceeded in the order of white smoke generation, wire separation, spark occurrence and carbonization. That is, it could be seen that the connector damaged by overcurrent lost its own metallic color with traces of discoloration and carbonization. The contact resistance of the connector at a normal state was 2.164mV/A on average. The contact resistance measured after the high temperature test was 3.258mV/A. In addition, the insulation resistance after the temperature test was completed was greater than $10G\Omega$ and the withstanding voltage test result showed that no insulation breakdown occurred to all specimens showing stable withstanding voltage and insulation resistance characteristics.