• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.635-641
• /
• 2011

The effect of high shear speed on shear force, shear energy and fracture surface was investigated for the solder joint of a $Sn-_{3.0}Ag-_{0.5}Cu$ ball. For both ENIG and OSP pads, the shear force increased with an increase in shearing speed to 0.3 m/s. However, for an ENEPIG pad, the shear force increased with an increase in shear speed to 0.6 m/s and kept almost constant afterward. The shear energy decreased with an increase in shearing speed for ENIG and OSP pads. For the ENEPIG pad, however, the shear energy almost remained constant in a shearing speed range 0.3-3.0 m/s. The fracture mode analysis revealed that the amount of brittle fracture for the ENIG and the OSP pads increased with shearing speed, and a complete brittle fracture appeared at 1.0 m/s for ENIG and 2.0 m/s for OSP. However, the ENEPIG pad showed only a ductile fracture until 0.25 m/s, and a full brittle fracture didn't occur up to 3.0 m/s. The fracture mode matched well with the shear energy. The results from the high speed shear test of SAC305 were similar to those of SAC105.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.237-242
• /
• 2011

The effect of shearing speed on the shear force and energy of Sn-0Ag-0.5Cu solder ball was investigated. Various UBM (under bump metallurgy)'s on Cu pads were used such as ENEPIG (Electroless Nickel, Electroless Palladium, Immersion Gold; Ni/Pd/Au), ENIG (Electroless Nickel, Immersion Gold; Ni/Au), OSP (Organic Solderability Preservative). To fabricate a shear test specimen, a solder ball, $300{\mu}m$ in diameter, was soldered on a pad of FR4 PCB (printed circuit board) by a reflow soldering machine at $245^{\circ}C$. The solder bump on the PCB was shear tested by changing the shearing speed from 0.01 m/s to 3.0 m/s. As experimental results, the shear force increased with a shearing speed of up to 0.6 m/s for the ENIG and the OSP pads, and up to 0 m/s for the ENEPIG pad. The shear energy increased with a shearing speed up to 0.3 m/s for the ENIG and the OSP pads, and up to 0.6 m/s for the ENEPIG pad. With a high shear speed of over 0 m/s, the ENEPIG showed a higher shear force and energy than those of the ENIG and OSP. The fracture surfaces of the shear tested specimens were analyzed, and the fracture modes were found to have closer relationship with the shear energy than the shear force.

• 수산해양기술연구
• /
• 제16권2호
• /
• pp.61-67
• /
• 1980

Previously, we had experimented on the model of stow net under the various combination including water velocity, spherical floats and elevating floats with the shearing hoods instead of the upper beam, however we couldn't concern with their characteristics. Spherical floats maintain their buoyancy at the same level when the speed increases, only the drag increases and effects some reduction in the fishing height. To eliminate this shortcoming, floats have to some hydrodynamic lifting force which increases with increasing speed. Phillips float with a dish-shaped metal plate welded on at the lower part and synthetic upthrusting float were used for the experiment to compare with their characteristics. Six kinds of model shearing hood depend on the angle of attack were used to test the characteristic of the shearing hood. According to their results, when the angle of attack is 30\ulcorner, the lift and drag coefficient reveal 1. 36, 0.84 respectively. And also experimented on the 5X8cm shearing hood to investigate the suitability for the model stow net.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집(한일합동학술편); 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.759-764
• /
• 1987

The design and application of optimal control technique to the rotary shearing system is mentioned in this paper. To maximize the accuracy in both shearing length and blade speed at shearing, time-varying gain patterns for closed loop control are designed on the basis of fixed terminal time constrained optimal regulator. The performance accuracy in real application has greatly improved than the conventional way of shearing control.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.580-585
• /
• 2009

The effects of shear speed and tip height on the high speed shear test of Sn-3.0wt.%Ag-0.5wt.%Cu ball joints were investigated. Solder balls of $450{\mu}m$ in diameter were reflowed at $245^{\circ}C$ on a FR4 PCB (Printed Circuit Board) in order to obtain a sample for the high-speed shear test. The UBM was comprised of Cu/Ni/Au, and the shear speed and tip height varied from 0.5 to 3.0 m/s, and from 10 to $135{\mu}m$, respectively. According to the experimental results, faster shear speed enhanced the shear strength of the solder joints, regardless of the tip height. The fraction of ductile (solder) fracture decreased when the shearing speed was raised from 0.5 to 3.0 m/s. With an increasing tip height from 10 to 50 and $135{\mu}m$, the fracture mode changed from pad lift to mixed (ductile and brittle) and ductile fracture, respectively, while the shearing energy also increased in the same order. The shear energy had a proportional relationship with the fraction of the solder fracture.

• 마이크로전자및패키징학회지
• /
• 제18권1호
• /
• pp.35-39
• /
• 2011

고속전단시힘의 표준화를 위한 기초 연구의 일부로 Sn-3.0wt%Ag-0.5wt%Cu 솔더 볼의 고속전단특성에 대한 연구를 수행 하였다. 고속전단 시험편 제작을 위해 직경 450 ${\mu}m$의 솔더 볼을 FR4 PCB (Printed Circuit Board) 위에 장착한 후 $245^{\circ}C$ 온도에서 리플로 솔더링을 행하였다. PCB 상의 금속 패드로는 ENIG (Electroless Nickel/mmersion Gold, i.e Cu/Ni/Au)와 OSP (Organic Solderability Preservative, Cu 패드)를 사용하였다. 고속전단 속도는 0.5~3.0 m/s 범위, 전단 팁의 높이는 10~135 ${\mu}m$ 범위에서 변화시켰다. 실험결과로서, OSP 패드의 경우 전단 팁 높이 증가에 따라 연성 파괴가 증가하였으며, 전단속도 증가에 따라 연성파괴는 감소되었다. ENIG 패드의 경우에도 전단 팁 높이 증가에 따라 연성 파괴가 증가하였다. 전단 팁 높이 10 ${\mu}m$(볼 직경의 2%)는 패드 박리 파괴가 대부분이어서 전단파면 관찰에는 부적절한 높이였다. 고속전단에너지는 OSP 및 ENIG 패드 모두 전단 팁 높이 증가에 따라 증가하는 경향을 보였다.

• 산업식품공학
• /
• 제13권1호
• /
• pp.70-73
• /
• 2009

The yield stress of stirred yogurt was measured by the vane viscometer at different pre-shearing conditions, such as pre-shear speed, pre-shear time, and wait time, and temperature (12-38${^{\circ}C}$). The yield stress ranged from ~17.6 to 10 Pa and from 34.2 to 11.9 Pa, depending on the pre-shearing conditions and temperature, respectively. The preshear speed and the wait time significantly affected the yield stress. The temperature dependence of the yield stress was described by the Eyring's kinetic model. The linear function of the temperature on the yield stress was limited at the 22${^{\circ}C}$, and at the above 22${^{\circ}C}$, the yield stress was maintained to be a constant (~12.5 Pa).

• 소성∙가공
• /
• 제30권4호
• /
• pp.195-200
• /
• 2021

In this study, we investigated the dominant processing variables that would influence the microstructural development of AA6061 deformed by differential speed rolling (DSR) at ambient temperature. For this purpose, we carried out a series of DSR on the samples to investigate the effects of roll speed ratio, sample rotation, and number of operation under specific rotation. Among these, the condition with a height reduction of 75% at a speed ratio of 1:4 through rotation along rolling direction (RR) displayed the pronounced results of more homogenous matrix-structure and superior mechanical properties than the others tested in this study. This was mainly due to the cross shearing of macro-shear pattern in segment where dynamic recrystallization took place with ease throughout the sample. Thus, an average microhardness value of 101 Hv was obtained in the present sample deformed by 4-pass DSR with RR where macro cross-shearing was effectively applied.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1647-1650
• /
• 2008

The moyamoya disease is a type of cerebrovascular disease which produces thin abnormal blood vessels like haze in the brain base because the end of internal carotid artery which supplies about 80% of blood is blocked. Regarding this moyamoya disease, the shearing stress and thrombus generation are mentioned as its main causes. This study three-dimensionally implemented the ICA, ACA, and MCA parts of the cerebrovascular configuration related to the moyamoya disease, and analyzed the hydrodynamic phenomenon with the commercial program ADINA. In particular, the correlations between shearing stress and speed distribution according to the branch angle of ACA and MCA. A numerical analysis found that the greater the branch angle of ACA and MCA, the lower the shearing stress and the greater the stationary area of the flow.. Put Abstract text here.

• 한국생산제조학회지
• /
• 제21권5호
• /
• pp.726-732
• /
• 2012

Pipe and Pressure Vessels that is used in power plant and chemical industry have many Internal Defects that is corrosion caused by the flow of fluid. These Internal Defects that have possibility of explosion are very dangerous because it can not see from the outside. This days many companys using NDT method to find an Internal Defect. Most of the NDT methods have limitations that are constraint of shape and materials. But Sheargoraphy have many advantages compared conventional NDT method. It has very fast measuring speed, non-destructive and non contacting measurement. As well as it hasn't constraint of shape and materials. As a paper on the analysis of measurement of error, the important factors were the Shearing Amount and pressure, and discovered measurement of the Internal Defect of the object by using shearography. The optimal Shearing Amount and pressure was discovered and utilized.