• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.12
• /
• pp.2394-2402
• /
• 2017

The frequency selective fading by multipaths determines a performance of underwater acoustic communication system in shallow littoral ocean. In this study, a characteristics of underwater acoustic channel and performance of multi-carrier system is evaluated in littoral ocean with a 50m deep water, an effective wave height of 0.5m and sandy mud bottom near Busan city. A multipath delay spread and time and frequency domain are presented as a function of a transmitter-to-receiver range. A bit-error-rate of a 5 channel 4FSK(Frequency Shift Keying) with a transmission rate of 1kbps, is examined and RS(Reed-Solomon) code is also adopted to remove a burst error due to time domain fading. A number of multipath are less than four and a bit-error-rate is decreased as an increase of a transmitter-to-receiver range which gives a congestion of multi-paths resulting in a decrease of time and frequency domain fading. The measured bit-error-rate is about 10-4 at greater than 600m of transmitter-to-receiver range.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.8-17
• /
• 2018

A large urban region in Bangkok, Thailand is often inundated due to shallow water floods along the paved roads that have poor drainage facilities, and that can cause urban flooding. Existing methods, including using sand bags are not effective to prevent flooding in urban areas where the amount of sand is not sufficient. Thus, it is necessary to install artificial flood defense structures. However flooding and overflow defense equipment, which was developed in some advanced nations in Europe and in the USA, is highly expensive and complex construction methods are needed, therefore they are not suitable to be used in Southeast Asia. Thus, it is necessary to develop a flood rapid defense system(FRDS), which is inexpensive and simple to build, but is also highly functional. Thus, this study developed an FRDS that can be applied to Southeast Asia through the careful study of FRDS overviews, an analysis on the development trends in Korea and overseas, and the proposal of development needs and directions of the region. For the system developed, Korean Standards(KS) performance evaluations on leakage ratio deformation tests and impact resistance tests were conducted at the Outdoor Demonstration Test Center(Seosan) in the Korea Conformity Laboratories(KCL) and the system satisfied the standards of KS F 2639(leakage and deformation test) and KS F 2236(impact resistance test). The present study results can not only be applied to urban floods in Southeast Asian nations to cope with flood-related disasters, but also be utilized in flood prone regions and for major facilities in Korea. They can also induce scientific and pro-active responses from major local governments and facility management organizations in relation to urban floods.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.4
• /
• pp.269-282
• /
• 2006

We numerically studied tsunami propagation characteristics through Korean Straits based on nonlinear shallow water equation, a robust wave driver of the near field tsunamis. Tsunamis are presumed to be generated by the earthquake in Tsuhima-Koto fault line. The magnitude of earthquake is chosen to be 7.5 on Richter scale, which corresponds to most plausible one around Korean peninsula. It turns out that it takes only 60 minutes for leading waves to cross Korean straits, which supports recently raised concerns at warning system might be malfunctioned due to the lack of evacuation time. We also numerically obtained the probability of tsunami inundation of various levels, usually referred as tsunami hazard, along southern coastal area of Korean Peninsula based on simple seismological and Kajiura (1963)'s hydrodynamic model due to tsunami-generative earthquake in Tsuhima-Koto fault line. Using observed data at Akita and Fukaura during Okushiri tsunami in 1993, we verified probabilistic model of tsunami height proposed in this study. We believe this inundation probability of various levels to give valuable information for the amendment of current building code of coastal disaster prevention system to tame tsunami attack.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.185-194
• /
• 2012

Deepwater oil is becoming more attractive because most onshore and shallow water oil is developing or developed. With the on-going trend to deepwater oil developments, flow assurance problems which prevent oil flow from reservoir to processing facilities are becoming an issue because deposited material can be occurred in case oil is exposed to very different environment from reservoir. Wax deposition which is one of flow assurance problems can be a major technical and economic issue because it is very sensitive to temperature. In order to predict and mitigate wax problems, the precise measurement of wax appearance temperature (WAT) which is the starting temperature of wax precipitation is very important. Various methods have been suggested for WAT measurement of opaque oil because there is no standard method for opaque oil. In this study, the WAT of opaque oil samples was measured using viscosity measurement method, differential scanning calorimetry, filter plugging method, and pressurized filter plugging method. Wax deposition test and high temperature gas chromatography analysis were applied to verify measured WAT. As a result of study, the WAT of opaque oils was successfully measured and verified. If WAT measurement methods of opaque oil related to oil characteristics is systematized using the results of this study, it can be a valuable tool for WAT measurement of opaque oil and flow assurance related to wax deposition.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.30 no.2
• /
• pp.69-83
• /
• 2018

The South China Sea (SCS) is a typical marginal sea characterized with the deep basin, shelf break, shallow shelf, many straits, and complex bathymetry. This study investigated the tidal characteristics and propagation, and reproduced typhoon-induced storm surge in this region using the regional real-time tide-surge model, which was based on the unstructured grid, resolving in detail the region of interest and forced by tide at the open boundary and by wind and air pressure at the surface. Typhoon Haiyan, which occurred in 2013 and caused great damage in the Philippines, was chosen as a case study to simulate typhoon's impact. Amplitudes and phases of four major constituents were reproduced reasonably in general, and the tidal distributions of four constituents were similar to the previous studies. The modelled tide seemed to be within the acceptable levels, considering it was difficult to reproduce the tide in this region based on the previous studies. The free oscillation experiment results described well the feature of tide that the diurnal tide is prevailing in the SCS. The tidal residual current and total energy dissipation were discussed to understand the tidal and sedimentary environments. The storm-surge caused by typhoon Haiyan was reasonably simulated using this modeling system. This study established the regional real-time barotropic tide/water level prediction system for the South China Sea including the seas around the Philippines through the validation of the model and the understanding of tidal characteristics.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.2
• /
• pp.104-115
• /
• 2013

In a shallow water waveguide, reverberation signals and their Doppler effects form the primary limitation on sonar system performance. Therefore, in the reverberation-limited environment, it is necessary to estimate the reverberation level to be encountered under the conditions in which the sonar system is operated. In this paper, high-frequency reverberation model capable of simulating the reverberation signals received by a high-speed moving source in a range independent waveguide is suggested. In this model, eigenray information from the source to each boundary is calculated using the ray-based approach and the optimizing method for the launch angles. And the source receiving position changed by the moving source is found by a scattering path-finding algorithm, which considers the speed and direction of source and sound speed to find the path of source movement. The scattering effects from sea surface and bottom boundaries are considered by APL-UW scattering models. The model suggested in this paper is verified by a comparison to the measurements made in August 2010. Lastly, this model reflects well statistical properties of the reverberation signals.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.561-568
• /
• 2020

Wave measurements using X-band radar have many advantages compared to other wave gauges including wave-rider buoy, P-u-v gauge and Acoustic Doppler Current Profiler (ADCP), etc.. For example, radar system has no risk of loss/damage in bad weather conditions, low maintenance cost, and provides spatial distribution of waves from deep to shallow water. This paper presents new methods for estimating significant wave heights of X-band marine radar images using Artificial Neural Network (ANN). We compared the time series of estimated significant wave heights (Hs) using various estimation methods, such as signal-to-noise ratio (${\sqrt{SNR}}$), both and ${\sqrt{SNR}}$ the peak period (TP), and ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k). The estimated significant wave heights of the X-band images were compared with wave measurement using ADCP(AWC: Acoustic Wave and Current Profiler) at Hujeong Beach, Uljin, Korea. Estimation of Hs using ANN with 3 parameters (${\sqrt{SNR}}$, TP, and Rval > k) yields best result.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.22 no.3
• /
• pp.88-102
• /
• 2017

Long-term changes in bathymetry and grain size of surface sediments were investigated for understanding depositional sedimentary environments in the channelized Yeongsan River Estuary, Korea. The results revealed that an average depth of the estuary had decreased up to 2.1 m from 1982 to 2006, while it had increased to 0.3 m from 2006 to 2012. The rapid decrease of the water depth from 1982 to 2006 was due to the vast deposition of mud caused by the change of water course and flow velocity after the estuary was dammed. Meanwhile the increase of the water depth from 2006 to 2012 may be associated with multiple erosional processes, including a dredging at the southern part of the estuary and other erosions from the dike sluice expansion work. Considering the water-depth change and tidal-level variation in the study area, an depositional rate in the estuary is estimated to be 8~9 cm/yr for the last 2 decades (1982~2006). The sediments of Yeongsan River Estuary are largely composed of silt-clay mixtures: overall, silt is distributed mainly in the shallow area of the estuary edge, while clay is confined to the deep area of the estuary center. Mean grain size of the sediments is 6.0 Ø on average in 1997, 7.8 Ø on average in 2005 and 7.7 Ø on average in 2012, respectively, suggesting that the sediments became finer due to the increase of silt and clay contents in 1997~2005. Furthermore, several lines of evidences, including the comparison between the amounts of the sediment influx discharged from the Yeongsan River and the sediments in the estuary, and the changes in distribution pattern of silt and clay contents implying that they moved from offshore to estuary dike, indicate that the mud sediments are originated mainly from the offshore, not from the river.

• International Union of Geodesy and Geophysics Korean Journal of Geophysical Research
• /
• v.25 no.1
• /
• pp.57-81
• /
• 1997

Numerical prediction of nocturnal thermal high in summer of the 1995 near Taegu city located in a basin has been carried out by a non-hydrostatic numerical model over complex terrain through one-way double nesting technique in the Z following coordinate system. Under the prevailing westerly winds, vertical turbulent fluxes of momentum and heat over mountains for daytime hours are quite strong with a large magnitude of more than $120W/\textrm{m}^2$, but a small one of $5W/\textrm{m}^2$ at the surface of the basin. Convective boundary layer (CBL) is developed with a thickness of about 600m over the ground in the lee side of Mt. Hyungje, and extends to the edge of inland at the interface of land sea in the east. Sensible heat flux near the surface of the top of the mountain is $50W/\textrm{m}^2$, but its flux in the basin is almost zero. Convergence of sensible heat flux occurs from the ground surface toward the atmosphere in the lower layer, causing the layer over the mountain to be warmed up, but no convergance of the flux over the basin results from the significant mixing of air within the CBL. As horizontal transport of sensible heat flux from the top of the mountain toward over the basin results in the continuous accumulation of heat with time, enhancing air temperature at the surface of the basin, especially Taegu city to be higher than $39.3^{\circ}C$. Since latent heat fluxes are $270W/\textrm{m}^2$ near the top of the mountain and $300W/\textrm{m}^2$ along the slope of the mountain and the basin, evaporation of water vapor from the surface of the basin is much higher than one from the mountain and then, horizontal transport of latent heat flux is from the basin toward the mountain, showing relative humidity of 65 to 75% over the mountain to be much greater than 50% to 55% in the basin. At night, sensible heat fluxes have negative values of $-120W/\textrm{m}^2$ along the slope near the top of the mountain and $-50W/\textrm{m}^2$ at the surface of the basin, which indicate gain of heat from the lower atmosphere. Nighttime radiative cooling produces a shallow nocturnal surface inversion layer with a thickness of about 100m, which is much lower than common surface inversion layer, and lifts extremely heated air masses for daytime hours, namely, a warm pool of $34^{\circ}C$ to be isolated over the ground surface in the basin. As heat transfer from the warm pool in the lower atmosphere toward the ground of the basin occurs, the air near the surface of the basin does not much cool down, resulting in the persistence of high temperature at night, called nocturnal thermal high or tropical night. High relative humidity of 75% is found at the surface of the basin under the moderate wind, while slightly low relative humidity of 60% is along the eastern slope of the high mountain, due to adiabatic heating by the srong downslope wind. Air temperature near the surface of the basin with high moisture in the evening does not get lower than that during the day and the high temperature produces nocturnal warming situation.

• Economic and Environmental Geology
• /
• v.9 no.1
• /
• pp.1-11
• /
• 1976

It is believed that geological survey, drilling and geophysical survey which was carried out on Tertiary deposits in Pohang is a valuable but through the studying of many Tertiary sediments in Japan discovered many questions on analysis of final report prepared by National geological survey. The main reason is: 1. The seismic sound velocity which have regulated in the final report prepared by geological survey for Tertiary deposits in Pohang was 1,500-2,000m/sec in spite of oil bearing sediments of same age in Japan are 2,000-3,800m/sec. These may means the requirement of reconsideration of seismic velocity for Tertiary deposits in Pohang and required to have a dipper drilling. 2. Stratigraphically, geophysically, and paleontologically, the Tertiary deposits in Pahang land area is similar with that of Nishiyama-Hunakawa formations of Akita oil field in Japan. Nishiyama-Hunakawa formation is the main oil bearing formation in Japan. 3. Those valcanic rock including andestitic rock and liparitic rock which have extensively distributed over either at land area or at sea bottom, assumed by geological survey as the base of Tertiary sediments. But in case of Japan many oil bearing deposits are in over laid by these kind of volcanic rock. Therefore a possible of same condition with Japan is presumable on Tertiary sediments in Pohang. 4. It is believed that the Tertiary sediments of land area in Pohang is the extension of offshore basin but is wandering that the final report submitted by geologic survey have not remain any word on report of ECAFE discribed so much problematics as followed: A. Although it was assumed that no great thickness exceeding 1,000 meters, or major structures would be encountered in the Tertiary offshore sequence, it was hoped that shallow hydrocarbon deposits might be found, because these sediment are lithologically similar to those of the same age in the producing area of the northwest Honshu region of Japan where hydrocarbon are extracted from depths of only 500 to 600 meters. B. Four possible hydrocarbon trap conditions are represented in the survey area: anticlinal folds, faults, pinch outs, along the igneous basement and lateral facies changes. C. Most of the prime possible reservoir area are beyond the 50 meter water depth mark, except for the structures in Yonil Bay. D. Despite the shallowness of the offshore basin, sufficient trap condition exist in the area to warrant further exploration for hydrocarbon. 5. All of the problems mentioned above have gave us a strong reasons to have us hesitating to make a final conclusion on Tertiary problems in Pohang, before to have a drill to a depth to 3,000 meters or more whatever it is the Tertiary or a Mesozoics below 1,000 meters.