• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.483-488
• /
• 2002

Noise has become an environmental pollution that affects most peoples' health, comfort or general well being. there are many sources of noise, but one of them clearly dominates road traffic noise. It has traditionally been associated with engine and exhaust noise of vehicles. However the emission and propagation of noise from these sources were partly reduced, while at the same time the noise emission from the tire/road interaction on a relative scale became more and more prominent Generally, Portland cement concrete(PCC) pavements have the advantage of durability and superior surface friction when compared to most dense-graded asphalt. However, It is known that PCC pavements create more noise than asphaltic surfaces due to the noise from interaction of tire and pavement surface. Therefore, recent research has shown some new concrete pavement textures to be worth further examination. So in this paper, we considered the 9 types of low noise concrete pavements to evaluate tire/pavement noise.

• 한국대기환경학회지
• /
• 제12권5호
• /
• pp.523-528
• /
• 1996

Aerosol Particles were collected in a heaby traffic region in pusan. Samples were collected in two size fractions with a two-stage sampler during the day and the night. Elemental concentrations of these aerosol particles were determined by a PIXE(Proton Induced X-ray Emission) analysis method. The results suggest that the elements originating mainly from natural sources such as Si, Ca, Fe, Cl, and K are dominent in the coarse fraction, but the elements such as S, Pb, Br, and Zn are dominent in the fine fraction. Br/Pb ratio are evaluated in both coarse and fine size fraction, and which are mainly emitted automobile sources. The study further also discussed other Br/Pb ratio related works described elsewhere. Sulfur in the fine fraction was continuously increased during the sampling period without time variation.

• Journal of Information Display
• /
• 제6권4호
• /
• pp.35-39
• /
• 2005

In this paper, we investigate the oxide cathodes for the development of reliable electron sources. Poisoning in oxide cathodes is one of the serious problems in achieving reliable electron emission. In particular, early poisoning induces poor life performance as will be demonstrated herein. The survivability of electron emission sources is significantly improved by high doping of high-speed activator. The robust oxide cathodes with 0.17 % Mg operating at about 1,050 K are expected to work for very long times (>100,000 hours). We suggest that this key idea will contribute to solving the basic problems in oxide cathodes such as poisoning or ion bombardment for high power or high frequency applications of electron sources.

• International Journal of Automotive Technology
• /
• 제4권1호
• /
• pp.21-30
• /
• 2003

In this paper a systematic test procedure for evaluation of road-induced noise of a vehicle and guidelines for each test are presented. Also, a practical application of the test procedure to a small SUV is presented. According to the test procedure, all the tests were performed to evaluate road-induced booming noise that is in low frequency range. First of all the information on characteristics of road-induced noise was obtained through baseline test. Coupling effects between body structure and acoustic cavity of a compartment were obtained by means of modal tests for a structure and an acoustic cavity. Local stiffness of joint areas between chassis system and car-body was determined by test for measurement of input point inertance. Noise sensitivities of body joints to operational forces were obtained through test for measurement of noise transfer functions. Operational deflection shapes made us analyze behaviors of chassis system under running condition and then find sources of noise due to resonance of the chassis system. Finally, Principal Component Analysis and Transfer Path Analysis were utilized to investigate main paths of road-induced noise. In order to evaluate road-induced booming noise exactly, all of tests mentioned above should be performed systematically.

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.9-17
• /
• 2014

PURPOSES : The purpose of this study is to assess removal efficiency of non-point pollutants and applicability for non-point pollutant reduction facilities by conducting the demonstration project operation. METHODS : In order to analyze removal efficiency of non-point pollutants for facilities such as a grassed swale, a small constructed wetland, a free water surface wetland, a horizontal sub-surface flow wetland, and a sand filtration, the field data including specifications of facilities, rainfall, inflow and runoff rainfall effluent etc. was acquired after occurring rainfall events, and the acquired data was analyzed for removal efficiency rate to assess road non-point pollutants facilities using event mean concentration (EMC) and summation of load (SOL) methods. RESULTS : The results of analyzing rainfall effluent, non-point pollutant sources showed that total suspended solid (TSS), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total nitrogen (TN), total phosphorus (TP), chrome (Cr), zinc (Zn), and lead (Pb) can be removed through non-point pollutant reduction facilities by 60.3% ~ 100%. Especially removal efficiency of TSS, COD and BOD is relatively higher than removal efficiency of other non-point pollutant sources in all kind of non-point pollutant facilities. CONCLUSIONS : Based on the result of this study, even though natural type of non-point pollutant reduction facilities for roads occupy small areas comparing with drainage basin areas, most of non-point pollutant sources would be removed through the facilities.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.84-92
• /
• 1997

Among the various sources of vehicle interior noise, this paper concerns the road induced noise ; the identification of its transfer path by using experimental method. Multiple input and single output model is taken as a noise generation model. Because it is impossible to measure the road imput forces directly, the acceleration signals are measured on four axle;three directions for each point. By considering the cross correlations of input signals, four uncorrelated source groups are taken. Multiple coherence function is employed to investigate the contribution of each group. In addtion, to identify the detailed path through the suspension systems, the contributions of all possible paths are ranked by using the coherence functions between interior noise and the relative accelerations of connections such as bushings and mountings. Measurements are performed with passenger vehicle traveling on concrete and asphalt roads at 60㎞/h.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.1-4
• /
• 2008

Prediction models currently being used for road traffic noise in apartment are equation of NIER, HW-NOISE of Korea Expressway Corporation, FHWA of United States, CRTN of United Kingdom, NMPB of France, ASJ RTN-Model 2003 of Japan and ISO 9613-1, 2 as a international standard. ISO 9613 species an engineering method for calculating the attenuation of sound during propagation outdoors in order to predict the levels of environmental noise at a distance from a variety of sources. This study, prior to investigation of every prediction methods listed above, aims to examine the model internationally standardized and to establish a reference for the prediction of road traffic noise in apartment.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.613-617
• /
• 2007

Noise maps of a city in Korea have been made using commercial noise map softwares by measuring the basic data in the city. The result in this study will be used to evaluate the environmental impact of noise from various noise sources and to implement the Korean noise map standard.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.980-985
• /
• 2002

Several tests are performed to evaluate road booming noise. Baseline test delivers the information of road noise characteristics. Coupling effect between structure and acoustics is obtained from the mode shapes and the natural frequencies by the modal test. Equivalent stiffness at joint areas between chassis and car-body system can be determined by the input point inertance test. Noise sensitivity of body mounting point of a chassis part can be obtained from the noise transfer function test with input point inertance test. Operational deflection shape makes us analyze the actual vibration modes of the chassis system under actual loading and find noise sources very easily. finally, the transfer function analysis is used to identify noise paths through the chassis system. However, all of the tests above mentioned must be performed to evaluate road booming noise. The objectives and the procedures of the tests are described in this paper. Also, the guideline for efficient road noise evaluation test can be found.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.264-267
• /
• 2008

Relationship between exposure to combined noise sources and community annoyance have been investigated. Social surveys were conducted in urban spaces near the construction site with road traffics. The question relating to noise annoyance was answered on an 11-point numerical scale and 5-point verbal scale according to ISO 15666. The questionnaire also contained demographic factors, interference with daily activities, health-related symptoms, and noise sensitivity. Noise levels were measured in terms of A-weighted equivalent level ($L_{Aeq}$), and noise mapping technique was applied to predict the noise levels of urban spaces. Synthesis curves for the relationship between noise levels and percentage highly annoyed for combined noise sources were derived, and compared to the curves from a single noise source.