• Current Optics and Photonics
• /
• v.2 no.3
• /
• pp.286-290
• /
• 2018

We investigated the dependence of the retardation dispersion on the polarization direction of ultraviolet (UV) light during the photopolymerization of self-organized smectic reactive mesogen (RM) molecules. RM retarder film that was photopolymerized with UV light linearly polarized parallel to the layer plane showed negative dispersion (ND) of retardation for a wide range of UV polymerization temperatures. On the other hand, film that was photopolymerized with unpolarized UV light showed negative dispersion in a narrow range of UV polymerization temperatures. With a certain UV polymerization temperature, the dispersion of retardation was converted from positive to negative, depending on the UV polarization.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.435-436
• /
• 2007

In general, Single gap transflective FFS display has an in-cell retarder (ICR) between reflective electrode and liquid crystal (LC) layer. Therefore, Operating voltage is highly increased due to this thick dielectric material. But, we also knew the phenomenon that the increasing rate of Vop is different whether the 1st common electrode was composed of plate type or slit type. In this paper, the common electrode in transmissive part was composed of slit type which had less steepness effect of the V op and in reflective part was composed of plate type. The rubbing angle of reflective part can be adjusted properly to match the voltage dependent transmittance and reflectance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.199-200
• /
• 2023

This paper presents a study on the selection of optimal mix proportions for producing lightweight pre-foam concrete as a substitute for Autoclaved Lightweight Concrete (ALC) without the accelerated curing. The study was conducted using a rapid hardening binder made from by-products of the steel industry as the primary raw material. The experimental results established the optimal mix proportions, which included retarder content, water/binder ratio, foam content, and fiber inclusion amount, for the production of lightweight foam concrete. The optimal mix proportion was determined to have a retarder content at the minimum amount required to secure the working time, W/B of 35%, a foam content limited to 65% or less, and a fiber inclusion amount of 0.05% or less.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.02a
• /
• pp.197-198
• /
• 2006

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.761-764
• /
• 2008

Most of ready-mixed concrete plants have the problem of construction waste sludge, which pollutes environment and causes economic loss due to the discard and increasing the cost of concrete. Thus, a recycling of the cement sludge has been strongly desired as one of their solution. This research is to the study on the recycling of the cement sludge, especially the study on the hydration control by the sodium gluconate as a set-retarder. The set-retarder can delay the hydration of the cement included in the sludge water, so that the sludge water can be substituted with some of new cement without the property of the cement. And it invests the effect of the sodium gluconate to the hydration of the cement in suspension. The degree of hydration of cement may be controlled by adding the sodium gliconate. The hydration delay time is observed that depends on the concentration of residual sodium gloconate, not how long the cement has been hydrated before the addition of the sodium gluconate.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.02a
• /
• pp.324-325
• /
• 2005

• Magazine of the Korea Concrete Institute
• /
• v.23 no.2
• /
• pp.47-51
• /
• 2011

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.22-29
• /
• 2006

On purpose to reduce accumulated moisture and to prevent moisture condensation in a light-frame wall, thermal characteristics and moisture behaviors were investigated for four different wall assemblies; a) typical wall, b) addition of vapor retarder between the insulation and the gypsum board, c) addition of air gap for natural ventilation behind the siding, d) composition with b) and c). Each wall was tested under two climate conditions; 1) $20^{\circ}C$, 50% RH (indoor) and $30^{\circ}C$, 85% RH (outdoor), 2) $30^{\circ}C$, 85% RH (indoor) and $20^{\circ}C$, 50% RH (outdoor).The results showed that the typical wall assembly had poor resistance against moisture intrusion from the inside of building. Outdoor and indoor humidity caused the moisture condensations on the inside of the siding and the back surface of the sheathing respectively. The addition of a vapor retarder did not give significant improvement in preventing the moisture intrusion.

• Korean Journal of Optics and Photonics
• /
• v.25 no.3
• /
• pp.150-154
• /
• 2014

The conditions under which a composite retarder consisting of two different retardation plates can be operated as a tunable quarter-wave plate are derived. The explicit expressions for the azimuthal angle of a linear polarizer and those of two retardation plates to generate circularly polarized light are presented as a function of retardation angles. Those expressions for the azimuthal angles derived using the Jones matrix formalism are verified as identical to the expressions derived from the analysis of the trajectory on a Poincar$\acute{e}$ sphere. A couple of examples are presented for generating circularly polarized light when two identical retardation plates are used.

• Elastomers and Composites
• /
• v.13 no.4
• /
• pp.277-281
• /
• 1978

1. A good retarder reacts fast with MBT and. forms a non-scorchy accelerator. 2. The decrease in cure rate$(k_1)$ is attributable to the slow cure rate of 2-cyclohexyldithiobenzothiazole(CDB). 3. Cyclohexyl polysulfides(CPS) and cyclohexylthioamine are believed to be also involved in the cure retardation. 4. The new retarder can stop crosslinking by intercepting the crosslink precursors. 5. Formation of cyclohexyl polysulfides and their lack of curing property may be responsible for the low state of cure when the new retarde is used. These results are schematically summarized in Figure 7.