• Journal of Biosystems Engineering
• /
• 제18권3호
• /
• pp.252-261
• /
• 1993

Nuclear magnetic resonance(NMR) was used to study a feasibility test for the possibility to develop a moisture sensor applicable for agricultural products such as raw and powdered grain. Samples of wheat flour and brown rice were tested with a 200MHz hydrogen NMR. The samples were loaded into 5mm NMR glass tubes and $30^{\circ}$ pulses were supplied to get resonance signals. Hydrogen spectrum intensities of the samples were compared to moisture content measured by a drying oven method. High linear correlations were obtained between the hydrogen spectrum intensity and moisture content. Therefore, moisure contents of agricultural products could be measured nondestructively utilizing the NMR principle. A low-cost design concept of the moisture sensor with the NMR principle was proposed for a practical use.

• 한국철도학회논문집
• /
• 제11권1호
• /
• pp.1-6
• /
• 2008

본 연구에서는 현 고속 차량의 차체바닥 구조의 투과손실 특성 파악을 연구하고자 하였다. 이를 위하여 우선 허니콤 구조인 알루미늄 시편을 제작하여 투과손실 측정 실험을 수행하였다. 측정된 결과에서는 800Hz이상부터 질량 법칙을 따르는 투과손실의 특성을 파악할 수 있었다. 상용프로그램인 NASTRAN, AUTOSEA2를 사용하여 구조물에 대한 투과손실을 해석한 후 이를 실험치와 비교하여 신빙성 있는 결과를 얻을 수 있었다. 아울러 다른 단면 형상을 갖는 허니콤 구조물에 대한 투과손실 해석을 수행하여 특성을 예측해 보았다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권3호
• /
• pp.266-281
• /
• 2017

Hydroelastic interactions of a deformable floating body with random waves are investigated in time domain. Both hydroelastic motion and structural dynamics are solved by expansion of elastic modes and Fourier transform for the random waves. A direct and efficient structural analysis in time domain is developed. In particular, an efficient way of obtaining distributive loads for the hydrodynamic integral terms including convolution integral by using Fubini theory is explained. After confirming correctness of respective loading components, calculations of full distributions of loads in random waves are expedited by reformulating all the body loading terms into distributed forms. The method is validated by extensive convergence tests and comparisons against the counterparts of the frequency-domain analysis. Characteristics of motion/deformation responses and stress resultants are investigated through a parametric study with varying bending rigidity and types of random waves. Relative contributions of componential loads are identified. The consequence of elastic-mode resonance is underscored.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.551-556
• /
• 2009

Vehicle interior noise is the results of numerous sources of excitation. One source involving tire pavement interaction is the tire cavity resonance and the forcing it provides to the vehicle spindle. Using a simplified model for the tire acoustic cavity system only, we formulated finite element equation to predict the fundamental acoustic cavity resonant characteristics inside tire-wheel assembly of undeformed and deformed tire. Combining the finite element analysis with experimental verification, we explained the acoustic characteristics theoretically. Especially, we have shown that the difference between the first two resonant frequencies increases as the deformation of tire due to vertical load increases.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.552-558
• /
• 2001

When operating lathe gear box which is equipped with geared transmission, it sometimes generates loud noise and excessive vibrations. In order to identify their causes, in this study, torsional and lateral vibration characteristics including critical speeds of the gear transmission system are firstly analyzed using lumped parameter models. Natural frequencies and mode shapes of the gear box structure are also analyzed by using the modal test. Furthermore, measured vibration and noise signals during operations are analyzed and compared with theoretical analysis results. After all, it is concluded that the primary cause of the excessive noise and vibrations is the resonance between gear meshing frequency including its side bands, the frequencies of shaft bending and torsional vibrations, and the natural frequencies of the gear box structure. Consequently the noise and vibration levels are greatly reduced by avoiding resonance between the natural frequencies and gear meshing frequencies through the rearrangement of the gears on the transmission shaft without any gear ratio change.

• 한국철도학회논문집
• /
• 제8권3호
• /
• pp.228-234
• /
• 2005

Investigation on the dynamic behavior of railway bridges has not performed widely to date except high-speed railway bridges. In this study, 3-dimensional model is used for the finite element analysis of plate girder railway bridges. Train loads obtained through statistical approach of the measured true train loads are used. Numerical analysis is carried out about a 18m-span bridge. This result is compared with that of the experimental test of existing plate gilder railway bridge without ballast. The good agreement was obtained through the comparison. Judging from the analysis, resonant speed of diesel locomotive train is about 120km/h. However, the resonance for the other train is not found from the analysis.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.831-836
• /
• 2004

Vibration of electric-powered hand grinder comes from the parts of motor, gear, bearing, and fan. Excessive vibration can be harmful to workers. To reduce vibration of a hand grinder we analyzed the frequency components from the routing electric-powered grinder and did modal test to find the natural frequencies of the each part. It shows that the vibration is due to the resonance of the case. To remove the resonance, the case structure is modified and the bearing cap is replaced on a basis of the results from the rotor dynamic analysis using SAMCEF. As a result the vibration of the hand grinder is reduced greatly.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.107-112
• /
• 2012

All chemical processes are centered in the chemical reactor. Chemical reactions are often accompanied by mixing. Mixing can influence not just reaction rate but also product distribution if more than one product is possible. So, reactor agitator is more critical in industrial reactions. High vibration was occurred on reactor agitator which is critical equipment in HDPE plant. This paper describes analysis and diagnosis for agitator vibration throughout some tests. High vibration has been occurred by misalignment and resonance. Through the correction it could be stable.

• 동의생리병리학회지
• /
• 제30권1호
• /
• pp.73-79
• /
• 2016

It was aimed to report a case of both anterior cerebral artery territory infarction patient improved by korean medical treatment. The patient was diagnosed by brain magnetic resonance imaging(MRI) and magnetic resonance angiography(MRA). The symptoms were quadriplegia, urinary frequency, urinary incontinence and abulia. I applied herbal medicine, acupuncture, moxibustion, pharmacopuncture, cupping and physical exercise therapy. As a result of them, the symptoms of the patient were improved considerably. Status of the patient was evaluated by manaul muscle test(MMT), modified barthel index(MBI) and functional independence measure(FIM) and medical interview. MBI score was changed from 35 to 95 and FIM score was changed from 66 to 115. Therefore this report suggests that korean medical treatment could be effective to the anterior cerebral artery territory infarction.

• Tribology and Lubricants
• /
• 제26권2호
• /
• pp.97-104
• /
• 2010

A new magnetoelastic technique of oil viscosity measurement, where the oil viscosity is estimated by frequency shift of natural oscillations of magnetoelastic ribbon, is implemented in this study. Laboratory tests of the detector prototype are performed for measurement of viscosity of base synthetic and mineral oils. It was found that measurement accuracy was better when damping factor was estimated in comparison with accuracy of frequency of damped oscillations. Thus the oil viscosity was calibrated as a function of number of pulses of the damped oscillations of magnetoelastic ribbon. Result generally showed that developed detector is promising for in line oil viscosity measurement in wide viscosity range from 10 cSt up to 600 cSt, while the viscosity measurement was relatively instable when the viscosity of test oil was over 400 cSt.