• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.90-96
• /
• 2011

In this study, the characteristic of fractured portion and shape on solder joints were investigated according to the thermal shock test for Automotive Application Component using Sn-3.0Ag-0.5Cu solder, which has a outstanding property as Lead-free solder. The value of pull and shear strength was decreased in principle after 432 cycles thermal shock test. In addition, fracture mode was verified by using EDS and SEM to observe fractured shape on the solder joints before and after thermal shock. In before thermal shock test, the fracture mode revealed typically solder layer's fracture mode. In after thermal shock test, we identified multiple fracture mode of the ductile and brittle fracture. Even though same composition of solder was used to experimental for estimating. the fracture mode varied on the fracture portion's height and the directional angles of shear strength. In conclusion, we identified that mechanical strength was affected on the solder layer's fracture mode.

• Tunnel and Underground Space
• /
• v.20 no.5
• /
• pp.332-343
• /
• 2010

This study aims to evaluate the supporting effect of a spiral bolt that is superior to a rock bolt in terms of constructability, stability, environmental and economic aspects as a support system. This study thus analyzed the mechanical properties of a rock bolt which is widely used as a support and a spiral bolt. In addition, laboratory pull-out tests were conducted for the evaluation of properties of the supports such as displacement, pull-out load, confining pressure etc. Moreover, the differences between a rock bolt and a spiral bolt were drawn by comparing the two results of laboratory pull-out tests and in-situ pull-out tests. Then, the differences of the supporting effect of the two supports were analysed by comparing the results of the two pull-out tests with a numerical analysis using FLAC3D.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.2
• /
• pp.15-22
• /
• 2010

A series of field pull-out tests were carried out to investigate the behaviour of multi-pressurized soil nails. Ten soil nails were constructed in weathered soil and then, subjected to pull-out loads. The test results showed that the ultimate pull-out resistances of soil nails constructed with high pressure were about 42~142% larger than those obtained from conventional soil nails. The deduced interface shear strength at the ground-grout interface was 71 kPa for conventional soil nails, while higher shear strength of 95~166 kPa was obtained for pressurized nails. The diameter of grouted borehole increased by about 12~27% compared to ordinary soil nails under low pressure. Also, the predicted value by the cavity expansion theory is in good agreement with the measured expanded radius of grout under injection pressure by field pull-out tests.

• International Journal of Highway Engineering
• /
• v.6 no.1 s.19
• /
• pp.47-56
• /
• 2004

To determine the pure bond strength between substrate and its overlayed concrete material, a direct pull-off test method was introduced by using a bi-material cylinder with which a penny-shaped crack was mountained at its interface. First, to evaluate the stress magnification or concentration at the interface, the energy release rates of a penny-shaped interface crack in remote tension loading on a bi-material cylinder were determined in terms of different modulus ratios and undonded area ratios(crack ratios) using a commercial finite element program. Then the energy release rates were calibrated as non-dimensional values in consideration of structural dimensions and applied forces. And to evaluate whether this new pull-off test method gives sound test results, three different sizes of unbended area ratios were incorporated along their interface in bi-material cylinders(sulphur polymer concrete + old concrete). Test results showed that all specimens were broken off at their interfaces as intended. Also the FEM analyses and test results indicated that a bi-material specimen with unbended area ratio of 0.4$\sim$0.6 is suitable for best accurate testing.

• Proceedings of the Society of Korea Industrial and System Engineering Conference
• /
• 2002.05a
• /
• pp.63-68
• /
• 2002

This study performed to evaluated musculoskeletal disorders(MSDs) during sitting work. The musculskeletal system is affected by various work factors such as strength, weight, posture, repetition, duration and exertion. Ergonomic study on sitting work is necessary to evaluate these factors affecting human body. But the strength and work load data by the work factors are insufficient in Korea. Therefore, this study evaluated the work load using the elcctromyogram(EMG) and measured the arm strength by arm posture and push pull work during sitting work. to evaluated muscle load, the vertical height and horizontal angle of arm were adjusted around acromion. And EMG data were recorded on pc during the test.

• Journal of the Korean Society of Safety
• /
• v.17 no.2
• /
• pp.85-91
• /
• 2002

A research on the performance of retrofit anchors was conducted using adhesives for rehabilitation. From the pull-out tests of the chemical anchors, the effect of the hole diameter, spacer, temperature, moisture, embedment depth, and aging time were investigated. The spacer did not directly increased the pull-out load hilt increased post-yielding resistance therefore the ductility of the retrofit anchors. When the hole was cleaned and dried after the immersion, the pull-out load was greatly increased compared to the wet hole. A design equation was unposed depending on the embedment depth of the anchor bolt.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.405-411
• /
• 2008

The pressurized grouting soil nailing method using rubber membrane packer system was developed for recycling materials to minimize environmental pollution and reducing construction costs. For this purpose, field pull-out tests were performed to evaluate the characteristics of soil nailing by measuring tensile stresses and axial displacements.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.127-134
• /
• 2000

Soil nailing is in-situ ground improvement technique of reinforcing soils using passive inclusions for the purpose of slope stability. Also soil nailing, in general, was used and studied as a reinforcement technique at cut slope, but this paper presents the results of study for soil nailing application as a reinforcement technique at the banking over slided slope. In-situ pull-out tests of nails, instrumented with strain gauges, were performed to investigate the maximum pull-out load and to calculate the unit side resistance in each different layer. And the apparent average unit side resistance of this study was compared with that of other sites installed at cut slope.

• Journal of Korean Association for Spatial Structures
• /
• v.15 no.4
• /
• pp.65-72
• /
• 2015

To overcome the weakness of spread foundation in large space structure, the research of precast pile for replace spread foundation have been conducted. The new type of joint between PHC pile and steel column is named HAT Joint(Hollow hAlf-sphere cast-sTeel Joint). It connected PHC Pile by bolt that verification of bolt connection should be accomplished. In this paper, pull-out test and flexural performance for HAT Joint to verifying the bolt connection is explained. As a result, the pull-out and flexural capacities of bolt were checked to use in real structure. Furthermore, the equation of pull-out strength was proposed.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.04a
• /
• pp.268-271
• /
• 2003

연구지역에 설치된 3개 관정에서 추적자시험 방법 중 단공 주입-회수시험을 실시하였다. Push-pull 추적자시험 자료 분석 결과 종분산지수는 0.086~0.657m의 값을 가지며(Pickens and Grisak, 1981), 지하수 유동속도는 9.07$\times$$10^{-4}$6.14$\times$$10^{-3}$m/min의 값을 보인다(Hall and other, 1991). 또한 계산된 종분산지수와 지하수 유속을 이용하여 종분산계수(3.77$\times$$10^{-4}$ ~ 9.53$\times$$10^{-4}$ $m^2$/min)를 산정하였다. 추적자의 거동특성이 크고 작음을 비교할 수 있게 하는 특성변수(Characteristic property)는 분산지수이므로, 분산지수의 크고 작음에 따라서 추적자의 거동특성이 달라짐에 주의해야 한다..