• Advances in concrete construction
• /
• 제9권4호
• /
• pp.367-374
• /
• 2020

Concrete surfaces, industrial floors, sidewalks, roads and parking lots are typically subjected to abrasions. Many studies indicated that the abrasion resistance is directly related to the ultimate strength of the cured concrete. Chemical reactions, freeze-thaw cycles, and damages under abrasion are among many factors negatively affecting the concrete strength and durability. One of the major solutions to address the abrasive resistance of the concrete is to use fibers. Fibers are used in the concrete mix to improve the mechanical properties, strength and limit the crack propagations. In this study, implementation of the steel fibers in concrete to enhance the abrasive resistance of the concrete is investigated in details. The abrasive resistance of the concrete with and without steel fibers is studied with the sandblasting technique. For this purpose, different concrete samples are made with various hooked steel fiber ratios and investigated with the sandblasting method for two different strike angles. In total, 144 ASTM verified cube samples are investigated and it is shown that those samples with the highest steel fiber ratios have the highest abrasive resistance. In addition, the experiments determine that there is a meaningful correlation between the steel fiber percentage in the mix, strike angle and curing time which could be considered for improving structural behavior of the fiber-reinforced concrete.

• 한국통신학회논문지
• /
• 제31권2C호
• /
• pp.109-116
• /
• 2006

초광대역(UWB) 통신시스템의 응용 시나리오는 많은 경우 비가시적(non-LoS) 환경에서의 응용을 가정하고 있다. UWB 신호가 매질을 투과하여 방사될 경우 신호의 왜곡현상이 발생하며, 이는 수신부 상관기의 기준신호와 수신된 신호와의 상관계수를 감소시켜 성능을 저하시키는 요인이 된다. 본 논문에서는 가설검증 방식을 이용한 UWB Rake 수신기의 기준신호 선택 기법을 소개한다. 가설을 세우기 위한 파형의 선택을 위해 벡터 양자화 기법인 Linde-Buzo-Gray(LBG) 알고리듬을 사용하였다. 개시된 알고리듬을 성능을 non-LoS 환경에서 측정된 데이터를 이용해 평가하였다.

• 한국해안해양공학회지
• /
• 제19권2호
• /
• pp.170-178
• /
• 2007

대부분의 포물형 수치모형은 경계 외측의 수심이 해안방향으로 변하지 않는 Snell 법칙을 적용할 수 있는 조건으로 국한한다. 여기에는 기존의 Kirby 방법이 있으며 본 논문에서는 이를 수정한 방법 그리고 Dirichlet 경계조건에 대해 자세히 기술하고 이에 대한 수치실험 결과를 제시하였다. 일정 수심 위에 존재하는 원형 천퇴에 대한 수치실험 결과 계산영역 좌우에 가상 수치 조정구역을 두고 본 Dirichlet 경계조건을 적용한 경우가 파고비의 분포가 가장 작게 왜곡되는 것으로 나타났다.

• 한국가시화정보학회지
• /
• 제8권1호
• /
• pp.19-24
• /
• 2010

Five different size of orifice were applied in a constant volume combustion chamber for evaluating the effects of torch-ignition on combustion. The initial flame development and flame propagation were analyzed by the mass burned fraction and combustion enhancement rate. The combustion pressures were measured to calculate the mass burned fractions and the combustion enhancement rates. In addition, the flame propagations were visualized by the shadowgraph method for the qualitative comparison. The result showed that the combustion pressure and mass burned fraction were increased when using the torch-ignition device. The combustion enhancement rates of torch-ignition cases were improved in comparison with conventional spark ignition. Finally, the visualization results showed that the torch-ignition induced faster burn than conventional spark ignition due to the earlier transition to turbulent flame and larger flame surface, during the initial stage.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제7권9호
• /
• pp.2154-2172
• /
• 2013

A centralized cognitive radio (CR) network is proposed and its system capacity is studied. The CR network is designed with power control and multi-user scheduling schemes to support best-effort traffics under peak interference power constraints. We provide an analytical framework to quantify its system capacity, taking into account various key factors such as interference constraints, density of primary users, cell radius, the number of CR users, and propagations effects. Furthermore, closed-form formulas are derived for its capacities when only path loss is considered in the channel model. Semi-analytical expressions for the capacities are also given when more realistic channel models that include path loss, shadowing, and small-scale fading are used. The accuracy of the proposed analytical framework is validated by Monte Carlo simulations. Illustrated with a practical example, the provided analytical framework is shown to be useful for the strategic planning of centralized CR networks.

• Structural Engineering and Mechanics
• /
• 제53권6호
• /
• pp.1083-1104
• /
• 2015

This paper provides the results of an experimental investigation into the flexural behavior of continuous two-span unbonded post-tensioned high strength concrete (HSC) beams, strengthened by end-anchored CFRP laminates of different configurations in the hogging region. Implementing two different configurations of end-anchorage systems consisting of steel plates and bolts and carefully monitoring the development of strains throughout the load history using sufficiently large number of strain gauges, the response of beams including the observed crack propagations, beam deflection, modes of failure, capacity enhancement at service and ultimate and the amount of moment redistribution are measured, presented and discussed. The study is appropriate in the sense that it covers the more commonly occurring two span beams instead of the simply supported beams investigated by others. The experiments reconfirmed the finding of others that proper installation of composite strengthening system is most important in the quality of the bond which is essential for the internal transfer of forces. It was also found that for the tested two span continuous beams, the capacity enhancement is more pronounced at the serviceability level than the ultimate. This is an important finding as the design of these beams is mostly governed by the serviceability limit state signifying the appropriateness of the suggested strengthening method. The paper provides quantitative data on the amount of this capacity enhancement.

• Geomechanics and Engineering
• /
• 제10권3호
• /
• pp.285-296
• /
• 2016

The investigation of stress wave propagation in a medium with initial stress has very important application in the field of engineering. However, the previous research less consider the influence of initial stress gradient on wave propagation. In the present paper, the governing equation of wave propagation in elastic continuum material with inhomogeneous initial stress is derived, which indicated that the inhomogeneous initial stress changed the governing equation of wave propagation. Additionally, the definite problem of wave propagation in material with initial stress gradient is verified by using mathematical physics method. Based on the definite problem, the elastic displacement-time relationship of wave propagation is explored, which indicated that the inhomogeneous initial stress changed waveform and relationship of displacement-time histories. Furthermore, the spall process of blasting wave propagation from underground to earth surface is simulated by using LS-DYNA.

• 한국안전학회지
• /
• 제26권6호
• /
• pp.26-30
• /
• 2011

Experimental investigations were performed to examine the effects of different electrostatic discharge ignition energies on LPG/air mixture explosions in an explosion chamber. The chamber consisted of 500 mm in length, with a $100{\times}100mm^2$ cross section. Three different ignition energies were used: 0.30 mJ, 46 mJ and 98 mJ. Flame propagations were recorded by a high speed video camera. The results of flame speed and pressure obtained from the different ignition energies were discussed. It was found that as the energy increased, different flame initiations occurred. This caused the time interval in both the flame and pressure developments. It was also found that the flame speed and the pressure were less sensitive to both 0.30 mJ and 46 mJ, except for the ignition energy of 98 mJ.

• 한국전기전자재료학회논문지
• /
• 제29권3호
• /
• pp.152-158
• /
• 2016

The bonding characteristics of MLCCs (multi layer ceramic capacitor, C1608) lead-free solder (SAC305) joints were evaluated through thermal shock test ($-40^{\circ}C{\sim}125^{\circ}C$, total 1,800 cycle). After the test, IMCs( intermetallic compounds) growth and cracks were verified, also shear strengths were measured for degradation of solder joints. In addition, The thermal stress distributions at solder joints were analyzed to compare the solder joints changes before and after according to thermal shock test by FEA (finite elements analysis). We considered the effects of IMCs growth at solder joints. As results, the bonding characteristics degradation was occurred according to initial crack, crack propagations and thermal stress concentration at solder-IMCs interface, when the IMCs grown to solder inside.

• Steel and Composite Structures
• /
• 제33권5호
• /
• pp.699-716
• /
• 2019

In this paper, wave propagations in sigmoid functionally graded (S-FG) plates are studied using new Higher Shear Deformation Theory (HSDT) based on two-dimensional (2D) elasticity theory. The current higher order theory has only four unknowns, which mean that few numbers of unknowns, compared with first shear deformations and others higher shear deformations theories and without needing shear corrector. The material properties of sigmoid functionally graded are assumed to vary through thickness according sigmoid model. The S-FG plates are supposed to be imperfect, which means that they have a porous distribution (even and uneven) through the thickness of these plates. The governing equations of S-FG plates are derived employed Hamilton's principle. Using technique of Navier, differential equations of S-FG in terms displacements are solved. Extensive results are presented to check the efficient of present methods to predict wave dispersion and velocity wave in S-FG plates.