• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.318-330
• /
• 2013

This paper presents a high-linearity low-noise small-size programmable gain amplifier (PGA) based on a new low-noise low-distortion differential amplifier and a proposed reconfiguration technique. The proposed differential amplifier combines an inverter-based differential pair with an adaptive biasing circuit to reduce noise and distortion. The reconfiguration technique saves the chip size by half by utilizing the same differential pair for the input transconductance and load-stage, interchangeably. Fabricated in $0.18-{\mu}m$ CMOS, the proposed PGA shows a dB-linear control range of 21dB in 16 steps from -11 dB to 10 dB with a gain error of less than ${\pm}0.33$ dB, an IIP3 of 7.4~14.5 dBm, a P1dB of -7~1.2 dBm, a noise figure of 13dB, and a 3-dB bandwidth of 270MHz at the maximum gain, respectively. The PGA occupies a chip area of $0.04mm^2$ and consumes only 1.3 mA from the 1.8 V supply.

• Journal of Korea Multimedia Society
• /
• v.5 no.6
• /
• pp.753-758
• /
• 2002

In this paper, low voltage 3V CMOS programmable gain amplifier(PGA) for using in the transmitter and receiver of ADSL analog front-end is designed. The designed receive PGA is connected with 1.1MHz continuous lowpass fillet and controls the gain from 0dB to 30dB. And also the transmitter PGA is connected with 138KHz lowpass filter and controls the gain from -15dB to 0dB. The gain of All PGAs can be programmed by digital logic circuits and main controller. The designed PGAs are verified using HSPICE simulation with $0.35\mu{m}$ CMOS parameter.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.324-331
• /
• 2013

In this paper, we implemented memristor emulator circuit on Printed Circuit Board (PCB) and observed the inherent pinched hysteresis characteristic of memristors by measuring the emulator circuit on PCB. The memristor emulator circuit implemented on PCB is composed of simple discrete devices not using any complicated circuit blocks thus we can integrate the memristor emulator circuits in very small layout area on Silicon substrate. The programmable gain amplifier is designed using the proposed memristor emulator circuit and verified that the amplifier's voltage gain can be controlled by programming memristance of the emulator circuit by circuit simulation. Threshold switching is also realized in the proposed emulator circuit thus memristance can remain unchanged when the input voltage applied to the emulator circuit is lower than VREF. The memristor emulator circuit and the programmable gain amplifier using the proposed circuit can be useful in teaching the device operation, functions, characteristics, and applications of memristors to students when thet cannot access to device and fabrication technologies of real memristors.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.349-351
• /
• 2013

This research paper presents a low-power programmable gain amplifier (PGA) to facilitate signal processing of the detection of defects in steel plates. This circuit is able to adjust a gain in the range of 6 to 60dB in 7 steps using different signal types for various defects from hall sensors. The gain of PGA is designed by operating on-resistors of switches and passive components. The proposed PGA ($0.18{\mu}m$ CMOS process with 1.8 supply voltage) showed excellent gain error of less than -0.2dB, and low power consumption of 0.47mW.

• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.5
• /
• pp.15-18
• /
• 2013

This paper presents an analog front-end for electroencephalogram(EEG) signal processing. Since EEG signals are typically weak and located at very low frequencies, it is imperative to implement an amplifier with high gain, high common-mode rejection ratio(CMRR) and good noise immunity at very low frequencies. The analog front-end of this paper consists of a programmable-gain instrumentation amplifier and a band-pass filter. A frequency chopping technique is employed to remove the low-frequency noise. The circuits were fabricated in 0.18um CMOS technology and measurements showed that the analog front-end has the maximum gain of 60dB and >100dB CMRR over the programmable gain range.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.1004-1007
• /
• 2005

This paper presents a programmable RF BIST (Built-in Self-Test) circuit for low noise amplifiers. We have developed a new on-chip RF BIST circuit that measures RF parameters of low noise amplifier (LNA) using only DC measurements. The BIST circuit contains test amplifier with programmable capacitor banks and RF peak detectors. The test circuit utilizes output DC voltage measurements and these measured values are translated into the LNA specifications such as input impedance and gain using the mathematical equations. Our on-chip BIST can be self programmed for 1.8GHz, 2.4GHz and 5.25GHz LNA for GSM, Bluetooth and IEEE802.11g standards.

• ETRI Journal
• /
• v.31 no.2
• /
• pp.234-236
• /
• 2009

We present a novel operational amplifier preset technique for a switched-capacitor circuit to reduce the acquisition time by improving the slewing. The acquisition time of a variable gain amplifier (VGA) using the proposed technique is reduced by 30% compared with a conventional one; therefore, the power consumption of the VGA is decreased. For additional power reduction, a programmable capacitor array scheme is used in the VGA. In the 0.13 ${\mu}m$ CMOS process, the VGA, which consists of three-stages, occupies 0.33 $mm^2$ and dissipates 19.2 mW at 60 MHz with a supply voltage of 1.2 V. The gain range is 36.03 dB, which is controlled by a 10-bit control word with a gain error of ${\pm}0.68$ LSB.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.299-301
• /
• 2014

본 논문에서는 직류 오프셋 (DC-offset) 제거 기능을 가진 저 전력 자동 이득 조절 증폭기 (PGA, Programmable Gain Amplifier)를 제안한다. 이러한 회로는 직류 오프셋 문제점을 해결하기 위해 기존의 gm-boosting 증폭기를 변형한 디지털 이득 제어 방식으로 설계되어 있기 때문에 우수한 선형성을 가진다. 또한 특수 목적에 맞도록 그 이득을 6dB에서 60dB까지 7단계로 조절 가능하며, 밀러효과를 이용한 AC-coupling 방식으로 큰 값의 유동적인 커패시터와 저항을 구현하여 직류 오프셋을 제거한다. 제안한 PGA는 기존 회로에 비해 0.2dB 보다 작은 이득오차와 0.47mW의 낮은 소비전력 특성을 보였다.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.4
• /
• pp.28-39
• /
• 2007

This paper presents a programmable RF DFT (Radio Frequency Design-for-Testability) circuit for low noise amplifiers. We have developed a new on-chip RF DFT circuit that measures RF parameters of low noise amplifier (LNA) using only DC measurements [1, 2]. This circuit is extremely useful for today's RFIC devices in a complete RF transceiver environment. The DFT circuit contains test amplifier with programmable capacitor banks and RF peak detectors. The test circuit utilizes output DC voltage measurements and these measured values are translated into the LNA specifications such as input impedance and gain using the mathematical equations. Our on-chip DFT circuit can be self programmed for 1.8GHz, 2.4GHz and 5.25GHz low noise amplifiers for GSM, Bluetooth and IEEE802.11g standards. The circuit is simple and inexpensive.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.354-356
• /
• 2013

본 논문에서는 CMOS 스위치를 이용한 디지털 이득 제어 구조를 가진 이득 조절 증폭기 (PGA, Programmable Gain Amplifier)를 제안한다. 기존의 아날로그 이득 제어 방식에서는 가변적인 트랜스 컨덕턴스를 활용하는 과정에서 바이어스 전류나 전압에 의해 이득이 변하게 되어 순간적으로 구성회로의 바이어스 포인트가 변하기 때문에 왜곡이 발생하게 되는 문제점이 있다. 본 논문에서는 이러한 문제점을 해결하기 위해 기존의 gm-boosting 증폭기를 변형한 디지털 이득 제어 방식으로 설계되어 있기 때문에 우수한 선형성을 가지며 특수 목적에 맞도록 그 이득을 6dB에서 60dB까지 7가지 단계로 조절 가능하다. 제안한 PGA는 기존 회로에 비해 0.2dB 보다 작은 이득오차와 0.47mW의 낮은 소비전력 특성을 보였다.