• 한국축산식품학회지
• /
• 제42권6호
• /
• pp.942-952
• /
• 2022

To establish a pre-plating method of chicken satellite cells with high purity, pre-plating was performed under culture conditions of 37℃ and 41℃, and the pre-plating time was set from a total of 3 hours to 6 hours in consideration of the cell attachment time. The purity of the cells was confirmed by staining paired box protein 7 (Pax7) after proliferation, and Pax7 expression was the highest in culture flasks shaken for 2 hours after incubation at 41℃ for 2 hours to prevent the attachment of satellite cells (p<0.05). Also, when pre-plating and proliferation were performed at 37℃ and 41℃, the Pax7 expression rate was higher at 41℃. The differentiation capabilities of the three groups (T3, T6, and T7) with high Pax7 expression were compared and the fusion index (%) and myotube formation area (%) determined by myosin heavy chain (MHC) staining was calculated. The T6 and T7 groups, which were cultured at 41℃, showed significantly higher values than the T3 group (p<0.05). There was no significant difference in the expression of Pax7 and MHC between the T6 and T7 groups (p>0.05). These results suggest that pre-plating at 41℃ for a total of 4 hours was the most efficient in terms of cost and time for purifying chicken satellite cells for cultured meat.

• 한국표면공학회지
• /
• 제49권3호
• /
• pp.265-273
• /
• 2016

The effects of surface modification by nitric acid on the pre-treatment of electroless copper plating were investigated. Copper was electroless-plated on the nitric acid treated graphite activated by a two-step pre-treatment process (sensitization + activation). The chemical state and relative quantities of the various surface species were determined by X-ray photoelectron spectroscopy (XPS) after nitric acid modification or pre-treatment. The acid treatment increased the surface roughness of the graphite due to deep and fine pores and introduced the oxygen-containing functional groups (-COOH and O-C=O) on the surface of graphite. In the pre-treatment step, the high roughness and many functional groups on the nitric acid treated graphite promoted the adsorption of Sn and Pd ions, leading to the uniform adsorption of catalyst ($Pd^0$) for Cu deposition. In the early stage of electroless plating, a lot of tiny copper particles were formed on the whole surface of acid treated graphite and then homogeneous copper film with low variation in thickness was formed after 30 min.

• Corrosion Science and Technology
• /
• 제18권4호
• /
• pp.148-153
• /
• 2019

Pure nickel with a thickness of 1 mm was plated on type 304 stainless steels and low alloy steels (JIS G3131 SPHC) by electrolytic plating method in a circulating plating bath. Plating performance, mechanical properties, and surface characteristics were evaluated in terms of pretreatment process, anode material, pH, current density, and flow rate of the plating solution. Addition of hydrochloric acid during pre-treatment process improved the adhesion performance of plating. To improve plating efficiency, it is desirable to use S-nickel rather than electrolytic nickel. The use of S-nickel was also confirmed to be desirable for maintaining the pH and concentration of the plated solution. The defect of the plating using S-nickel anode produced pit on the surface. However, it is believed that proper control can be obtained by increasing the flow rate. Internal stress and hardness values of electrolytic nickel plating according to current density need to be carried out with further studies.

• 한국재료학회지
• /
• 제32권9호
• /
• pp.361-368
• /
• 2022

The overall process, from the pre-treatment of aluminum substrates to the eco-friendly neutral electroless Ni-P plating process, was observed, compared, and analysed. To remove the surface oxide layer on the aluminum substrate and aid Ni-P plating, a zincation process was carried out. After the second zincation treatment, it was confirmed that a mostly uniform Zn layer was formed and the surface oxide of aluminum was also removed. The Ni-P electroless plating films were formed on the secondary zincated aluminum substrate using electroless plating solutions of pH 4.5 and neutral pH 7.0, respectively, while changing the plating bath temperature. When a neutral pH7.0 electroless solution was used, the Ni-P plating layer was uniformly formed even at the plating bath temperature of 50 ℃, and the plating speed was remarkably increased as the bath temperature was increased. On the other hand, when a pH 4.5 Ni-P electroless solution was used, a Ni-P plating film was not formed at a plating bath temperature of 50 ℃, and the plating speed was very slow compared to pH 7.0, although plating speed increased with increasing bath temperature. In the P contents, the P concentration of the neutral pH 7.0 Ni-P electroless plating layer was reduced by ~ 42.3 % compared to pH 4.5. Structurally, all of the Ni-P electroless plating layers formed in the pH 4.5 solution and the neutral (pH 7.0) solution had an amorphous crystal structure, as a Ni-P compound, regardless of the plating bath temperature.

• 대한산업공학회지
• /
• 제34권3호
• /
• pp.337-343
• /
• 2008

The problem of determining the optimum metal plating thicknesses on the plane and curved surfaces of an electronic part is considered. A lower specification limit for the plating thickness is usually pre-specified. In most applications, the plating thickness on the curved surface is proportional to that on the plane surface. The proportion can be adjusted by adding chemical catalysts to the plating fluid. From the economic point of view, nonconforming items with a thickness smaller than the lower specification limit incur rejection costs, such as rework and scrap costs, while a thicker plating may incur an excessive material costs. In this article, an economic model is proposed for simultaneously determining the target plating thickness and the ratio of the plating thickness on the plane surface to that on the curved surface. An illustrative example demonstrates the applicability of the proposed model.

• 품질경영학회지
• /
• 제45권3호
• /
• pp.327-333
• /
• 2017

Purpose: The purpose of this study is to research to protect to loss of chrome-plating of small arms barrel on high temperature in order to extend its life expectency. Methods: The reason why chrome-plating dropped out is main material is weak from heat. Therfore, to make barrel of small arms have higher heat-resistant property, nitriding for barrel before chrome-plating is needed and test of that barrel was handled to improve it. Results: Nitriding before chrome-plating is useful to protect to chrome-plating loss on high temperature. Conclusion: To protect loss of chome-plating of small arms barrel during on firing, pre-nitriding on barrel is effective finally it leads to extend to barrel's life expectency.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.219-223
• /
• 1999

A new additive for semi-brightness finish in nickel electroplating, having a quarternary ammonium salt structure, has been developed in this study. The effectiveness of the new additive was tested in laboratory-scale eletroplating tests as well as in a full-scale factory plating line. An examination of the plated surface showed that the new additive is as good as the one produced by the most commonly used additive in the nickel plating industry. The plated surface was examined by SEM, EPMA, and Reflectance Spectroscopy, and was found to be compatible to the one obtained with commercial additives. The new additive has a shelf life comparable with those of other commercially available additives. The additive developed in this study has an excellent potential to be used commercially.

• 마이크로전자및패키징학회지
• /
• 제11권2호
• /
• pp.11-16
• /
• 2004

전자칩의 고집적화에 의해 전자기기들은 점점 소형화 되어가고 있으며, 이들 기기들에서 발생되는 열은 기기의 성능 저하뿐 아니라 수명을 단축시킨다. 본 연구에서는 효율적인 방열 위한 마이크로 히트싱크 제조를 위하여 멤브레인에 금속(금, 니켈, 구리)은 도금하는 무전해 도금 방법을 이용하였다. 무전해 도금은 폴리카보네이트 멤브레인을 sensitization과 activation 등의 전처리 후, 도금하고자 하는 금속염 수용액에 침적시켜 실행하였다. 무전해 도금에 의하여 제조된 각각의 마이크로피브릴의 열전달 특성과 방열량은 표면적이 가장 큰 니켈 마이크로피브릴에서 가장 우수하게 나타났다.

• 폴리머
• /
• 제34권1호
• /
• pp.25-31
• /
• 2010

무전해 니켈 도금법을 사용하여 단분산 폴리스티렌 입자 표면에 니켈이 도금된 고분자 코어/금속 쉘의 복합 입자를 제조하였다. 단분산 입자는 분산중합으로 제조하였는데 사용한 분산매질의 종류에 따라 다양한 크기의 단분산 폴리스티렌 입자를 제조할 수 있었다. 그 중 직경 $3.4\;{\mu}m$ 크기의 단분산 폴리스티렌 입자를 선택하여 무전해 니켈 도금을 시도하였다. 니켈 도금에 영향을 미치는 도금 조건을 파악하기 위하여 활성화제인 $PdCl_2$의 농도, 착화제인 glycine의 농도와 니켈 도금액의 투여 시간에 따른 니켈 도금된 폴리스티렌 복합 입자의 모폴로지를 관찰하였다. 본 연구조건하에서는 $PdCl_2$의 농도 0.4 g/L, glycine 농도 1 M 이상인 경우 폴리스티렌 입자 위에 균일한 두께의 니켈층을 형성하였고 석출되는 니켈도 적었다. 도금 시간 2 시간 중에서 동일양의 도금액을 투여 속도를 달리하며 도금한 경우 모폴로지 상의 뚜렷한 차이는 없었으나 0.15 mL/min 속도로 1시간 동안 투여한 경우가 상대적으로 균일한 도금 특성을 보여 주었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2015년도 추계학술대회 논문집
• /
• pp.193-193
• /
• 2015

도금공정에 있어서 전처리는 제품품질을 확보하는데 중요한 단계이다. 전처리 공정의 주요인자중 처리액의 온도, 처리시간, 교반력, 오염도를 개선함으로써 제품의 산화막 및 오염물질을 효과적으로 제거할 수 있었다.