• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.6
• /
• pp.709-719
• /
• 2023

In general, most of the electrical equipment responsible for control within power plants is housed in self-standing cabinets. These cabinets are typically fixed to a slab using post-installed anchors. Although the fixation method of using post-installed anchors provides stability, there is a risk of conductor failure due to external forces, including moments. However, the performance assessment of current anchors is only evaluated through uniaxial material tests. Therefore, the primary purpose of this study is to compare the static performance of post-installed anchors, considering on-site installation conditions, with their performance in material tests and to analyze the behavioral characteristics of the anchors. While conducting experiments using actual cabinets would be ideal, practical and spatial constraints make this approach difficult. As an alternative, experiments were conducted using a test specimen consisting of a steel column and a support. As a result, the pull-out performance of anchors reflecting on-site installation conditions was measured to be about 10% higher than that observed in material tests. The trends in load reduction and the point of maximum performance for the anchors also differed. To verify the reliability of the experimental study, a 3D FEM analysis was performed, which will provide predictive information on the loads transferred to the post-installed anchors for structural performance evaluations of electrical cabinets using shaking table test in the future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.377-383
• /
• 2012

In this paper, a new design of a planar rectenna system and its application to a wake-up receiver operating for incoming signal with a specified frequency are proposed for low-power sensor system applications. The planar and integrable rectenna system is designed with DGSs(Defected Ground Structures) at 2.4 GHz. The DGSs reject harmonic components of 4.8 and 7.2 GHz and eliminate 2.4 GHz fundamental frequency for DC-path filtering. The rectenna system has been evaluated for the conversion output voltages, and applied to the switching of a power supply at the low-power sensor receivers. The proposed system has been evaluated for the wake-up performance by testing a lownoise amplifier operation. From the experimental results, the proposed receiver system presents excellent operation performances.

• Journal of Preventive Medicine and Public Health
• /
• v.46 no.2
• /
• pp.74-81
• /
• 2013

Objectives: The objective of this study was to evaluate the performance of risk-adjusted mortality models for colorectal cancer surgery. Methods: We investigated patients (n=652) who had undergone colorectal cancer surgery (colectomy, colectomy of the rectum and sigmoid colon, total colectomy, total proctectomy) at five teaching hospitals during 2008. Mortality was defined as 30-day or in-hospital surgical mortality. Risk-adjusted mortality models were constructed using claims data (basic model) with the addition of TNM staging (TNM model), physiological data (physiological model), surgical data (surgical model), or all clinical data (composite model). Multiple logistic regression analysis was performed to develop the risk-adjustment models. To compare the performance of the models, both c-statistics using Hanley-McNeil pair-wise testing and the ratio of the observed to the expected mortality within quartiles of mortality risk were evaluated to assess the abilities of discrimination and calibration. Results: The physiological model (c=0.92), surgical model (c=0.92), and composite model (c=0.93) displayed a similar improvement in discrimination, whereas the TNM model (c=0.87) displayed little improvement over the basic model (c=0.86). The discriminatory power of the models did not differ by the Hanley-McNeil test (p>0.05). Within each quartile of mortality, the composite and surgical models displayed an expected mortality ratio close to 1. Conclusions: The addition of clinical data to claims data efficiently enhances the performance of the risk-adjusted postoperative mortality models in colorectal cancer surgery. We recommended that the performance of models should be evaluated through both discrimination and calibration.

• Journal of Hydrogen and New Energy
• /
• v.25 no.5
• /
• pp.533-540
• /
• 2014

The remanufacturing industry for automotive parts is a major issue which affects the environment protection and CO2 reduction throughout the world. Beside this, remanufacturing technologies of worn-out diesel engines have been developing to make as close to new as possible. In this study, the characteristics of the engine-power output and exhaust emissions of remanufactured diesel engine by hydrogen enrichment are evaluated by measuring the engine and vehicle test. Moreover, with worn-out diesel engine and first generation common-rail engine, we compared by testing their characteristics, resulting in the restoration of engine-power output more than 93%, as well as marvelously reduces the THC and NOx emission. At a guess, high pressure injection of diesel increases fuel atomization characteristics with excellence combustion efficiency, resulting in reduction of THC emission. Also, rapid cooling of EGR decreases combustion temperature, resulting in reduction of NOx emission. Consequently, these remanufacturing for diesel engine enables worn-out diesel engine to have restoration to the original state. Simultaneously achieved 2 goals called that CO2 emission reduction and protection of environment by remanufacturing engine.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.415-423
• /
• 2018

We herein investigate the E1 pulse for evaluating the conducted performance of transmission lines connected to the electromagnetic pulse protection facilities against a conducted high-altitude electromagnetic pulse threat exposed to an external electromagnetic environment. The existing E1 pulse generator uses the Marx generator high-voltage step-up method; however, in this research, we used the Tesla transformer method to easily change the broadband output voltage(30 to 350 kV). We also analyzed the controller, power supply, high-voltage booster, and pulse-shaping device. The E1 pulse performance using the Tesla transformer was predicted through simulations and validated by measurements.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.11A
• /
• pp.1117-1123
• /
• 2008

Applications for mobile multimedia are testing the performance limits of present day CPUs with variety. However, hardwired solutions are inflexible and expensive to develop. CPUs with flexibility have limitation of performance. So, the requirement for both ASIC-like performance and CPU-like flexibility has led to reconfigurable processor. Mobile systems require low power and high performance concurrently. In this paper, we propose reconfigurable processor for mobile multimedia with high energy efficiency. Reconfigurable processor with 121MOPS/mW is developed by 130nm CMOS technology. And the processor was simulated for energy efficiency with 539MOPS/mW by 90nm CMOS technology and effective use of instructions. And we tested its applications for multimedia field. We tested the case of inverse MDCT for MP3 and DF for MPEG4 and ME for H.264.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.1-8
• /
• 2017

The Down-the-Hole hammer is one of the pneumatic drill equipment used for grinding, drilling, and mining. One the advantages of which is that a reduction work efficiency at deep site are relatively small compared to other drilling methods. Due to the large vibration in the underground area, it is difficult to measure the performance of the hammer, and hammer testing requires substantial production cost and operating expenses so research on the development of the hammer is insufficient. Therefore, this study has developed a dynamic simulation model that apprehends the operating principles of an 8-inch DTH hammer and calculates performance data such as performance impact force, piston speed, and BPM. By using the simulation model, design factors related to strike force and BPM were selected, and the influence of each design factors on performance was analyzed through ANOVA analysis. As a result, be the most important for BPM and the strike force are position of upper port that push the piston in the direction of the bit and in BPM, the size of the empty space between the bits and the piston is the second most important design factor.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.5 no.6
• /
• pp.317-325
• /
• 2015

The aim of this research was to investigate the relationship among team learning behavior, individual creativity, team shared mental model(TSMM), mutual performance monitoring on team creativity and then providing the fundamental data on the education. Also it intended to acknowledge relative predictive power on team creativity of independent variables. The total of 257 college students participated the team learning for 6 weeks in a semester. Pearson's product moment correlation and regression analysis were used for data analysis and testing of significance of verification, The main research results are summarized as follows; team learning behavior, TSMM, mutual performance monitoring had no significant effects on three subfactors of team creativity such as novelty, resolution, elaboration & synthesis. Therefore followed researches are needed about inter and intra processing of team creativity.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.9
• /
• pp.739-745
• /
• 2014

Although medication is given to heart disease patients, conventional medication alone is not sufficient to treat heart disease. However, it has been reported that left ventricular assist device (LVAD) transplantation is an effective bridge to heart transplantation by assisting cardiac function. This study used long-term animal testing and emergency situations with a bovine model (Holstein) and canine model (Labrador-retriever) to evaluate the biocompatibility of LibraHeart-I (LH-1), which is a bent-tube type of LVAD that was developed in a previous study. In the long-term animal testing with the bovine model, the subjects survived for 49 days with no irregularities observed in their complete blood cell counts or the vital sign tests that were carried out during the test period. In short-term animal testing with the canine model, it was observed that blood did not remain inside the LH-I even without power support from an external drive source. In this study, the biocompatibility of the LH-I that was developed in a previous study was verified by the ejection performance during long-term animal testing and emergency situations.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.6
• /
• pp.638-646
• /
• 2023

Recently, active research has been conducted to enhance the power characteristics and thermal stability of lithium-ion batteries (LiBs) by modifying separators using a ceramic coating method. However, since the thermal properties and surface features of the separator vary depending on the characteristics of the ceramic powders applied to the separator, it is crucial to manufacture ceramic powders optimized for the separator's performance. In this study, we evaluated the characteristics of three types of α-alumina (A-1, A-2, and A-3) produced with varying dispersant contents and milling times, in addition to commercial α-alumina (AES-11). Subsequently, the optimized powders (A-3) were coated onto the separator using an aqueous binder for comparison with the characteristics of an AES-11 coated separator and an uncoated PE separator. The A-3 coated separator improved electrolyte wettability with a low contact angle (44.69°) and increased puncture strength (538 gf). Furthermore, it exhibited excellent thermal stability, with a shrinkage value of 5.64% when exposed to 140℃ for 1 hour, compared to the AES11 coated separator (6.09%) and the bare PE separator (69.64%).