• Journal of Sensor Science and Technology
• /
• v.32 no.5
• /
• pp.328-333
• /
• 2023

This study experimentally verified the etch rate of the SiO₂ sacrificial layer etching process with a single etch hole using vapor-phase hydrogen fluoride (VHF) etching. To fabricate small-sized polysilicon etch holes, both circular and triangular pattern masks were employed. Etch holes were fabricated in the polysilicon thin film on the SiO₂ sacrificial layer, and VHF etching was performed to release the polysilicon thin film. The lateral etch rate was measured for varying etch hole sizes and sacrificial layer thicknesses. Based on the measured results, we obtained an approximate equation for the etch rate as a function of the etch hole size and sacrificial layer thickness. The etch rates obtained in this study can be utilized to minimize structural damage caused by incomplete or excessive etching in sacrificial layer processes. In addition, the results of this study provide insights for optimizing sacrificial layer etching and properly designing the size and spacing of the etch holes. In the future, further research will be conducted to explore the formation of structures using chemical vapor deposition (CVD) processes to simultaneously seal etch hole and prevent adhesion owing to polysilicon film vibration.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1254-1257
• /
• 2004

Comparative study on the effects of $H_2$ vs. $O_2$ plasma pretreatment of gate oxide on the degradation phenomenon of p-channel low-temperature polysilicon (LTPS) thin-film transistors (TFTs) were performed. After high drain current stress (HDCS) with $V_{gs}$ = $V_{ds}$, the p-channel TFTs pretreated by $O_2$ plasma showed increased immunity to the degradation of device characteristics such as threshold voltage and maximum field effect mobility because of the higher binding energy of Si-O bond than that of Si-H bond. The investigation of degradation phenomenon of these parameters with the applied power suggests that self-heating can be the major cause of degradation of polysilicon TFTs.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.2
• /
• pp.261-266
• /
• 1998

This paper describes the fabrication and characterization of dual-polysilicon gated surface channel 0.1$\mu\textrm{m}$ CMOSFETs using BF2 and arsenic as channel dopants. We have used and LDD structure and 40${\AA}$ gate oxide as an insulator. To suppress short channel effects down to 0.1$\mu\textrm{m}$ channel length, shallow source/drain extensions implemented by low energy implantation and SSR(Super Steep Retrograde) channel structure were used. The threshold voltages of fabricated CMOSFETs are 0.6V. The maximum transconductance of nMOSFET is 315${\mu}$S/$\mu\textrm{m}$, and that of pMOSFET is 156 ${\mu}$S/$\mu\textrm{m}$. The drain saturation current of 418 ${\mu}$A/$\mu\textrm{m}$, 187${\mu}$A/$\mu\textrm{m}$ are obtained. Subthreshold swing is 85mV/dec and 88mV/dec, respectively. DIBL(Drain Induced Barrier Lowering) is below 100mV. In the device with 2000${\AA}$ thick gate polysilicon, depletion in polysilicon near the gate oxide results in an increase of equivalent gate oxide thickness and degradation of device characteristics. The gate delay time is measured to be 336psec at operation voltage of 2V.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.490-495
• /
• 1999

In 0.18 $\mu \textrm m$ LOGIC device, the etch rate of NMOS polysilicons is different from that of PMOS polysilicons due to the state of polysilicon to manufacture gate line. To control the etch profile, we tested the ratio of $Cl_2$/HBr gas and the total chamber pressure, and also we reduced Back He pressure to get the vertical profile. In the case of manufacturing the gate photoresist line, we used Bottom Anti-Reflective Coating (BARC) to protect refrection of light. As a result we found that $CF_4O_2$ gas is good to etch BARC, because of high selectivity and good photoresist line profile after etching BARC. in the results of the characterization of plasma damage to the antenna effect of gate oxide, NO type thin film(growing gate oxide in 0, ambient followed by an NO anneal) is better than wet type thin film(growing gate oxide in $0_2+H_2$ ambient).

• Proceedings of the KIEE Conference
• /
• 1989.11a
• /
• pp.122-126
• /
• 1989

A composite polycide struoture consisting of refractory metal and noble metal silicide film on top of polysilicon bas been considered as a replacement for polysilicon as a gate electrode and Interconnect line in MOSFET integrated circuits. In this paper presents divice characteristics of NOS with $TiSi_2/n^+$polyoide and $CoSi_2/n^+$polycide gate. Also, evaporated Ti,Co films on polysilicon has been annealed by RTA and furnace annealing in $N_2$ abient at temperature of $400^{\circ}C-1000^{\circ}C$. The Ti-,Co-silioide formation is characterized by 4-point probe, silicide growth rate and Its reproductivity bas been examined by SEM.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.2
• /
• pp.66-72
• /
• 1995

Using the Si/SiGe layer grown by solid source molecular beam epitaxy(SSMBE) on the LOCOS-patterned wafers, an emitter-base self-aligned hterojunction biplar transistor(HBT) with the polysilicon-emitter and the silicon germanium(SiGe) base has been fabricated. Trech isolation process, planarization process using a chemical-mechanical poliching, and the selectively implanted collector(SIC) process were performed. A titanium disilicide (TiSi$_{2}$), as a base electrode, was used to reduce an extrinsic base resistance. To prevent the strain relaxation of the SiGe epitaxial layer, low temperature (820${^\circ}C$) annealing process was applied for the emitter-base junction formation and the dopant activation in the arsenic-implanted polysilicon. For the self-aligned Si/SiGe HBT of 0.9${\times}3.8{\mu}m^{2}$ emitter size, a cut-off requency (f$_{T}$) of 17GHz, a maximum oscillation frequency (f$_{max}$) of 10GHz, a current gian (h$_{FE}$) of 140, and an emitter-collector breakdown voltage (BV$_{CEO}$) of 3.2V have been typically achieved.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.3
• /
• pp.126-134
• /
• 1996

Tungsten silicide films were deposited on the phosphorus-doped poly-Si/SiO$_{2}$/Si-substrates by LPCVD (low pressue chemical vapor deposition). The formation and various properties of tungsten silicide processed by furnace annealing in N$_{2}$ ambient were evaluated by using XRD. AFM, 4-point probe and SEM. And the redistribution of phosphorus atoms has been observed by SIMS. The crystal structure of the as-deposited tungsten silicide films were transformed from the hexagonal to the tetragonal structure upon annealing at 550.deg. C. The surface roughness of tungsten polycide films were found to very smoothly upon annelaing at 850.deg. C and low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide low phosphorus concentration in polysilicon layer. The sheet resistance of tungsten polycide films are measured to be 2.4 .ohm./ㅁafter furnace annealing at 1100.deg. C, 30min. It was found that the sheet resistance of tungsten polycide films upon annealing above 1050.deg. C were independant on the phosphorus concentration of polysilicon layer and furnace annealing times. An out-diffusion of phosphorus impurity through tungsten silicide film after annealing in $O_{2}$ ambient revealed a remarkably low content of dopant by oxide capping.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.127-127
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.46-47
• /
• 1993

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1485-1488
• /
• 1997

The capacity of memory chip has increased vert quickly and 64MDRAM becomes main product in semiconductor manufacturing lines consists of many sequential processes, including etching process. although it needs direct sensing of wafer state for the accurae detching, it depends on indirect esnsing and sample test because of the complexity of the plasma etching. This equipment receives the inner light of etch chamber through the viewport and convets it to the voltage inetnsity. In this paper, EDP voltage signal has a new role to detect etching failure. First, we gathered data(EPD sigal, etching time and etchrate) and then analyzed the relationships between the signal variatin and the etch rate using two neural network modeling. These methods enable to predict whether ething state is good or not per wafer. For experiments, it is used High Density Inductive coupled Plasma(HDICP) ethcing equipment. Experiments and results proved to be abled to determine the etching state of wafer on-line and analyze the causes by modeling and EPD signal data.