• Fashion & Textile Research Journal
• /
• v.5 no.3
• /
• pp.273-282
• /
• 2003

Effect of fixation methods and relaxation treatment on the flame retardant(FR) and physical properties of MDPP/HMM treated cotton weft-knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of cotton weft-knitted fabric with MDPP/HMM. As the results, 1. Swelling agent and wet fixation method helps FR agent penetrate the fiber efficiently. Interlock showed relatively higher values of LOI than single jersey. 2. Interlock showed relatively higher values of bending rigidity(B), shear rigidity(G) and coefficient of friction(MIU) than those of single jersey before and after flame resistant treatment. 3. An increase in internal volume of cotton fiber by relaxation treatment increased the bending rigidity(B), shear rigidity(G) and compressional energy(WC). 4. The cotton weft-knitted fabric treated wet fixation, which crossliked FR agent efficiently, showed higher bending rigidity, shear rigidity(G) and lower compressional energy(WC). Retention of swelling ability of cotton weft-knitted fabrics treated with MDPP/HMM, which increased the internal volume of cotton weft-knitted fabric, showed lower bending rigidity.

• Polymer(Korea)
• /
• v.27 no.1
• /
• pp.40-45
• /
• 2003

In this work, the effect of different contents of $Fe_3O_4$ and temperature variation on the electrical conductivity ($\sigma$) in the polar acrylonitrile butadiene rubber (NBR)/$Fe_3O_4$ (magnetite) mixture system was investigated. It was found that the percolation threshold concept holds true for the conductive particle-filled composites where $\sigma$ indicates a nearly sharp increase when the concentration of magnetite in the mixture exceeds 22%. The temperature dependence of $\sigma$ was thermally activated below and at the percolation threshold ($P_c$). Magnetite acted as reinforcing and conductive filler for NBR. At room temperature and higher voltages, the electrical current was proportional to the square of voltage ($I{\propto}V^2$) for the composites which contain 30 phr of magnetite. Moreover, it was shown that the composites with magnetite of 50 phr showed the highest tensile strength and elongation at break, which was due to the formation of optimal physical interlock and crosslinking. The results of 100%, 200%, and 300% Young moduli said that the moduli are largely correlated with reinforcement effect of magnetite and viscosity of the blends from torque curve.

• Journal of the Korean Society of Safety
• /
• v.22 no.6
• /
• pp.1-6
• /
• 2007

A Recently elevator accidents were occurred and increased due to carelessness of user and violent behavior. The accident of door detachment in elevator platform by electronic motor scooter show a example of safety concerns and insensibility for safety awareness. In this report, we review the cause of accident of door detachment in elevator platform by electronic motor scooter, and show some suggestions of preventing from the safety concerns about this case.

• Textile Coloration and Finishing
• /
• v.18 no.3 s.88
• /
• pp.23-30
• /
• 2006

The bending properties, wrinkle resistance, and fabric retention behaviors of cotton knitted fabrics in the wale and course directions were studied for their dependence upon resin finishing, knit structure, and washing cycles. Stiffness, wrinkle recovery angles, and dimensional stability were investigated before and after resin finishing and laundering. It has been found that any change in the physical properties of the knitted fabrics with respect to knit structure and fabric directions are related to accompanying modifications to the state of the fiber properties. The decrease of fabric shrinkage rates and wrinkle recovery properties from increasing laundering cycles is related with resin incorporated on the fiber surface. This study shows that resin finishing on knitted fabrics can be performed only to improve fabric retention properties with reduced wrinkle recovery properties.

• Journal of the Korea Safety Management & Science
• /
• v.8 no.1
• /
• pp.17-26
• /
• 2006

Basis frame-work's base in a semiconductor industry have gas, chemical, electricity and various facilities in bring to it. That it is a foundation by fire, power failure, blast, spill of toxicant huge by large size accident human and physical loss and damage because it can bring this efficient, connect with each kind mechanical, physical thing to prevent usefully need that control finding achievement factor of human factor of human action. Large size accident in a semiconductor industry to machine and human and it is involved that present, in system by safety interlock defect of machine is conclusion for error of behaviour. What is not construing in this study, do safety in a semiconductor industry to do improvement. Control human error analyzes in human control with and considers mechanical element and several elements. Also, apply achievement factor using O'conner Model by control method of human error. In analyze by failure mode effect using actuality example.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.433-439
• /
• 2005

This paper describes a reinforced concrete crack model, which utilizes a strain decomposition technique. The strain decomposition technique enables the explicit inclusion of physical behavior across the cracked concrete surface such as aggregate interlock and dowel action rather than intuitively defining the shear retention factor. The proposed concrete crack model is integrated into the commercial finite element software ABAQUS shell elements through a user-supplied material subroutine. The FE results have been compared to experimental results reported by other researchers. The proposed bridge FE model is capable of predicting the initial cracking load level, the ultimate load capacity, and the crack pattern with good accuracy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.585-590
• /
• 1999

There is still a lack of knowledge and modelling relating to shear behaviour in reinforced concrete beams. The reason is that shear loading leads to complicated physical mecanisms, such as interlock action, dowel action, etc. Therefore, It is difficult that we make the ideal model of shear behaviour, while Truss model theory has been made good use of shear design because of simplicity and reasonableness. In this study, 6 T-type reinforced concrete beams were designed and made based on the two truss models, i.e, the plasticity truss model and the compatibility truss model, to observe shear strength of concrete and stress distribution of stirrups. 6 beams test pieces were tested with the following testing parameters. 1) specified concrete strength ; 270kg/$\textrm{cm}^2$, 400kg/$\textrm{cm}^2$ 2) with and without the steel fiber.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.9_10 s.146
• /
• pp.1274-1284
• /
• 2005

Effect of fixation methods and relaxation treatment on the dimensional stability and physical properties of MDPPA/HMM treated cotton knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of 4 kinds of cotton knitted fabric with MDPPA/HMM. Then these fabrics were washed 10 times. As a result, In swelling treatment on 10G showed relatively higher value of length shrinkage than 14G. Length and width shrinkage were increased by initial washing treatment and no further change was shown after 6 washing cycles. After 10 washing cycles, length and width shrinkage decreased. The KES standardized basic value of B/W, 2HB/W and bursting strength of interlock were relatively larger than those of single jersey. The values of B/W and 2HB/W of cotton knitted fabrics were increased by relaxation and washing treatment but were decreased by swelling treatment. In addition, the bursting strength of the cotton knitted fabrics was decreased after fusing, washing and relaxation treatment.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.119-124
• /
• 2001

Dimethyl terephthalate (DMT). 1.4-butanediol (1.4-BD) and poly (tetramethylene ether) glycol (PTMG) in the molecular weight of 2000 (g/mol) were used to synthesize poly(ether-b-ester) thermoplastic elastomers (TPEEs). The final copolymers were annealed to improve thermal stability at elevated temperatures and mechanical properties. This study showed that as the proportion of soft segment increases melting temperature and degree of crystallinity of TPEEs decrease constantly. In case of mechanical properties like flexural strength and flexural elastic modulus. $35-PTMG^{2000}$ indicates the highest values due to more efficient physical interlock.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.6
• /
• pp.104-113
• /
• 2011

While converging USN Services, a single physical infrastructure can be used in several services and in several physical infrastructures can make up a single service. Therefore the physical infrastructure and service have to manage separately for effective convergence of USN Services. However, established Identification Scheme is not suitable to distinguish various services that USN provides. This paper suggests USN Service Identification Scheme that can be separated and managed. Through USN Service Identification Scheme suggested, firstly, it is possible to obtain Service Identification Scheme utilizing various technology such as RFID TAG, QR Code, radio broadcasting, etc. because it is possible to process USN Service Identification Scheme. Secondly, it is easy to mange the service, develope the user application program and interlock with established USN Standard technique as view from service provider. Thirdly, it is possible to manage systematically USN Service. Fourthly, users can search USN Service easily, so it can contribute actively for invigoration of USN service. This thesis, firstly, has analyzed about standard related USN Service and USN Identification Scheme. Secondly, this has suggested brand-new USN Service Identification Scheme based on established USN Identification Scheme.