• Journal of Mechanical Science and Technology
• /
• 제16권5호
• /
• pp.609-618
• /
• 2002

In practical designs, most of the multidisciplinary problems have a large-size and complicate design system. Since multidisciplinary problems have hundreds of analyses and thousands of variables, the grouping of analyses and the order of the analyses in the group affect the speed of the total design cycle. Therefore, it is very important to reorder and regroup the original design processes in order to minimize the total computational cost by decomposing large multidisciplinary problems into several multidisciplinary analysis subsystems (MDASS) and by processing them in parallel. In this study, a new decomposition method is proposed for parallel processing of multidisciplinary design optimization, such as collaborative optimization (CO) and individual discipline feasible (IDF) method. Numerical results for two example problems are presented to show the feasibility of the proposed method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.818-823
• /
• 2000

In practical design studies, most of designers solve multidisciplinary problems with complex design structure. These multidisciplinary problems have hundreds of analysis and thousands of variables. The sequence of process to solve these problems affects the speed of total design cycle. Thus it is very important for designer to reorder original design processes to minimize total cost and time. This is accomplished by decomposing large multidisciplinary problem into several multidisciplinary analysis subsystem (MDASS) and processing it in parallel. This paper proposes new strategy for parallel decomposition of multidisciplinary problem to raise design efficiency by using genetic algorithm and shows the relationship between decomposition and multidisciplinary design optimization (MDO) methodology.

• 제어로봇시스템학회논문지
• /
• 제22권10호
• /
• pp.847-852
• /
• 2016

In this paper, important design parameters for parallel kinematic robots are defined, paying special attention to machining errors which may cause kinematic errors at the end effector of a robot. The kinematic effects caused by each design parameter, as well as their upper/lower limits, are analyzed here. To do so, we have developed a novel software program to compute kinematic errors by considering its defined design parameters. With this program, roboticists designing parallel kinematic robots can understand the important design parameters for which upper/lower allowances have to be strictly controlled in the design process. This tactic can be used for the design of high-speed, parallel kinematic robots to reduce the design/manufacturing costs and increase kinematic precision.

• 제어로봇시스템학회논문지
• /
• 제10권7호
• /
• pp.590-596
• /
• 2004

A passivity-based dynamic output feedback controller design is considered for a finite collection of non-square linear systems. Design of a single controller for a set of plants i.e. simultaneous stabilization is an important issue in the area of robust control design. We first determine a squaring gain matrix and an additional dynamics that is connected to the systems in a feedforward way, then a static passivating control law is designed. Consequently, the actual feedback controller will be the static control law combined with the feedforward dynamics. A necessary and sufficient condition for the existence of the parallel feedforward compensator is given by the static output feedback formulation. In contrast to the previous result [1], a technical condition for constructing the parallel feedforward compensator is removed by proposing a new type of the parallel compensator.

• Journal of Power Electronics
• /
• 제13권3호
• /
• pp.437-446
• /
• 2013

This paper proposes a design scheme for an LCL-filter used for the three-parallel operation of the power converters in high-capacity wind turbines. The designs of the power devices and grid connected filter are difficult due to the high level voltages and currents in huge-capacity wind turbines. To solve these problem, this paper presents three-parallel operation and LCL-filter design techniques optimized by parallel operation. Furthermore, the design of an inverter side inductance of the LCL-filter is discussed in detail considering the switching modulation method. Simulation and experimental results demonstrate the validity of the designed filter and wind turbines.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2009년도 정보통신설비 학술대회
• /
• pp.215-218
• /
• 2009

In this paper, Dual-band bandpass filter studied design using Parallel Coupled SIR(Stepped Impedance Resonator). This Dual-band bandpass filter design SIR of half-wavelength by Parallel-coupled type that is available to RFID system and Changed structure in Meander form by size reduce. Because seen Dual-band bandpass filter is designed so that is applicable for frequency 433MHz and 2.45GHz of RFID system is very wide distance between two pass-band, establish 433MHz by fundamental frequency and controlled 2.45GHz by 2st spurious resonance frequency bandstop filter of 1st spurious resonance frequency and Parallel coupled SIR Combine to remove 1st spurious resonance frequency.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.886-898
• /
• 2015

The design feasibility of a micro unidirectional DC transmission system based on an input-parallel output-parallel (IPOP) converter is analyzed in this paper. The system consists of two subsystems: an input-parallel output-series (IPOS) subsystem to step up the DC link voltage, and an input-series output-parallel (ISOP) subsystem to step down the output voltage. The two systems are connected through a transmission line. The challenge of the delay caused by the communication in the control system is addressed by introducing a ring communication structure, and its influence on the control system is analyzed to ensure the feasibility and required performance of the converter system under practical circumstances. Simulation and experiment results are presented to verify the effectiveness of the proposed design.

• 로봇학회논문지
• /
• 제5권4호
• /
• pp.359-366
• /
• 2010

This study proposes the design method for the robot rotation arm which the end effector that is connected in end of the arm keeps parallel motion even though the robot arm rotates. So far, most robot arm rotates together the end effector when the arm rotates. For this, this study proposes the mechanism that the arm is linked to each 4 parallel link so that rotation is possible by 4 pins, and the rotation arm connects 2 joints of diagonal line direction to a link in each 4 joint for rotation, and designs so that can change length of the link. For verification of design, this study targeted that develop the rotation arm for medical examination that use in ophthalmology. It is important that a medical robot offers comport to patient and design compactly so that medical examination and treatment space may can be defined enough. It is designed so that all drive elements may be positioned on interior of the arm and optimization of design for main parts was carried out in this study for this. The robot arm which is developed in this study manufactured to use by medical phoropter arm, and got good result by an experiment. The robot rotation arm which is proposed in this study is judged to contribute very effectively in case use of a medical robot arm for medical examination and treatment, also the robot arm which the end effector that is connected in the end of the arm needs to keep parallel motion. And, the robot arm which is developed in this study made an application as license.

• 전기학회논문지
• /
• 제57권1호
• /
• pp.40-45
• /
• 2008

This paper presents an optimal design of a permanent magnet actuator(PMA) using a parallel genetic algorithm. Dynamic characteristics of permanent magnet actuator model are analyzed by coupled electromagnetic-mechanical finite element method. Dynamic characteristics of PMA such as holding force, operating time, and peak current are obtained by no load test and compared with the analyzed results by coupled finite element method. The permanent magnet actuator model is optimized using a parallel genetic algorithm. Some design parameters of vertical length of permanent magnet, horizontal length of plunger, and depth of permanent magnet actuator are predefined for an optimal design of permanent magnet actuator model. Furthermore dynamic characteristics of the optimized permanent magnet actuator model are analyzed by coupled finite element method. A displacement of plunger, flowing current of the coil, force of plunger, and velocity of plunger of the optimized permanent magnet actuator model are compared with the results of a primary permanent magnet actuator model.

• 조명전기설비학회논문지
• /
• 제23권3호
• /
• pp.24-29
• /
• 2009

In case of the optimization problems that have many design variables, the conventional genetic algorithms(GA) fall into a trap of local minima with high probability. This problem is called the premature convergence problem. To overcome it, the parallel genetic algorithms which adopt the migration mechanism have been suggested. But it is hard to determine the several parameters such as the migration size and the migration interval for the parallel GAs. Therefore, we propose a new method to determine the migration interval automatically in this paper. To verify its validity, it is applied to some traditional mathematical optimization problems and is compared with the conventional parallel GA. It is also applied to the optimal design of the brushless DC motor for an electric wheel chair which is a real world problem and has five design variables.