• Structural Engineering and Mechanics
• /
• v.30 no.6
• /
• pp.713-732
• /
• 2008

Serviceability and durability of the concrete members can be seriously affected by the corrosion of steel rebar. Carbonation front and or chloride ingress can destroy the passive film on rebar and may set the corrosion (oxidation process). Depending on the level of oxidation (expansive corrosion products/rust) damage to the cover concrete takes place in the form of expansion, cracking and spalling or delamination. This makes the concrete unable to develop forces through bond and also become unprotected against further degradation from corrosion; and thus marks the end of service life for corrosion-affected structures. This paper presents an analytical model that predicts the weight loss of steel rebar and the corresponding time from onset of corrosion for the known corrosion rate and thus can be used for the determination of time to cover cracking in corrosion affected RC member. This model uses fully the thick-walled cylinder approach. The gradual crack propagation in radial directions (from inside) is considered when the circumferential tensile stresses at the inner surface of intact concrete have reached the tensile strength of concrete. The analysis is done separately with and without considering the stiffness of reinforcing steel and rust combine along with the assumption of zero residual strength of cracked concrete. The model accounts for the time required for corrosion products to fill a porous zone before they start inducing expansive pressure on the concrete surrounding the steel rebar. The capability of the model to produce the experimental trends is demonstrated by comparing the model's predictions with the results of experimental data published in the literature. The effect of considering the corroded reinforcing steel bar stiffness is demonstrated. A sensitivity analysis has also been carried out to show the influence of the various parameters. It has been found that material properties and their inter-relations significantly influence weight loss of rebar. Time to cover cracking from onset of corrosion for the same weight loss is influenced by corrosion rate and state of oxidation of corrosion product formed. Time to cover cracking from onset of corrosion is useful in making certain decisions pertaining to inspection, repair, rehabilitation, replacement and demolition of RC member/structure in corrosive environment.

• Proceedings of the Korean Magnestics Society Conference
• /
• 1999.04a
• /
• pp.136-137
• /
• 1999

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.04a
• /
• pp.124-125
• /
• 2002

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.446-451
• /
• 2009

Reliability evaluations of linear low density polyethylene (LLDPE) pipe with respect of thermal exposure time have been investigated in accordance with RS M 0042, which is a reliability standard for polymer pipe. As the thermal exposure time is prolonged, a progressive increase, until 250 days, in tensile strength and a slight increase in hardness are observed, while a proportional decrease in elongation at break is showed. These results can be explained by the increase of crystallinity, followed by the increase of crosslinking density, chain scission and the decrease in chain mobility, due to thermal oxidation as the exposure time increases. Long term hydrostatic pressure test result implies the existence of transition point from ductile to brittle fracture. Oxidation induction time (OIT) test is employed to monitor the thermo-oxidative degradation of LLDPE pipe. This result shows that after the exposure time is 250 days, the depletion of antioxidants added in LLDPE pipe occurs. An empirical equation as function of exposure time, under $100^{\circ}C$ thermal-degradation condition, is proposed to assess the remaining amount of antioxidants owing to thermo-oxidative degradation. Fourier transform infrared spectroscopy results show the increase of carbonyl (-C=O) and hydroxyl (O-H) function groups on the surface of thermally exposed LLDPE pipe. This result suggests that the hydrocarbon groups locally undergo the oxidation on the LLDPE surface due to thermal-degradation.

• Korean Journal of Soil Science and Fertilizer
• /
• v.29 no.3
• /
• pp.243-248
• /
• 1996

To find out the oxidation process of potential acid sulfate soil(PASS) along with time. the PASS were treated with lime and ammonia water to adjust soil pH in laboratory column condition. pH range of PASS showed 6.5 to 7.5. however, complete oxidized PASS by $H_2O_2$ showed 2.1 to 2.5. After pilling the PASS under the natural condition. oxidation occured slowly from surface of the pilled soil. The oxidation of PASS proceeded slowly when the soil was in submerged condition. but quickly in dried condition. The content of sulfide-sulfur in PASS sharply decreased after exposing to the air and the decreasing rate was greater in dried than in submerged condition. The content of sulfate-sulfur continuously decreased in submerged condition. but increased in dried condition. Contents of $Fe^{+{+}}$ and $Al^{+{+}}$ in PASS were generally increased with time and the increasing rate was greater in submerged than in dried condition. Liming to PASS was slowly acting to pH change and ammonia water caused fast pH change within a short period of time. The contents of sulfate-sulfur and exchangeable aluminum in drainage water decreased with time and the contents of sulfide-sulfur and ferrous iron were increased.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1340-1349
• /
• 2012

Increasing the oxidation of fat through exercise is the recommendable method for weight control. Preceding researches have proposed increase in the usage of fat during exercise in stabilized state and under maximum exertion through aerobic training. However, such researches require additional equipment for gas analysis in order to measure the caloric value or gas exchange of subjects during exercise. Such equipments become highly restrictive for those exercise and cause substantially higher cost. According to this, we have presented the method of estimating the maximal fat oxidation point through changes in LF & HF which reflects changes in heart rate and the autonomic nervous system in order to induce exercise for a less restrictive and efficient fat oxidation than existing methods. We have conducted exercise stress test on subject with similar exercise abilities, and have detected the changes in heart rate and changes in LF & HF by measuring changes in fat oxidation and measuring ECG signals at the same time through a gas analyzer. Changes in heart rate and HRV of the subjects during exercising was detected through only the electrocardiographic signals from exercising and detected the point of maximum fat oxidation that differs from person to person. The experiment was carried out 16 healthy males, and used Modified Bruce Protocol, which is one of the methods of exercise stress test methods that use treadmill. The fat oxidation amount during exercise of all the subjects showed fat oxidation of more than 4Fkcal/min in the exercise intensity from about 5 minutes to 10 minutes. The correlation between the maximal fat oxidation point obtained through gas analysis and the point when 60% starts to be relevant in the range from -0.01 to 0.01 seconds for values of R-R interval from changes in heart rate had correlation coefficients of 0.855 in Kendall's method and in Spearman's rho, it showed significant results of it being p<0.01 with 0.950, respectively. Furthermore, in the changes in LF & HF, we have determined the point where the normalized area value starts to become the same as the maximal fat oxidation point, and the correlation here showed 0.620 in Kendall and 0.780 in Spearma of which both showed significant results as p<0.01.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.8
• /
• pp.26-34
• /
• 1997

To develop ultrathin gate oxide for ULSI MOSFETs, for the first time, we fabricated MOS capacitors with 65.angs. thick initial oxide grown by high pressure oxidation (HIPOX) at 700.deg. C in 5 atmosphere $O_{2}$ ambient and then followed by rapid thermal nitridation (RTN) in N$_{2}$O ambient. The dielectric breakdown fields of the initial HIPOX oxide are 13.0 MV/cm and 13.8MV/cm for negative and positive gate bias, respectively and are dependent on nitridation temeprature and time.The lifetimes of the HIPOX oxides extractd by TDDB method are 1.1*10$^{8}$ sec and 3.4 * 10$^{9}$ sec for negative and positive stress current, respectively. The lifetime of the HIPOX oxide dfor negative stress current increases with nitridation time in N$_{2}$O ambient at 1100.deg.C, reaching maximum value stress curretn increases with nitridation time in N$_{2}$O ambient at 1100.deg. C reacing maximum value of 1.2*10$^{9}$ sec for 30 sec of nitridation time, and then subsequently decreases at the longer nitridation time. The lifetimes of the nitrided-HIPOX oxides are longer than 10 years when nitridations are carried out longer than about 50 sec and 12 sec at 1000.deg. C, and 1100.deg. C, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.4
• /
• pp.833-837
• /
• 2012

This paper proposes a DRAM data retention time enhancement method that minimizes silicon loss and undercut at STI sidewall by reducing the SC1 (Standard Cleaning) time. SC1 time optimization debilitates the parasitic electric field in STI's top corner, which reduces an inverse narrow width effect to result in reduction of channel doping density without increasing the subthreshold leakage of cell Tr. Moreover, it minimizes the electric field in depletion area from cell junction to P-well, increasing yield or data retention time.

• Journal of the Korean Ceramic Society
• /
• v.32 no.2
• /
• pp.227-233
• /
• 1995

By using homestyle microwave oven, Al-Al2O3 powder mixture could be oxidized and sintered into Al2O3 body. The differences in powder characteristics among the differently processed raw materials affect the oxidation and sintering behaviours, and these effects were more pronounced in case of microwave oven than of conventional furnace. Al-Al2O3 powder mixture was oxidized and sintered within 2hrs, which could save both processing time and energy.

• Journal of Environmental Science International
• /
• v.15 no.7
• /
• pp.659-667
• /
• 2006

This research aims at applicability of adsorption process in order to satisfy the restricted Effluent Quality Standards for dyeing wastewater. The dyeing wastewater treated by biological process with carrier imbedded microorganisms was directly applied to the activated carbon adsorption in Process A, The dyeing wastewater treated by Fenton oxidation for the effluent of biological process was applied to the adsorption in Process B. It was found that the optimum conditions of adsorption with granular activated carbon are $20^{\circ}C$ and 120 minutes for the batch experiment. Langmuir equation was fitted better than Freundlich equation to the experimental data. The breakthrough time of adsorption column was determined by color rather than $COD_{Mn}$ for both Process A and Process B. The results revealed that the breakthrough time of adsorption for two processes was extended by the treatment of Fenton oxidation for dyeing wastewater treated by biological treatment than the direct application of dyeing wastewater treated by the biological treatment. Adsorption process can be applied in order to meet the restricted Effluent Quality Standards for dyeing wastewater.