• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.174-185
• /
• 2005

This paper presents the design, fabrication, and testing results of a dual stage actuator system for a fine positioning of magnetic heads in magnetic disk drives. A novel rotary microactuator which is electrostatically driven and utilized as a secondary actuator was designed. The stator and rotor electrodes in the microactuator was revised to have the optimal shapes and hence produces much higher rotational torque compared with the conventional comb-shape electrodes. The microactuators were successfully fabricated using SoG(silicon on glass) processing technology, which is known as being cost-effective. The fabricated microactuator has the structural thickness of $45{\mu}m$ with the gap width of approximately $3{\mu}m$. The dynamic characteristic of microactuator/slider assembly was investigated, and its natural frequency and DC gain were measured to be 3.4kHz and 32nm/V, respectively. The microactuator/slider assembly was integrated into a HDD model V10 of Samsung Electronics Co. and a dual servo algorithm was tested to explore the tracking performance of dual stage actuator system where the LDV signals instead of magnetic head signals were used. Experimental results indicate that this system achieves the tracking accuracy of 30nm. This value corresponds to a track density of 85,000 track per inch(TPI), which is about 3 times greater than that of current hard disk drives.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.6
• /
• pp.561-566
• /
• 2017

The weight reduction design process of tension links could be studied based on the variation of tension, bending and torsional stiffness after substituting STKM11A steels with aluminum alloys (A356) with tensile strength of 245 MPa. The existed I-beam type link component may have a weak point for loads applied from a special direction. Therefore, it was investigated to the optimal shape of the link component that could withstand loads from all directions and at the same time reduce weight. Various types of link shapes were designed and analyzed, and the optimized shape was found. The optimized design can reduce over 40% of the original steel link weight, and it could be suggested for light-weight design guides and safe design conditions for the development of tension links.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.74-81
• /
• 2014

In this study, it was conducted to improve the performance of stud of Steel Plate Concrete(SC) walls subjected to bending moment. Non-linearity of contact interface, connection, and material properties were considered in finite element modeling of SC wall. In order to validate the analytical model, furthermore, a foregoing laboratory experiment was simulated by FEM, so that comparison between the measured result and the analysis result have be done. The size of the analytical model was determined by reflecting various references and the analyses were performed according to various shapes and arrangements of stud. Additionally, the validity of the model considering the related provisions in the KEPIC SNG standard was also considered. As a result, the optimal shape and spacing of studs was proposed through this numerical analysis and standard verification.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.177-182
• /
• 2007

The effects of three fuselage head shapes and nonplanar ground surface on the aerodynamic characteristics of FAST fuselages are investigated using a boundary element method. Wind tunnel test is also performed to validate the present method and to identify the wall effect on the frictional drag which cannot be analyzed using the present method. It is found that the channel has an effect of increasing the lift of those investigated fuselages. The optimal head shape depends on the design conditions of the FAST and its guideway channel. Comparing the calculated induced drag with the measured total drag, it can be concluded that the profile drag is independent of the ground height. Thus, the present numerical method can be applied to the conceptual design of the high-speed ground transporters if only the profile drag of the vehicle in free flight is assumed to be known.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.2
• /
• pp.147-153
• /
• 2014

The purpose of this paper is to examine the roll damping characteristics by bilge keels on the fishing vessel. Unlike other degree of freedom motions, roll motion is highly nonlinear. However the quantitative evaluation of roll damping combined with waves is very important for the fishing vessel. To reduce roll motion, roll motion stabilizers such as a bilge keel is used due to easy made and cheap cost rather than anti-rolling tank and fin-stabilizer. Authors paid attention to the shape of bilge keel and waves to grasp the roll damping for the fishing vessel and studied about the difference of tendencies of roll angle following the shapes of bilge keel. The model ship was the offshore large purse seiner and four types of bilge keel were used. The data from the experiments were provided and analyzed to investigate the rolling characteristics of the model ship being affected by the wave height, wave period and bilge keel shape. The results of the study showed that three types of the bilge keel have little effective, but only one has an effect on the roll damping. So bilge keel shape and its attachment method need to be a future study for the practical use in fishing vessel.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.1
• /
• pp.39-45
• /
• 1989

Many mechanical systems including ships and/or offshore structures have poor dynamic response characteristics such as undesirable natural frequencies and undesirable mode shapes. It is mandatory to redesign the structure. In this paper a procedure for the dynamic redesign of an undamped structural system is presented. The method which uses a penalty function with a penalty term containing error in equilibrium for a given vibration mode may have a shortcoming. This method includes unconstrained eigenvector degrees of freedom as unknowns. In the work developed here, only constrained mode shape changes are used in the solution procedure, resulting in a reduction of the unnecessary calculations. Among the set of equations which characterizes the redesign of the structural systems, the under constrained problem is discussed here and formulated as an optimization problem, with an optimal criterion such as minimum change or minimum structural weight of the system. Four simple numerical applications illustrate the efficiency of the method. The method can be applied to the vibration problems of ships and/or offshore structures with an implementation of the commercial FE codes.

• Solar Energy
• /
• v.18 no.3
• /
• pp.185-195
• /
• 1998

The high viscosity of a LiCl(lithium chloride) solution as an absorbent in a solar energy regenerator causes a channeling phenomenon on the solar powered absorber plate surface when the solution is trickling down for regenerating itself. As this channeling phenomenon affects badly the heat and mass transfer, it is pertinent that this phenomenon be studied. Since regenerating performance of the solar energy regenerator depends on how the solution uniformly flows on the plate surface, an experiment on the structure of the plate surface for a model regenerator was conducted. Various shapes and structures of the plat surface down which the LiCl solution trickled were tested, and it was found that a tiered surface showed the highest water evaporation rate leaving more potential energy concentrating LiCl on the plate. It was also observed that the water evaporation rate depended largely on the pitch and height of the disturbing rods. In addition, the wider the contact area is and the longer the solution's flow time, the better the solar energy regenerator's performance.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.3 no.4
• /
• pp.274-285
• /
• 2011

The supercavitating vehicle is an underwater vehicle that is surrounded almost completely by a supercavity to reduce hydrodynamic drag substantially. Since the cruise speed of the vehicle is much higher than that of conventional submarines, the drag force is huge and a buckling may occur. The buckling phenomenon is analyzed in this study through static and dynamic approaches. Critical buckling load and pressure as well as buckling mode shapes are calculated using static buckling analysis and a stability map is obtained from dynamic buckling analysis. When the finite element method (FEM) is used for the buckling analysis, the solver requires a linear static solver and an eigenvalue solver. In this study, these two solvers are integrated and a consolidated buckling analysis module is constructed. Furthermore, Particle Swarm Optimization (PSO) algorithm is combined in the buckling analysis module to perform a design optimization computation of a simplified supercavitating vehicle. The simplified configuration includes cylindrical shell structure with three stiffeners. The target for the design optimization process is to minimize total weight while maintaining the given structure buckling-free.

• The KIPS Transactions:PartA
• /
• v.14A no.1 s.105
• /
• pp.31-38
• /
• 2007

Code Optimization is converting to a code that is equivalent to given program but more efficient, and this process is processed in Code Optimizer. This paper designed and processed Code Optimizer Generator that automatically generates Code Optimizer. In other words Code Optimizer is automatically generated for DFA Pattern Matching which finds the optimal code for the incoming pattern description. DFA Pattern Matching removes redundancy comparisons that occur when patterns are sought for through normalization process and improves simplification and structure of pattern shapes for low cost. Automatic generation of Code Optimization for DFA Pattern Matching eliminates extra effort to generate Code Optimizer every time the code undergoes various transformations, and enables formalism of Code Optimization. Also, the advantage of making DFA for optimization is that it is faster and saves cost of Code Optimizer Generator.

• Elastomers and Composites
• /
• v.47 no.4
• /
• pp.341-346
• /
• 2012

Injection molding is one of the widely used polymer processing operations. It is being used for not only conventional injection molding but gas injection molding, water injection molding, and injection compression molding. Injection compression molding involves injection and compression operation, and it gives uniform physical property and high dimensional quality of product. In this study, injection compression characteristics for various product shapes have been investigated by computer simulation. Product containing side wall showed not much effective in injection compression molding since wall thickness direction was perpendicular to the compression direction. Uniform and low shrinkage was observed in injection compression molding comparing conventional injection molding. Subsequently injection compression molding can be used for molding precise product. Optimal injection compression molding condition was obtained using design of experiment for plastic lens and the results were compared with conventional injection molding.