• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6C
• /
• pp.623-628
• /
• 2006

This paper addresses the frequency offset estimation problem in the presence of the timing error for OFDM systems. When the timing error exists, the correlation value used for the frequency offset estimation could be reduced significantly due to the timing error, resulting in considerable degradation in estimation performance. In this paper, using the coherence phase bandwidth (CPB) and a threshold, a novel frequency offset estimation scheme is proposed and based on which, an efficient timing error estimation scheme is also proposed for the re-estimation of the frequency offset. The performance comparison results show that the proposed frequency offset estimation scheme is not only more robust to the timing error but also has less computational complexity, as compared with the conventional schemes. It is also demonstrated by simulation that theproposed timing error estimation scheme gives a reliable estimate of the timing error.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1593-1600
• /
• 2015

This paper proposes a novel compensation algorithm of current offset error for single-phase linear compressor in home appliances. In a half-bridge inverter, current offset error may cause unbalanced DC-link voltage when the DC-link is comprised of two serially connected capacitors. To compensate the current measurement error, the synchronous reference frame transformation is used for detecting the measurement error. When an offset error occurs in the output current of the half-bridge inverter, the d-axis current has a ripple with frequency equal to the fundamental frequency. With the use of a proportional-resonant controller, the ripple component can be removed, and offset error can be compensated. The proposed compensation method can easily be implemented without much computation and additional hardware circuit. The validity of the proposed algorithm is verified through experimental results.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.26-32
• /
• 2008

The performance of an analog winner-take-all(WTA) circuit is affected by the corner error and the offset error. Despite the fact that the corner error can be reduced with large transconductance of the transistor, the offset error caused by device mismatch has not been completely studied. This paper presents the complete offset error analysis, and proposes low offset design guidelines and an offset cancellation scheme. The experimental results show good agreement with the theoretical analysis and the drastic improvement of the offset error.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.5
• /
• pp.402-409
• /
• 2022

In vector-controlled drive systems, the current measurement offset error causes unwanted torque ripple, resulting in speed and torque control performance degradation. The current measurement offset error is caused by various factors, including thermal drift. This study proposes a simple DC offset error compensation method for a surface permanent magnet motor based on a disturbance observer. The disturbance observer is designed in the stationary reference frame. The proposed method uses only the measured current and machine parameters without additional hardware. The effect of parameter variations is analyzed, and the performance of the current measurement offset error compensation method is validated using simulation and experimental results.

• Journal of Drive and Control
• /
• v.16 no.2
• /
• pp.72-79
• /
• 2019

Despite the development of electronic components and microprocessors, hydraulic actuators are still being applied in various applications. In some applications, there is a desire to apply a hydraulic actuator with a relatively small position error to the system. Various studies have been conducted to reduce the position error of hydraulic actuators. In this paper, the position error of the hydraulic actuator when the hydraulic oil pressure is supplied is defined as the offset generated by the servo valve, and the method for correcting the servo valve offset has been studied. A method for compensating the servo valve offset was proposed and it was verified through experiments that the position error of the hydraulic actuator was reduced. We also compared the servo valve offset correction method and controller using the PID control and disturbance observer used to reduce the position error of the hydraulic actuator. No-load test and load test were performed to confirm the performance of the servo valve offset correction method. The results of the study were compared with those obtained by using the disturbance observer and PID control.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.11
• /
• pp.68-76
• /
• 2014

This paper presents an offset error compensation algorithm for the accurate phase angle of the grid voltage in single-phase grid-connected inverters. The offset error generated from the grid voltage measurement process cause the fundamental harmonic component with grid frequency in the synchronous reference frame phase lock loop (PLL). As a result, the grid angle is distorted and the power quality in power systems is degraded. In addition, the dq-axis currents in the synchronous reference frame and phase current have the dc component, first and second order ripples compared with the grid frequency under the distorted grid angle. In this paper, the effects of the offset and scaling errors are analyzed based on the synchronous reference frame PLL. Particularly, the offset error can be estimated from the integrator output of the synchronous reference frame PLL and compensated by using proportional-integral controller. Moreover, the RMS (Root Mean Square) function is proposed to detect the offset error component. The effectiveness of the proposed algorithm is verified through simulation and experiment results.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.6
• /
• pp.1707-1713
• /
• 2016

This paper proposes a dc error compensation algorithm using dq-synchronous coordinate transform digital phase-locked-loop in single-phase grid-connected converters. The dc errors are caused by analog to digital conversion and grid voltage during measurement. If the dc offset error is included in the phase-locked-loop system, it can cause distortion in the grid angle estimation with phase-locked-loop. Accordingly, recent study has dealt with the integral technique using the synchronous reference frame phase-locked-loop method. However, dynamic response is slow because it requires to monitor one period of grid voltage. In this paper, the dc offset error compensation algorithm of the improved response characteristic is proposed by using the synchronous reference frame phase-locked-loop. The simulation and the experimental results are presented to demonstrate the effectiveness of the proposed dc offset error compensation algorithm.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.323-326
• /
• 2004

In this study, the inspection path which is considered to free collision is generated by offset surface. When the inspection is executed, the consideration of machine dynamic error increases a precision. Dynamic error is measured on CNC machine bed changing of weight work price. Offset surface is safety space about collision. Because the danger of probe-collision is excluded in Offset surface, it is possible to rapid feed of probe and reduced inspection time. The Program which is possible to simulate using CAIP and is confirmed through actual experiment.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.4
• /
• pp.19-27
• /
• 2004

The characteristic evaluation of A/D converter is to measure the linearity of the converter. The evaluation of the linearity is to measure the DNL, INL, gain error and offset error in the various test parameters of A/D converter. Generally, DNL and INL are to be measured by the Histogram Test Algorithm in the DSP-based ATE environment. And gain error and offset error are to be measured by the calculation equation of the measuring algorithm. It is to propose the new Concurrent Histogram Test Algorithm for the test of the housekeeping A/D converter used in the CDMA cellular phone. Using the proposed method, it is to measure the DNL, INL, gain error and offset error concurrently and to show the measured results.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.140-146
• /
• 2005

In this paper, we proposed the frequency offset compensation algorithm and tracking algorithm which could improve the accumulated phase error for HDR-WPAN system. The proposed frequency offset compensation technique estimated each sample phase error by autocorrelation characteristics of CAZAC sequence, estimated phase error multiple each sample in a symbol, and finally compensated for the frequency offset. After frequency offset compensation using two steps, coarse and fine frequency offset, tracking algorithm have to use to compensate for the accumulated phase error. Because there is no pilot symbol in payload, more phase rotation occurred in received signal constellations due to the accumulated phase error as the payload length increase. Tracking algorithm compensates for a cumulative phase error ${\theta}$ between payload data.