• 한국전기전자재료학회논문지
• /
• 제33권1호
• /
• pp.16-20
• /
• 2020

In this study, a patterning method using self-aligned nanostructures was introduced to fabricate GaN-based fin-gate HEMTs with normally-off operation, as opposed to high-cost, low-productivity e-beam lithography. The honeycomb-shaped fin-gate channel width is approximately 40~50 nm, which is manufactured with a fine width using a proposed method to obtain sufficient fringing field effect. As a result, the threshold voltage of the fabricated device is 0.6 V, and the maximum normalized drain current and transconductance of Gm are 136.4 mA/mm and 99.4 mS/mm, respectively. The fabricated devices exhibit a smaller sub-threshold swing and higher Gm peak compared to conventional planar devices, due to the fin structure of the honeycomb channel.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.323-323
• /
• 2012

We present ferroelectricity of Bi-doped ZnO film probed by piezoresponse force microscopy (PFM), which is one of the Scanning Probe Microscopy techniques. Perovskite ferroelectrics are limited to integration of devices into semiconductor microcircuitry due to hard adjusting their lattice structure to the semiconductor materials. Transition metal doped ZnO film is one of the candidate materials for replacing the perovskite ferroelectrics. In this study, ferroelectric characteristics of the Bi-doped ZnO grown by pulsed laser deposition were probed by PFM. The polarization switching and patterning of the ZnO films were performed by applying DC bias voltage between the AFM tips and the films with varying voltages and polarity. The PFM contrast before and after patterning showed clearly polarization switching for a specific concentration of Bi atoms. In addition, the patterned regions with nanoscale show clearly the local piezoresponse hysteresis loop. The spontaneous polarization of the ZnO film is estimated from the local piezoresponse based on the comparison with LiNbO3 single crystals.

• 반도체디스플레이기술학회지
• /
• 제9권4호
• /
• pp.19-23
• /
• 2010

Nanoimprint lithography (NIL) is one of the most versatile and promising technology for micro/nano-patterning due to its simplicity, high throughput and low cost. Recently, one of the major trends of NIL is large-area patterning. Especially, the research of the application of NIL to TFT-LCD field has been increasing. Technical difficulties to keep the uniformity of the residual layer, however, become severer as the imprinting area increases. In this paper we performed a numerical study for a large area NIL (the $2^nd$ generation TFT-LCD glass substrate ($370{\times}470$ mm)) by using finite element method. First, a simple model considering the surrounding wall was established in order to simulate effectively and reduce the computing time. Then, the volume of fluid (VOF) and grid deformation method were utilized to calculate the free surfaces of the resist flow based on an Eulerian grid system. From the simulation, the velocity fields and the imprinting pressure during the filling process in the NIL were analyzed, and the effect of the surrounding wall and the uniformity of residual layer were investigated.

• 한국전기전자재료학회논문지
• /
• 제34권4호
• /
• pp.262-268
• /
• 2021

For the past several decades, various next-generation patterning methods have been developed to obtain well-designed nano-to-micro structures, such as imprint lithography, nanotransfer printing (nTP), directed self-assembly (DSA), E-beam lithography, and so on. Especially, nTP process has much attention due to its low processing cost, short processing time, and good compatibility with other patterning techniques in achieving the formation of high-resolution functional patterns. To transfer functional patterns onto desirable substrates, the use of soft materials is required for precise replication of master mold. Here, we introduce a simple and practical nTP method to create highly ordered structures using various polymeric replica materials. We found that polymethyl methacrylate (PMMA), polystyrene (PS), and polyvinylpyridine (PVP) are possible candidates for replica materials for reliable duplication of Si master mold based on systematic analysis of pattern visualization. Furthermore, we successfully obtained well-defined metal and oxide nanostructures with functionality on target substrates by using replica patterns, through deposition and transfer process. We expect that the several candidates of replica materials can be exploited for effective nanofabrication of complex electronic devices.

• 대한기계학회논문집B
• /
• 제36권12호
• /
• pp.1171-1176
• /
• 2012

실리콘 기판 위에 플라즈마 기상층착법을 이용하여 합성된 탄소나노튜브를 화학적인 방법이나 전자빔 혹은 이온빔과 같은 진공 챔버 내에서의 공정없이 펨토초레이저를 이용하여 선택적으로 패터닝 하는 방법을 구현하였다. 플라즈마 기상층착법으로 합성된 탄소나노튜브는 수직성장이 가능하며 탄소나노튜브 간의 간격을 조절하여 성장이 가능하다. 이러한 장점으로 전계방출소자, 바이오센서 등의 응용을 위하여 이용되는 합성 방법이다. 이러한 응용을 위하여 선택적으로 나노튜브를 제거하고 탄소나노튜브 끝의 촉매금속을 제거하는 것이 응용의 효율을 높이는데 매우 중요하다. 본 연구에서는 탄소나노튜브의 전기적, 구조적 특성에 영향을 줄 수 있는 화학적인 방법을 사용하지 않고 펨토초레이저를 사용하여 패터닝과 촉매금속을 제거하는 방법을 구현하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.272-273
• /
• 2013

Some living thingsuse micro- or nano- structures for living in nature. Scientists and engineers made efforts to mimic them, and they succeeded in making new types of applications. They used 'Namib desert beetle' to self-filling device by moisture harvesting and 'lotus leaf' to self-cleaning device by water repelling. 'Namib desert beetle' and lotus leaf have micro-patterns on their surface, which consists of hydrophobic or hydrophilic materials [1]. Moreover, micro-patterns on the surface make self-filling or self-cleaning property enhanced because of the surface roughness. Surface roughness enhances wettability [2]. Micro-pattern is a significant factor to make the surface be functional, so we want to make new types of functional surface by micro-patterning. In this work,we make several functional micro-patterns (radial, line, and dot arrays) using maskless lithography and analyze the characteristics of each micro-pattern. In order to analyze and understand surface characteristics, micro-patterns with varying sizes are investigated. All experiments are proceeded on mr-DWL5 photo resists coated on silicon wafers in same condition. All the experiments have demonstrated good performances about hydrophobic or hydrophilic property corresponding to their material and structural combinations. In radial micro-pattern, although the surface is flat, water drops on hydrophilic radial pattern can be convergent to a middle point and water drops on hydrophobic radial pattern can be divergent from the middle point. In line array micro-pattern, water drops can roll off along only one direction in parallel with the line arrays. Such phenomena might be mainly caused by the local change of surface roughness. From these results, controlling the movement and direction of water drops is made feasible without introducing a slope, which can potentially be used for new types of applications.

• 마이크로전자및패키징학회지
• /
• 제31권3호
• /
• pp.18-23
• /
• 2024

나노임프린트 리소그래피(Nanoimprint lithography, NIL)는 저렴한 공정비용으로 고해상도 패턴을 제조할 수 있는 장점을 가지고 있기 때문에 마이크로 크기부터 나노스케일까지 패턴을 형성하는데 많이 사용되고 있다. 그러나, 대부분의 NIL 공정 기술은 기본적으로 임프린트용 레지스트 사용이 필요하고, 자외선, 열과 같은 외적인 요소 또한 필요로 하기 때문에, 타겟 소재를 패터닝하기 위해서 식각공정 또는 금속 증착 등의 추가적인 후공정이 요구된다. 그리고, 유연 필름이나 굴곡이 있는 소재를 패터닝 하기에 어려움이 있다. 본 연구에서는, 유연한 자성고무 복합재(rubber magnet composite, RMC) 기판 표면에 마이크로/나노 수준의 패턴을 상온에서 식각 공정 없이 형성할 수 있는 극압 임프린트 리소그래피(extreme pressure imprint lithography, EPIL) 공정을 소개하고자 한다. EPIL 기술은 금속, 고분자, 세라믹과 같은 다양한 재료의 표면에 직접적이고 영구적인 변형을 통해 초미세 구조물을 대면적으로 형성할 수 있는 공정으로서, 본 연구에서는 RMC 필름에 적용하여 서브 마이크로 크기의 패턴 형성이 가능함을 보여준다. 우리는 스트론튬계 페라이트와 염소화폴리에틸렌으로 구성된 유연한 RMC 기판 표면에 마이크로/나노 스케일의 다양한 패턴 크기 및 형상을 갖는 균일한 구조물을 형성할 수 있는 공정 및 결과물을 보여주고자 한다. RMC 필름 표면 상 미세한 패턴구현이 가능한 EPIL 공정은 미세한 자기 방향의 변화 및 제어를 요구하는 첨단 전자기소자 부품 제조에 널리 적용될 수 있을 것으로 기대한다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 동계학술발표회 논문집
• /
• pp.133-134
• /
• 2009

Cold temperature development (CTD) of electron beam (EB) patterned resists and subsequent dry etching were investigated for fabrication of nano-patterned Niobium (Nb). Bulky Nb fims on GaAs substrates were deposited with EB evaporation. Line patterns on Nb cathode were fabricated by EB patterning and reactive ion etching (RIE). Size deviations of nano-sized line patterns from CAD designed patterns are dependent on the EB total exposure, but it can be improved by CTD of EB-exposed resist. Line patterns of 10 to 300 nm widths of EB-exposed resist patterns were drawn under various exposure conditions of $0.2{\mu}s$/dot (total 240,000 dot) with a constant current (50 pA). Compared with room temperature development (RTD), the CTD improves pattern resolution due to the suppression of backscattering effect. RIE with $CF_4$ was performed for formation of several nano-sized line patterns on Nb. Each EB-resist patterned samples with RTDs and CTDs were etched with two different $CF_4$ gas pressures of 5 Pa. Nb etching rate increases while GaAs (or ZEP) etching rate decreases as the chamber pressure increases. This different dependent of the etching rate on the $CF_4$ pressure between Nb and GaAs (or ZEP) has a significant meaning because selective etching of nano-sized Nb line patterns is possible without etching of the underlying active layer.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.3.2-3.2
• /
• 2011

In recent years, inkjet printing technology has received significant attention as a micro/nanofabrication technique for flexible printing of electronic circuits and solar cells, as well for biomaterial patterning. It eliminates the need for physical masks, causes fewer environment problems, lowers fabrication costs, and offers good layer-to-layer registration. To fulfill the requirements for use in the above applications, however, the inkjet system must meet certain criteria such as high frequency jetting, uniform droplet size, high density nozzle array, etc. Existing inkjet devices are either based on thermal bubbles or piezoelectric pumping; they have several drawbacks for flexible printing. For instance, thermal bubble jetting has limitations in terms of size and density of the nozzle array as well as the ejection frequency. Piezoelectric based devices suffer from poor pumping energy in addition to inadequate ejection frequency. Recently, an electrohydrodynamic (EHD) printing technique has been suggested and proposed as an alternative to thermal bubble or piezoelectric devices. In EHD jetting, a liquid (ink) is pumped through a nozzle and a strong electric field is applied between the nozzle and an extractor plate, which induce charges at the surfaces of the liquid meniscus. This electric field creates an electric stress that stretches the meniscus in the direction of the electric field. Once the electric field force is larger than the surface tension force, a liquid droplet is formed. An EHD inkjet head can produce droplets smaller than the size of the nozzle that produce them. Furthermore, the EHD nano-inkjet can eject high viscosity liquid through the nozzle forming tiny structures. These unique features distinguish EHD printing from conventional methods for sub-micron resolution printing. In this presentation, I will introduce the recent research results regarding the EHD nano-inkjet and the printing system, which has been applied to solar cell or thin film transistor applications.

• 한국진공학회지
• /
• 제19권4호
• /
• pp.300-306
• /
• 2010

소수성 고분자를 사용하여 제작한 마이크로구조에 금 나노입자를 마스크로 이용하는 반응성이온식각(RIE: Reactive Ion Etching)을 적용하여 초소수성을 갖는 마이크로-나노 혼성구조를 제작하였다. 소수성 고분자로는 PFPE (perfluoropolyether bisurethane methacrylate)를 사용하였으며 마이크로 단일구조는 PDMS (polydimethylsiloxane) 몰드를 사용하는 스탬핑 방식으로 제작하였다. 다양한 형태로 제작한 PFPE 마이크로 단일구조와 마이크로-나노 혼성구조의 표면 접촉각을 측정하여 표면 미세구조에 따른 소수성의 변화를 관찰하였다. 마이크로 단일구조의 경우 접촉각은 안정적인 값을 보이지 못하였으나 단일 구조에 나노입자를 사용한 식각을 적용해 나노구조가 형성됨에 따라 $150^{\circ}$ 이상의 접촉각을 갖는 초소수성 표면이 매우 높은 재현성으로 용이하게 형성되었다.