• Journal of radiological science and technology
• /
• v.34 no.1
• /
• pp.51-58
• /
• 2011

The aim of the study is to analyze the dose delivery error depending on the depth variation according to target positions and arc trajectories by comparing the simulated treatment planning with the actual dose delivery in conformal arc therapy. We simulated the conformal arc treatment planning with the three target positions (center, 2.5 cm, and 5 cm in the phantom). For the experiments, IMRT body phantom (I’mRT Phantom, Wellhofer Dosimetry, Germany) was used for treatment planning with CT (Computed Tomography, Light speed 16, GE, USA). The simulated treatment plans were established by three different target positions using treatment planning system (Eclipse, ver. 6.5, VMS, Palo Alto, USA). The radiochromic film (Gafchromic EBT2, ISP, Wayne, USA) and dose analysis software (OmniPro-IMRT, ver. 1.4, Wellhofer Dosimetry, Germany) were used for the measurement of the planned arc delivery using 6 MV photon beam from linear accelerator (CL21EX, VMS, Palo Alto, USA). Gamma index (DD: 3%, DTA: 2 mm) histogram and dose profile were evaluated for a quantitative analysis. The dose distributions surrounded by targets were also compared with each plans and measurements by conformity index (CI), and homogeneity index (HI). The area covered by 100% isodose line was compared to the whole target area. The results for the 5 cm-shifted target plan show that 23.8%, 35.6%, and 37% for multiple conformal arc therapy (MCAT), single conformal arc therapy (SCAT), and multiple static beam therapy, respectively. In the 2.5 cm-shifted target plan, it was shown that 61%, 21.5%, and 14.2%, while in case of center-located target, 70.5%, 14.1%, and 36.3% for MCAT, SCAT, and multiple static beam therapy, respectively. The values were resulted by most superior in the MCAT, except the case of the 5 cm-shifted target. In the analysis of gamma index histogram, it was resulted of 37.1, 27.3, 29.2 in the SCAT, while 9.2, 8.4, 10.3 in the MCAT, for the target positions of center, shifted 2.5 cm and 5 cm, respectively. The fail proportions of the SCAT were 2.8 to 4 times as compared to those of the MCAT. In conclusion, dose delivery error could be occurred depending on the target positions and arc trajectories. Hence, if the target were located in the biased position, the accurate dose delivery could be performed through the optimization of depth according to arc trajectory.

• Journal of Nutrition and Health
• /
• v.35 no.4
• /
• pp.454-463
• /
• 2002

The purpose of this study was to investigate the relationship among the anthropometric measurements, body composition indices, biochemical indices and serum leptin level of obese school children. The study was conducted on 97 elementary school children from 4-5th grade residing in Daegu and Kyungbuk area. Obesity was defined as fat percentage that exceed 25% of body fat mass. The prevalence of obesity of subject was 58.3% for male and 54.1% for female. The mean value of height, weight, body composition indices and biochemical indices of obese group were significantly higher than those of control group. The leptin level was significantly different in obese group but showed no difference by gender. The differences of leptin level were according to adiposity and BMI in obese subjects. Multiple regression analysis data showed that the BMI and body fat mass may influence on the leptin level of subject. Also, these data revealed the leptin resistance in obese children and relationship between leptin level and various factors including anthropometric measurements, body composition and biochemical indices. Additional research should be necessary to assess the mechanism of leptin resistance in obese children.

• The korean journal of orthodontics
• /
• v.39 no.5
• /
• pp.300-309
• /
• 2009

Objective: The purpose of this study was to evaluate the correlation between menton deviation and dental compensation in facial asymmetry. Methods: Tooth axis and distance of first molar and canine to the reference plane were investigated by cone-beam computerized tomography. The subjects consisted of 50 patients with asymmetric mandibles (male 21, female 29, mean age 24.3 years). Control groups were also assessed (male 11, female 9, mean age 25.6 years). Nine measurements (5 linear measurements and 4 angular measurements) were measured in order to evaluate the correlation between menton deviation and the linear and angular difference of first molar and canine in the deviated and none-deviated sides using the defined MPR images. The differences between deviated and non-deviated side, according to menton deviation, were statistically analyzed using stepwise multiple regression analysis. Results: From the result, Menton deviation was negatively correlated with mandibular first molar's angular measurement (${\Delta\angle}LM6$-Mn plane (dev.-ndev.)) and positively with maxillary fist molar's angular measurement (${\Delta\angle}UM6$-FH plane (dev.-ndev.)) (p < 0.01). Two angular measurements (${\Delta\angle}LM6$-Mn plane (dev.-ndev.), ${\Delta\angle}UM6$-FH plane (dev.-ndev.)) explained the variability in menton deviation with a significant $r^2$ value of 0.589. Conclusions: This study suggests that the tooth axis of upper and lower first molars leans towards the deviated side of Menton when there is mandibular asymmetry with Menton deviation.

• Journal of Veterinary Clinics
• /
• v.31 no.6
• /
• pp.495-501
• /
• 2014

The objective of this study was to evaluate the differences and reproducibility of Hounsfield unit (HU) value and volume measurements on different computed tomography (CT) scanner types and different collimations by using a gelatin phantom. The phantom consisting of five synthetic simulated calculus spanning diameters from 3.0 mm to 12.0 mm with 100 HU was scanned using a two-channel multi-detector row CT (MDCT) scanner, a four-channel MDCT scanner, and two 64-channel MDCT scanners. For all different scanner types, the thinnest possible collimation and the second thinnest collimation was used. The HU values and volumes of the synthetic simulated calculus were independently measured three times with minimum intervals of 2 weeks and by three experienced veterinary radiologists. ANOVA and Scheff$\acute{e}$ test for the multiple comparison were performed for statistical comparison of the HU values and volumes of the synthetic simulated calculus according to different CT scanner types and different collimations. The reproducibility of the HU value and volume measurements was determined by calculating Cohen's k. The reproducibility of HU value and volume measurements was very good. HU value varied between different CT scanner types, among different beam collimations. However, there was not statistically significant difference. The percent error (PE) decreased as the collimation thickness decreased, but the decrease was statistically insignificant. In addition, no statistically significant difference in the PEs of the different CT scanner types was found. It can be concluded that the CT scanner type insignificantly affects HU value and the volumetric measurement, but that a thinner collimation tends to be more useful for accurate volumetric measurement.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.18
• /
• pp.7897-7907
• /
• 2014

Background: There is paucity of studies defining the prevalence of non-communicable disease (NCD) risk factors in Saudi Arabia despite the surging epidemic of obesity, change in dietary habits and sedentary lifestyle. Objectives: This cross-sectional study aimed to assess the prevalence of NCDs risk factors among employees at King Faisal University in Al Hassa, Saudi Arabia and to determine the possible correlates for clustering of NCDs risk factors among them. Materials and Methods: All employees were invited to participate; the World Health Organization STEPwise approach was used for data collection which consisted of a personal interview to collect socio-demographic characteristics, NCD history, tobacco use, vegetables and fruit consumption, and physical activity (PA), followed by anthropometric measurements namely weight, height and waist circumference and blood pressure measurements, subjects were finally subjected to biochemical tests with determination of fasting plasma glucose, serum triglycerides, cholesterol and high density lipoproteins. Results: Of the surveyed employees (n=691), daily current smokers accounted for 22.7%. 94.9%, 95.1% and 86% consumed < 5 servings per day of vegetables, fruits and both fruits and vegetables respectively, 73% were physically inactive, 64% were overweight or obese, 22.1% had hypertension, and 21.5% were diabetics. Elevated cholesterol levels were found in 36.6%, low high density lipoproteins in 36.8%, and elevated triglycerides in 36.1%. Only 3% had no NCD risk factors, and 57.6% had ${\geq}3$ factors. Multivariate logistic regression showed that gender (being male, adjusted odds ratio 'aOR'=1.51), aged ${\geq}50$ years (aOR=3.06), < college education (aOR=1.75), current smokers (aOR=2.37), being obese (aOR=6.96) and having a low PA level (aOR=4.59) were the significant positive predictors for clustering of NCD risk factors. Conclusions: Over fifty percent of the studied university's employees had multiple (${\geq}3$) NCD risk factors. Screening and health promotion initiatives should be launched at least targeting the modifiable factors to avert the excessive risk for cardiovascular disease, diabetes mellitus and several types of cancers.

• Korean Journal of Human Ecology
• /
• v.7 no.3
• /
• pp.15-33
• /
• 2004

A precise understanding of the human form in static pose serves as the basis of designing clothing. When the human body is in motion, however, even an article of clothing designed to fit the human form in static pose can pull and change, thus restricting the body. In order to increase the fit of the clothing, which may be termed the second skin, its form and measurements therefore must be determined in correlation not only with the formal characteristics of the human body, in static pose but also with its functional characteristics in motion, as caused by the movements of the human body. In this study, the motion factor was selected as the primary basis for designing slacks with good fit in both static and moving states. By indentifying the areas in which lower limb movement cause significant changes in body surface lines, we suggest several application methods for designing slacks. Using unmarried female university students aged 18 - 24 as subjects, a total of 32 body surface categories (15 body surface lines and 17 body surface segment lines) were measured in one static and 9 movement poses. In particular, expansion and contraction levels and rates were measured and used in the analysis. The analysis first involved the calculation of the average measurement per body part in body surface line in static pose as well as of the average expansion and contraction levels and rates in 9 lower limb movements. Two-way MANOVA and multiple comparison analysis (Tukey) were conducted on movements and individual somatotypes regarding measurement per body part and expansion and contraction rates. Body parts whose measurements of body surface lines differed significantly in body surface line in static pose versus in movement were then identified. The results of this study are as follows. First, changes in body surface lines caused by lower limb movements were significant in all body surface lines of the lower trunk, both horizontal and vertical, with the exception of abdomen girth, midway thigh girth, ankle girth, hip length, and posterior knee girth. Second, significantly expanded 10 body surface lines in moving pose were detected and illustrated in table 4. These body parts should be studied in designing or pattern designing, especially for close-fitting pants, in using stretch fabric, and in sensory evaluation of good fit during movement.

• Tunnel and Underground Space
• /
• v.23 no.4
• /
• pp.288-296
• /
• 2013

In this study, a total of 13 mines were finally selected as study subjects and field measurements were conducted. Thereafter, calculations of thermodynamic natural ventilation were attempted using spread sheets and solutions for natural ventilation of mine types with multiple vertical shafts were obtained. Based on the results, natural ventilation of each mine was quantified. In addition, changes in natural ventilation energy (NVE) and natural ventilation pressure (NVP) were estimated assuming mine deepening and the resultant values were applied to mine conditions to observe changes in flow rates. Natural ventilation pressure in domestic mines is generally calculated to be in a range of 5 Pa~300 Pa. Although NVP increases as the depth increases, resistance also increases. Therefore, as the depth increases, flow rates show a tendency of converging on a certain value because of the relationship between NVP and mine resistance. Natural ventilation using shafts with depth differences is effective up to depths of 200~300 m. However, flow rate change rates resulting from NVP are small at depths deeper than approximately 200~300 m. Therefore, if a mine is deepened over 300 m, NVP will become insufficient and thus additional pressure obtained through mechanical ventilation will be necessary.

• Progress in Medical Physics
• /
• v.17 no.4
• /
• pp.187-191
• /
• 2006

The purpose of this study was to measure the dose distribution from the moving phantom for the respiratory motion. The phantom for TLD measurement was designed and built for this study based on the multiple plates for placing TLD and film. The TLDs may be inserted at 3 mm intervals in each TLD plate. For the measurements, TLD plate was inserted into the phantom at 1.5 cm ($d_{max}$) depth, and phantom was allowed to move in SI directions in the range of 1 to 2 cm with 0.5 cm interval for 6 MV X-ray beams. Penumbra and FWHM were measured at both moving state and compared stationary. It was found that penumbra increased 0.71 cm at stationary and 2.10 cm at moving state in 2 cm movement, and that FWHM are 7.52 cm for stationary state and 7.02 cm for moving state (2 cm movement). In this study, film was used to compared with TLD results of measurements and simitar results were observed. Therefore, it is expected that TLD moving phantom may be useful for the treatment of tumors that move due to the respiratory motion.

• Journal of Yeungnam Medical Science
• /
• v.15 no.1
• /
• pp.135-142
• /
• 1998

Maternal weight gain during pregnancy has been consistently associated with infant birth weight and pregnancy outcome. Our purpose was to determine the relationship between maternal weight gain pattern and birth weight. Consequently, maternal weight gain is monitored carefully and is encouraged during prenatal care in order to improve pregnancy outcome. Our study group included both 424 uncomplicated women and infant delivered at the Yeungnam University Hospital between 1993-1996. All recorded prenatal weight gain measurements were used to estimate maternal trimester weight gain, pattern of gain (based on low versus not-low gain at each trimester), and total gain at delivery. Multiple linear regression analysis was used to assess the relationship between these weight gain measurements and fetal birth weight. Each kilogram of maternal gain in the first, second, and third trimesters was associated with statistically related to the increase in fetal birth weight by 31.3, 19.0, and 24.5g, respectively. When compaired with the pattern of gain that was not low in any trimester, patterns with low gain in the first trimesters were associated with significant decreases in birth weight, but no important change in birth weight was seen for the group whose gains were not low in the first trimester. The results suggest that specific patterns of maternal weight gain, particularly weight gain during the first trimester, are related to fetal birth weight.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.33-40
• /
• 2020

Various studies have been conducted on the structural health monitoring using optical fiber. Optical fibers can be used to measure multiple and distributed strain. Among the optical fiber sensors, FBG sensor has advantages of dynamic response measurement and high precision, but the number of measurement points is limited. Distributed fiber sensors, represented by distributed Brillouin sensors, usually have more than 1000 measurement points, but the low sampling rate makes dynamic measurements impossible. In this study, a hybrid nerve sensor system using only the advantages of the FBG sensor and the distributed Brillouin sensor has been proposed. Laboratory experiments were performed to verify the proposed system, and the accuracy and reproducibility were verified by comparing with commercial sensors. Applying the proposed system, dynamic response ambient measurements are used to evaluate the global state of the structure. When an abnormal condition is detected, the local condition of the structure is evaluated by static response measurement using the distributed measurement system. The proposed system can be used for efficient structural health monitoring.