• Journal of Korea Foundry Society
• /
• v.27 no.1
• /
• pp.42-47
• /
• 2007

Vacuum molding process(V-process) has several benefits such as a lower total production cost and a high quality casting comparing to the conventional sand molding. Influence of the gating design on the molten metal flow was investigated in this study. General criteria for the gating design of the castings and commercial codes for the flow and solidification analysis were used to attain the optimized gating design in V-process. Though mold cavity was filled smoothly under the low initial velocity of molten metal, molten metal dashed against the upper part of the mold before the completion of the mold filling with higher initial molten metal velocity and fell soon. This phenomenon may affect collapsing the mold shape, however it is thought that the possibility of burning out of the vinyl by the molten metal is not so high because vinyl is coated with refractory material.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.1
• /
• pp.47-54
• /
• 2008

As the demands of environment protection increases, the pulp mold container is developed to substitute for EPS (expanded polystyrene) as a shock absorbing packaging material. The water-absorbing ratio and mechanical properties such as tensile strength and compressive strength of pulp mold are important factors to evaluate its shock absorbing characteristics. Influences of mixing ratios of ONP (old newspaper) and OCC (old corrugated container) on physical properties of pulp mold were investigated at various conditions of temperature and relative humidity. The optimum mixing ratio of ONP and OCC was also searched based on physical properties. The results showed that when relative humidity was increased from 60% to 90%, the water absorption ratio of pulp mold increased significantly, tensile strength decreased 20$\sim$30%, and compressive strength decreased 10$\sim$20%. In addition, the optimum mixing ratio of ONP and OCC was found to be 50%:50%.

• Korean Journal of Metals and Materials
• /
• v.49 no.7
• /
• pp.577-582
• /
• 2011

The newly developed ${\alpha}-case$ controlled mold material for Ti investment castings was suggested in this research. The $Al_2O_3$ mold containing interstitial $TiO_2$ and substitutional $Ti_3Al$ was manufactured by the reaction between $Al_2O_3$ and Ti. It is obvious that as the $TiO_2$ and $Ti_3Al$ content in the mold surface were increased, the depth of the interfacial reaction was significantly reduced. In addition, substitutional $Ti_5Si_3$ in the mold surface owing to the reaction between Ti and $SiO_2$ from the binder was effective for ${\alpha}-case$ reduction. Therefore, the ${\alpha}-case$ reduction was accomplished by the diffusion barrier effect of interstitial $TiO_2$, substitutional $Ti_3Al$ and $Ti_5Si_3$.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.4
• /
• pp.47-50
• /
• 2021

Nanoimprint lithography (NIL) has revolutionized the fabrications of electronics, photonics, optical and biological devices. Among all the NIL processes, roll-to-roll nanoimprinting is regarded best for having the attributes of low cost, continuous, simple, and energy-efficient process for nanoscale device fabrication. However, large-area printing is limited by the master mold deformation. In this study, a finite element model (FEM) has been constructed to assess the deformation of the roll mold adhesively wrapped on the carbon fiber reinforced material (CFRP) base roll. This study also optimizes the deformations in the metallic roll mold with respect to nip-forces applied in the printing process of nano-fabrication on large scale. The numerical simulations were also conducted to evaluate the deflection in roll mold assembly due to gravity. The results have shown decreasing trend of the deformation with decreasing nip-force. Also, pressure uniformity of about 40% has been optimized by using the current numerical model along with an acceptable deflection value in the vertical axis due to gravity.

• Design & Manufacturing
• /
• v.6 no.1
• /
• pp.73-78
• /
• 2012

The aim of this dissertation is inferring factors controlling the complex strain behavior of the material and the characteristics of the Fine-Blanking in the most narrow area at the shear zone where we are performing the Fine-Blanking. And also this is for inspecting and presenting their uses and the possibilities to make the results data based in order to utilize easily. Therefore, to analyze of shere zone's strain behaviour, the Fine-Blanking process need to be modelled defining the quadratic-nodded and axi-symmetrical elements as the problems of large deformation axi-symmetry and the non-linear contact. For the method of inputting strain-stress values of the material, the piece-wise linear technics were used, the Implicit-Finite Element method also used making balance of forces on each step by the long intervals, calculates and converges many times was done. The materials used for the analysis was the Steel SNCM220 5.5mm respectively. As the result of FEM analysis, we know that shear stress value in the beginning of punch penetration is distributed widely and done high both in the center of the late-thickness and on the both sides centering around shear strain zone as the punch penetration is increasing. Also.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1416-1422
• /
• 2001

The objective of this work was to characterize mechanical properties of thermoplastic composites with various forming conditions in compression molding. Randomly oriented long glass fiber reinforced polypropylene(PP) was used in this work. The composite materials contained 20%, 30%, and 40% glass fiber by weight. Compression molding was conducted at various mold temperatures and charge sizes. The temperatures on the mold surface and at the material in the mid-plain were monitored during the molding. Differential Scanning Calorimeter was used to measure crystallinity at both in-side and out-side of the sheet material. Crystallinity at each temperature was also measured by X-ray diffractometer. Dimensional stability was studied at various conditions with the spring forward angle. Among the processing parameters, the crystallization time at the temperature above 130$^{\circ}C$, was found to be the most effective. Spring-forward angle was reduced and the tensile modulus was increased as the mold temperature increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.73-76
• /
• 2004

High-temperature Superconductor(HTS) tubes were fabricated in term of different processing variables such as preheating temperature, speed of mold rotation and cooling rate by centrifugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050^{\circ}C{\sim}1100^{\circ}C$ and $550^{\circ}C$ for 30min, respectively. The mould roating speed was 1000rpm. A tube was annealed at $840^{\circ}C$ for 72hours in oxygen atmosphere. The plate-like grains were well developed along the roating direction and typical grain size was about more than $40{\mu}m$. It was found that Ic values increased with increasing the preheating temperature and speed of mold rotation. While Ic decreased with increasing the cooling rate. The measured Ic in $50mm{\times}70mm{\times}2.5mm$ tube was about 896Amp.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.7
• /
• pp.67-73
• /
• 2020

Shrinkage is inevitable in the curing of resins during the nanoimprint process. The degree of shrinkage that occurs as the resin transforms from a viscous liquid to solid differs depending on the type of resin. However, if the cured material is repeatedly cured using the same material, constant shrinkage can be confirmed. In this study, the pattern of change was observed by repeatedly performing the nanoimprint process using a resin with a constant shrinkage rate. The observed pattern for the change of shape was made using a triangular pyramid-shaped aluminum master mold and a flexible replica mold made from the master. Shrinkage that results from the nanoimprint process occurs linearly in the longitudinal direction of the pattern and can be predicted by simple calculations. The change of the pattern due to shrinkage occurred as expected. If the shrinkage rate remains constant, various patterns can be manufactured with high accuracy by correcting these changes before producing a specific shape. This study confirms that the pattern of the desired angle can be obtained by performing the repeated imprint without having to manufacture a master mold.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.5
• /
• pp.468-472
• /
• 2005

High-temperature Superconductor(HTS) tubes were fabricated in term of different processing variables such as preheating temperature, speed of mold rotation and cooling rate by centrigugal forming method. For powder melting by induction the optimum range of melting temperatures and preheating temperature were $1050{\circ}C{\sim}1100{\circ}C\;and\;550{\circ}C\;for\;30\; min$, respectively The mould roating speed was 1000 rpm. A tube was annealed at $840 {\circ}C$ for 72 hours in oxygen atmosphere. The plate-like grains were well developed along the loafing direction and typical grain size was about more than $40{\mu}$. It was found that Ic values increased with increasing the Preheating temperature and speed of mold rotation. While Ic decreased with increasing the cooling rate. The measured Ic in $50mm{\times}70mm{\times}2.5mm$ tube was about 896 Amp.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.6
• /
• pp.81-86
• /
• 2017

The high-pressure resin transfer molding (HP-RTM) process has a very effective for the mass production of carbon fiber reinforced plastic (CFRP) for light weight in the automotive industry. In developing robust equipment, new process and fast cure matrix systems reduces significantly the cycle time less than 5 minutes in recent years. This paper describes the cavity pressure, temperature and molding characteristics of the HP-RTM process. The HP-RTM mold was equipped with two cavity pressure sensors and three temperature sensors. The cavity pressure characteristics of the HP-RTM injection, pressurization, and curing processes were studied. This experiment was conducted with selected process parameters such as mold cap size, maximum press force, and injection volume. Consequently, this monitoring method provides correlations between the selected process parameters and final forming characteristics in this work.