• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.1
• /
• pp.34-41
• /
• 2002

In the conventional rake receiver structure for the IS-95 CDMA system, each finger has its own time-deskew buffer or FIFO that aligns the multipath signals to the same timing reference in order to combine symbols. This architecture is not a burden to the rake receiver design mainly because of the small number and size of the buffers. However, the number and size of the buffers are significantly increased in the cdma2000 system which adopts multiple carriers and the small spreading gain for a higher rate in data services. In order to decrease the number of buffers, we propose a new model of the time-deskew buffers, which combines the symbols as well as realigns them at the same time. Our architecture reduces the hardware complexity of the buffers by about more than 60% and 70% compared with the conventional one when we consider each rake receiver has three and four independent fingers, respectively. Moreover, the proposed algorithm is very useful not only to the cdma2000 rake receiver but also to the receiver with many fingers in order to increase the BER performance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.5 s.347
• /
• pp.54-63
• /
• 2006

This work proposes a 14b 100MS/s 0.18um CMOS ADC with optimized resolution, conversion speed, die area, and power dissipation to obtain the performance required in the fourth-generation mobile communication systems. The 3-stage pipeline ADC, whose optimized architecture is analyzed and verified with behavioral model simulations, employs a wide-band low-noise SHA to achieve a 14b level ENOB at the Nyquist input frequency, 3-D fully symmetric layout techniques to minimize capacitor mismatch in two MDACs, and a back-end 6b flash ADC based on open-loop offset sampling and interpolation to obtain 6b accuracy and small chip area at 100MS/s. The prototype ADC implemented in a 0.18um CMOS process shows the measured DNL and INL of maximum 1.03LSB and 5.47LSB, respectively. The ADC demonstrates a maximum SNDR and SFDR of 59dB and 72dB, respectively, and a power consumption of 145mW at 100MS/s and 1.8V. The occupied active die area is $3.4mm^2$.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.149-158
• /
• 2005

This paper describes design, fabrication, and application of the silicon based temperature controllable micro reactor. In order to achieve fast temperature variation and low energy consumption, reaction chamber of the micro reactor was thermally isolated by etching the highly conductive silicon around the reaction chamber. Compared with the model not having thermally isolated structure, the thermally isolated micro reactor showed enhanced thermal performances such as fast temperature variation and low energy consumption. The performance enhancements of the micro reactor due to etched holes were verified by thermal experiment and numerical analysis. Regarding to 42 percents reduction of the thermal mass achieved by the etched holes, approximately 4 times faster thermal variation and 5 times smaller energy consumption were acquired. The total size of the fabricated micro reactor was $37{\times}30{\times}1mm^{3}$. Microchannel and reaction chamber were formed on the silicon substrate. The openings of channel and chamber were covered by the glass substrate. The Pt electrodes for heater and sensor are fabricated on the backside of silicon substrate below the reaction chamber. The dimension of channel cross section was $200{\times}100{\mu}m^{2}$. The volume of reaction chamber was $4{\mu}l$. The temperature of the micro reactor was controlled and measured simultaneously with NI DAQ PCI-MIO-16E-l board and LabVIEW program. Finally, the fabricated micro reactor and the temperature control system were applied to the thermal denaturation and the trypsin digestion of protein. BSA(bovine serum albumin) was chosen for the test sample. It was successfully shown that BSA was successfully denatured at $75^{\circ}C$ for 1 min and digested by trypsin at $37^{\circ}C$ for 10 min.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.2
• /
• pp.35-44
• /
• 2012

Most recent infrared (IR) sensors have a focal-plane array (FPA) structure. Spatial non-uniformity of a FPA structure, however, introduces unwanted fixed pattern noise (FPN) to images. This non-uniformity correction (NUC) of a FPA can be categorized into target-based and scene-based approaches. In a target-based approach, FPN can be separated by using a uniform target such as a black body. Since the detector response randomly drifts along the time axis, however, several scene-based algorithms on the basis of a video sequence have been proposed. Among those algorithms, the state-of-the-art one based on Kalman filter uses one-directional warping for motion compensation and only compensates for offset non-uniformity of IR camera detectors. The system model using one-directional warping cannot correct the boundary region where a new scene is being introduced in the next video frame. Furthermore, offset-only correction approaches may not completely remove the FPN in images if it is considerably affected by gain non-uniformity. Therefore, for FPN reduction in IR videos, we propose a joint correction algorithm of gain and offset based on bi-directional warping. Experiment results using simulated and real IR videos show that the proposed scheme can provide better performance compared with the state-of-the art in FPN reduction.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.49 no.2
• /
• pp.28-34
• /
• 2012

Various feature extraction algorithms are widely applied to real-time image processing applications for extracting significant features from images. Feature extraction algorithms are mostly combined with image processing algorithms mostly for image tracking and recognition. Feature extraction function is used to supply feature information to the other image processing algorithms and it is mainly implemented in a preprocessing stage. Nowadays, image processing applications are faced with embedded system implementation for a real-time processing. In order to satisfy this requirement, it is necessary to reduce execution time so as to improve the performance. Reducing the time for executing a feature extraction function dose not only extend the execution time for the other image processing algorithms, but it also helps satisfy a real-time requirement. This paper explains FAST (Feature from Accelerated Segment Test algorithm) of E. Rosten and presents FPGA-based embedded hardware accelerator architecture. The proposed acceleration scheme can be implemented by using approximately 2,217 Flip Flops, 5,034 LUTs, 2,833 Slices, and 18 Block RAMs in the Xilinx Vertex IV FPGA. In the Modelsim - based simulation result, the proposed hardware accelerator takes 3.06 ms to extract 954 features from a image with $640{\times}480$ pixels and this result shows the cost effectiveness of the propose scheme.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1753-1764
• /
• 2014

Numerical flow simulation models in the riverine environments have been widely utilized for analyzing flow dynamics in various degrees in researches and practical applications. However, most of the simulated results have been validated based on the data from indoor experimental models or very limited in-situ measurements. Therefore, it has been required to more accurately validate the performance of the numerical models in terms of the detailed field observations. In particular, it was also hard to validate the performances of the existing numerical models in the real meandered river channels that encompass more sophisticated flow and geometric structures. Recently, advancements of the modern flow measuring instrumentations such as acoustic Doppler current profilers (ADCPs) enabled us to efficiently acquire the detailed flow field in the broad range of river channels, thus that it became to be possible to accurately validate any numerical models with the field observations. In this study, based on the detailed flow measurements in a actual meandered river channel using ADCP, we validated FaSTMECH model in iRIC in terms of water surface elevation, which is relatively new but began to get highlighted in the research areas. As the validation site, a meandering channel in River Experiment Center of KICT was chosen, which has 6.5 m of width, 0.38m of flow depth, 1.54 m3/s of flow discharge, 0.61 m/s of mean flow velocity, and 1.2 of sinuosity. As results, whereas the FaSTMECH precisely simulated water surface elevation, simulated velocity field in the bend did not match well with ADCP dataset.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.29 no.1
• /
• pp.153-184
• /
• 2018

This study aims to investigate the effects of emotional labor level on the level of job satisfaction and library information service provision in public libraries. The research model used emotional labor levels as an independent variable; job satisfaction and level of library information service provision as a dependent variable; and organizational culture as a control factor. The data were collected randomly from 220 librarians of public libraries in Seoul by distributing and collecting internet surveys. Reliability analysis, correlation coefficient analysis, multiple regression analysis, and regression analysis were performed using the SPSS 18.0 program. The statistic hypothesis test results of this study can be summarized as follows. First, public library librarians did not like to express their emotions to users, trying to express their emotions more positively than what they were actually feeling. Second, although librarians experience emotional labors, they feel a sense of achievement when undertaking their tasks and develop pride and happiness in their work. As librarians perceive their work professional, they overcome emotional labors, and have pride in their work. Third, although librarians experience emotional labors, a reasonable job evaluation with goals, and their relationships with colleagues would lead to accomplishment in their work. In addition, although the evaluation of employees is focused on performance, librarians improve their service if library users are satisfied with their service and the services are provided adequately.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.975-982
• /
• 2005

Scientific community agrees about the fact that base Isolation provides interesting solutions to minimize the seismic risk. Reliability of such a technique is nowadays proofed by a large number of applications like public buildings, nuclear plants, bridges, etc. This paper reports the results of performance verification tests of the base isolated RC building with the laminated rubber bearings which is manufactured by enterprise in Korea. The shaking table tests were performed using a three story model scaled to 1/3 of the prototype RC apartment building. Several major earthquake records were scaled to different peak ground accelerations and used as input base excitations. Especially in this study, effect of earthquake characteristics on response reduction and effect of the intensity of excitations are studied. Through the verification tests, the validity of the applied base isolaion device and the response reduction effect against earthquakes are confirmed.

• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.333-340
• /
• 2012

The current study prepared 9 laboratorial concrete mixes and 3 ready-mixed concrete batches to examine the size and shape effects in compression failure of lightweight aggregate concrete (LWC). The concrete mixes were classified into three groups: normal-weight, all-lightweight and sand-lightweight concrete groups. For each concrete mix, the aspect ratio of circular or square specimens was 1.0 and 2.0. The lateral dimension of specimens varied between 50 and 150 mm for each laboratorial concrete mix, whereas it ranged from 50 to 400 mm with an incremental variation of 50 mm for each ready-mixed concrete batch. Test observations revealed that the crack propagation and width of the localized failure zone developed in lightweight concrete specimens were considerably different than those of normal-weight concrete (NWC). In LWC specimens, the cracks mainly passed through the coarse aggregate particles and the crack distribution performance was very poor. As a result, a stronger size effect was developed in LWC than in NWC. Especially, this trend was more notable in specimens with aspect ratio of 2.0 than in specimens with that of 1.0. The prediction model derived by Kim et al. overestimated the size effect of LWC when lateral dimension of specimen is above 150 mm. On the other hand, the modification factors specified in ASTM and CEB-FIP provisions, which are used to compensate for the shape effect of specimen on compressive strength, were still conservative in LWC.

• Journal of the Korean Data and Information Science Society
• /
• v.22 no.4
• /
• pp.679-690
• /
• 2011

Two widely used approaches for improving the quality of the output of a process are statistical process control (SPC) and automatic process control (APC). In recent hybrid processes that combine aspects of the process and parts industries, process variations due to both the inherent wandering and special causes occur commonly, and thus simultaneous application of APC and SPC schemes is needed to effectively keep such processes close to target. The simultaneous implementation of APC and SPC schemes is called integrated process control (IPC). In the IPC procedure, the output variables are monitored during the process where adjustments are repeatedly done by its controller. For monitoring the APC-controlled process, control charts can be generally applied to the output variable. However, as an alternative, some authors suggested that monitoring the input variable may improve the chance of detection. In this paper, we evaluate the performance of several monitoring statistics, such as the output variable, the input variable, and the difference variable, for efficiently monitoring the APC-controlled process when we assume IMA(1,1) noise model with a minimum mean squared error adjustment policy.