• Journal of electromagnetic engineering and science
• /
• 제12권1호
• /
• pp.101-106
• /
• 2012

In this study, we investigated the effect of groove pattern and gap-fill with lossy materials at 15 GHz frequency of Ku-band. We used Epoxy/MWCNT composite materials as gap-fill materials. Although epoxy does not have an absorbance capability, epoxy added conductive fillers, which are multi-walled carbon nanotubes (MWCNT), can function as radar absorbing material. Specimens were fabricated with different MWCNT mass fractions (0, 0.5, 1.0, 2.0 wt%) and their permittivity in the Ku-band was measured using the waveguide technique. We investigated the effect of gap-fill on monostatic RCS by calculating RCS with and without gap-fill. For arbitrarily chosen thickness and experimentally obtained relative permittivity, we chose the relative permittivity of MWCNT at 2 wt% (${\varepsilon}_r$=8.8-j2.4), which was the lowest reflection coefficient for given thickness of 3.3 mm at V-pol. and $80^{\circ}$ incident angle. We also checked the monostatic RCS and the field intensity inside the groove channel. In the case of H-pol, gap-fill was not affected by the monostatic RCS and magnitude was similar with or without gap-fill. However, in the case of V-pol, gap-fill effectively reduced the monostatic RCS. The field intensity inside the groove channel reveals that different RCS behaviors depend on the wave polarizations.

• The Journal of Korean Physical Therapy
• /
• 제9권1호
• /
• pp.89-96
• /
• 1997

The purpose of this study was to determine the effect of Ga-Al-As (Gallium-Aluminum-Arsenid) laser radiation on the tail-flick latency in rat. Thirty Sprague-Dawley male and female rats Were divided into five groups : that is control, laser 15sec radiation, laser 30sec radiation, laser 60sec radiation, and Tramadol Hcl injection groups. The continuous Ga-Al-As laser with, wave length 780-830nm and diameter of probe in the 3mm, averse output of 100mw radiation was applied to the meridian point(Gv 1 : Governing vessel) of the rats. Tail-flick latency were measured with hot plate at $55^{\circ}C$ : before treatment and immediately, 30 minutes, 1 hour, 2 hours, 24 hours, 24 hours and 48 hours after treatment. The result were as follows ; 1. The tail-flick latency according to time varition, control group was not significance. 2. The tail-flick latency according to time varition, laser 15 sec irradiate rats in post-treared was significance(P<0.05). 3. The tail-flick latency according to time varition, laser 30 sec irradiate rats group was not significance. 4. The tail-flick latency according to time varition, laser 60 sec irradiate rats in post 30 minute was significance(P<0.05). 5. The tail-flick latency according to time varition, Tramadol Hcl injection rats in post-treated (P<0.05), post 30 minute(P<0.05), post 60 minute (P<0.01) and 2 hour(P<0.05) was significance. This study suggest that Ga-Al-As (Gallium-Aluminum-Arsenid) laser applied to meridian point of the rat with 15 sec, 30 sec, and 60 set radiation could induc no analgesic effect, but Tramadol Hcl injection rat is good analgesic effect.

• 한국분말재료학회지
• /
• 제20권5호
• /
• pp.355-358
• /
• 2013

Micro trench structures are applied in gratings, security films, wave guides, and micro fluidics. These micro trench structures have commonly been fabricated by micro electro mechanical system (MEMS) process. However, if the micro trench structures are machined using a diamond tool on large area plate, the resulting process is the most effective manufacturing method for products with high quality surfaces and outstanding optical characteristics. A nonferrous metal has been used as a workpiece; recently, and hybrid materials, including polymer materials, have been applied to mold for display fields. Thus, the machining characteristics of polymer materials should be analyzed. In this study, machining characteristics were compared between nonferrous metals and polymer materials using single crystal diamond (SCD) tools; the use of such materials is increasing in machining applications. The experiment was conducted using a square type diamond tool and a shaper machine tool with cutting depths of 2, 4, 6 and 10 ${\mu}m$ and a cutting speed of 200 mm/s. The machined surfaces, chip, and cutting force were compared through the experiment.

• 한국의료질향상학회지
• /
• 제7권2호
• /
• pp.204-216
• /
• 2000

Background : There has been a concern that the quality of care provided to end-stage renal disease (ESRD) patients in the United States may not be as good as recommended. This paper illustrates a composite measure to assess, the quality of care received by ESRD patients undergoing in-center hemodialysis by incorporating outcomes for 4 major treatment areas. The 4 treatment areas are: dialysis treatments, anemia control, nutritional management, and blood pressure control. Methods : The major data source for the study was the United States Renal Data System (USRDS) Dialysis Morbidity and Mortality Study Wave 1 (DMMS-1) d Sixteen categories of a composite quality indicator were constructed by combining 4 dichotomous variables (16=2*2*2*2). representing the optimal vs. less than optimal level of outcome for each of the 4 treatment outcome measure respectively. Optimal outcome level for each treatment area was defined based on the recommendation from the National Kidney Foundation: (a) delivered dialysis doses (Kt/V) ${\geq}$ 1.2; (b) hematocrit level ${\geq}$ 30%; (c) serum albumin concentration ${\geq}$ 3.8g/dl ; and (d) blood pressure of <140 / <90mmHg. The 16 quality indicator were ranked according to their relative quality weights, which were estimated from its association with the relative risk of survival, adjusting for patient's baseline severity and dialysis facility characteristics. Results : Out of the entire sample of 2,179 patients, only 229 (10%) meet th recommended outcome levels for all 4 treatment areas. Overall, the study patients were distributed evenly over the 16 quality indicators, indicating a great variation in the quality of ESRD care. It appears that the rank of the 16 quality-indicators is driven by serum albumin concentration, suggesting that serum albumin concentration may be the most powerful predictor of ESRD patient survival among the 4 outcome measures. Conclusion : The developed quality indicator has the advantage of describin a range of care for dialysis patients and thus providing a more complete picture of care as compared to previous studies that have focused on only single or few components of the ESRD care.

• Progress in Superconductivity
• /
• 제10권2호
• /
• pp.139-143
• /
• 2009

We have fabricated a low-noise 61-channel axial-type first-order gradiometer system for measuring fetal magnetocardiography(MCG) signals. Superconducting quantum interference device(SQUID) sensor was based on double relaxation oscillation SQUID(DROS) for detecting biomagnetic signal, such as MCG, magnetoencphalogram(MEG) and fetal-MCG. The SQUID sensor detected axial component of fetal MCG signal. The pickup coil of SQUID sensor was wound with 120 ${\mu}m$ NbTi wire on bobbin(20 mm diameter) and was a first-order gradiometer to reject the environment noise. The sensors have low white noise of 3 $fT/Hz^{1/2}$ at 100 Hz on average. The fetal MCG was measured from $24{\sim}36$ weeks fetus in a magnetically shielded room(MSR) with shielding factor of 35 dB at 0.1 Hz and 80 dB at 100 Hz(comparatively mild shielding). The MCG signal contained maternal and fetal MCG. Fetal MCG could be distinguished relatively easily from maternal MCG by using independent component analysis(ICA) filter. In addition, we could observe T peak as well as QRS wave, respectively. It will be useful in detecting fetal cardiac diseases.

• 폴리머
• /
• 제33권5호
• /
• pp.420-428
• /
• 2009

In this study, the composites containing carbon black (CB) or carbon fibers were prepared, and the microwave absorbing properties and the absorption mechanism of them were investigated and discussed in the frequency range of 2-18 GHz, respectively. The optimum mass fraction of CB has been found as 6%, and the carbon fibers were discovered to absorb radar wave either under parallel or vertical polarization, the suitable gap distance between each bundle of which was 5 mm. According to the results of the single constitute absorber samples, the structured composites with the two kinds of absorbers combination were fabricated and studied at 2-18 GHz. The top layer absorbers affect the absorption performance a lot; the maximum reflection loss of composites with CB as top layer absorbers was -31.8 dB with the frequency range of 2.4 GHz below -10 dB, and the other type with CFs as the top layer absorbers obtained the reflection loss peak value of -31.4 dB with 2 GHz below-10 dB.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.561-569
• /
• 2002

Laser has been called a "Quantum Machine" because of its mechanism of generation since the development on July 7,1960.by T.H.Maiman. We can now use this machine as a tool for manufacturing in industries. At present, 45kW CO2 laser, 10kW Nd:YAG laser, 6kW LD pumped YAG laser and 4kW direct diode laser facilities are available for welding a heavy steel plate of 40mm in thickness and for cutting metals at high speed of 140m/min. Laser Materials Processing is no longer a scientific curiosity but a modern tool in industries. Lasers in manufacturing sector are currently used in welding, cutting, drilling, cladding, marking, cleaning, micro-machining and forming. Recently, high power laser diode, 10kW LD pumped YAG laser, 700W fiber laser and excimer laser have been developed in the industrialized countries. As a result of large numbers of research and developments, the modem laser materials processing has been realized and used in all kinds of industries now. In the present paper, metallurgical studies on laser materials processing such as porosity formation, hot cracking and the joint performances of steels and aluminum alloys and dissimilar joint are discussed after the introduction of laser facilities and laser applications in industries such as automotive industry, electronics industry, and steel making industry. The wave towards the use of laser materials processing and its penetration into many industries has started in many countries now. Especially, development of high power/quality diode laser will be accelerate the introduction of this magnificent tool, because of the high efficiency of about 50%, long life time and compact.

• 한국임상수의학회지
• /
• 제31권4호
• /
• pp.325-328
• /
• 2014

A 8-month-old female Maltese dog was presented with a history of heart murmur. In physical examination, grade 4/6 systolic murmur heard at the left heart base. Electrocardiography showed sinus arrhythmia, right axis deviation, deep S wave and splintered QRS complex. Thoracic radiography revealed enlarged right side heart and bulging of the main pulmonary artery. Echocardiography showed mild hypertrophy of right ventricle, a supravalvular stenosis, marked post-stenotic dilation of the main pulmonary artery and a moderately increased pulmonary arterial velocity through the stenotic area (4.4 m/s, pressure gradient of 78.7 mmHg). The dog was diagnosed with supravalvular pulmonic stenosis based on the diagnostic imaging findings. Medical management using ${\beta}1$-blocker and ACE inhibitor was started in this dog and this is first case report described diagnostic characteristic features of supravalvular pulmonic stenosis in korea.

• 전자공학회논문지
• /
• 제50권2호
• /
• pp.104-113
• /
• 2013

60GHz 멀티-기가비트 WPAN 시스템을 위한 고속 QC-LDPC 복호기의 구조를 제안한다. 제안한 QC-LDPC 복호기 설계를 위하여 4 블록-병렬 계층 복호 기술과 fixed wire network 기술이 적용 되었다. 2단 파이프라이닝과 4 블록-병렬 계층 복호기술은 동작 주파수와 데이터 처리량을 개선시키는데에 큰 효과가 있다. 또한 본 제안한 복호기 구조에서 스위치 네트워크를 구현하여 위하여 fixed wire network로 간단하게 구현될 수 있으면 하드웨어 복잡도를 크게 감소시킬 수 있다. 제안한 672-비트, rate-1/2인 QC-LDPC 복호기 구조는 90-nm CMOS 표준 셀을 이용해 설계 및 합성하였다. 성능 분석 결과 제안한 QC-LDPC 복호기 구조는 794K 게이트를 가지며 클락 속도 290MHz 에서 작동한다. 12-iteration일 때 데이터 처리율은 3.9 Gbps 이며 60GHz WPAN 시스템에 적용되어 사용 될 수 있다.

• Journal of Periodontal and Implant Science
• /
• 제33권2호
• /
• pp.139-147
• /
• 2003

The roots of teeth exposed by gingival recession, may be successfully covered by various type of gingival grafting procedures. Vascularization of the recipient site is an essential determinant of the grafts' survival during the first healing stages. It has been suggested that a procedure by which they stimulate the periosteum presurgically will induce the proliferation of neo-endothelium in the site to be operated. The purpose of this study is to evaluate the variations in the gingival blood flow during 4weeks after periosteal stimulation in patient scheduled to receive gingival grafts and to compare variations in the gingival blood flow between smoker and non-smoker. Laser Doppler Flowmetry(floLAB(R), Moor Instruments Ltd, England ; wave length = 780mm. Max. power =l.6mW) was used to measure the gingival blood flow. 112 sites of 68 male patients (32 smokers and 36 non-smoker), aged between 23 and 48 years (smoker : 24-44 years. mean=32.6, non-smoker : 23-48 years, mean=28.5) were monitored for the blood flow. Gingival blood flow measured at before periosteal stimulation, 1-, 2-, 3-, and 4-weeks after periosteal stimulation from 10 a.m. to 2 p.m. The difference of blood flow in each measuring time, each measuring site and between smokers and non-smokers were statistically analyzed by MANOVA. The results were as follows : (1) Blood flow stayed increased for 2 weeks, and then, it was a tendency to decrease(p<0.05). (2) There was no statistically significant difference of blood flow change between smokers and non-smokers. (3)The blood flow at middle site had lower than mesial and distal site during the measuring periods(p<0.05). The present study suggested that blood flow change following periosteal stimulation was significant difference, thus periosteal stimulation before gingival graft might induce favorable results in gingival recession patient.