• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.211-221
• /
• 1994

In this study, to maximize the solar energy utilization for greenhouse heating during the winter season, solar energy-underground latent heat storage system was constructed, and the thermal performance of the system has been analyzed to obtain the basic data for realization of greenhouse solar heating system. The results are summarized as follows. 1. $Na_2SO_4{\cdot}10H_20$ was selected as a latent heat storage material, its physical properties were stabilized and the phase change temperature was controlled at $13{\sim}15^{\circ}C$. 2. Solar radiation of winter season was the lowest value in December, and Jinju area was the highest and the lowest value was shown in Jeju area. 3. The minimum inner air temperature of greenhouse with latent heat storage system(LHSS) was $7.0{\sim}7.5^{\circ}C$ higher than that of greenhouse without LHSS and was $7.0{\sim}11.2^{\circ}C$ higher than the minimum ambient air temperature. 4. Greenhouse heating effect of latent heat storage system was getting higher according to the increase of solar radiation and was not concerned with the variation of minimum ambient air temperature. 5. The relative humidity of greenhouse with latent heat storage system was varied from 50 to 85%, but that of greenhouse without LHSS was varied from 30 to 93%. 6. The heating cost of greenhouse with solar energy-latent heat storage system was about 24% of that with the kerosene heating system.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 동계학술발표대회 논문집
• /
• pp.440-445
• /
• 2008

In this paper, new methodology is proposed to estimate the cooling load using areas of building group and predicted weather data. Only three parameters such as maximum, minimum temperature and building area are necessary to obtain hourly distribution of cooling load for the next day. The maximum and minimum temperature that are used for input parameters can be obtained from forecasted weather data. The areas of building group are used for setting several parameters that are used for estimate cooling loads. Benchmarking building(research building) is selected to validate the performance of the proposed method, and the estimated cooling loads in hourly bases are calculated and compared with the measured data for benchmarking building. The estimated results show fairly good agreement with the measured data for benchmarking building.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.374-377
• /
• 2008

Magnesium alloy sheets are usually formed at temperatures between $150^{\circ}C$and $300^{\circ}C$ because of their poor formability at room temperature. In the present study, the formability of AZ31B magnesium alloy sheets was investigated by the analytical and experimental approaches. First, tensile tests and the limit dome height test were carried out at elevated temperatures to get the mechanical properties and forming limit diagram, respectively. And then deep drawing of cross shaped die was tried to get the minimum corner radius and forming limit at specific temperature. Blank shape, punch velocity, minimum corner radius, fillet size, etc, were determined by finite element analysis physical try-outs. Especially, optimum punch and die temperature were suggested through the temperature-deformation analysis using Pam-stamp.

• 한국기후변화학회지
• /
• 제7권2호
• /
• pp.205-215
• /
• 2016

The relationship between the climate and the number of heat-related patients in South Korea was analysed in this study. The number of the patients was 1,612 during the summer 2011 to 2015 according to the Heat-related Illness (HRI) surveillance system. The coefficient of determination between the number of the patients and the daily maximum temperature was higher than that between the number of them and the other elements: the daily mean/minimum temperature and relative humidity. The thresholds of daily maximum and minimum temperature in metropolitan cities (MC) were higher than those in regions except for MC (RMC). The higher the maximum and minimum temperature became, the more frequently the heat-related illness rate was observed. The regional difference of this rate was that the rate in RMC was higher than that in MC. Prolonged heat wave and tropical night tended to cause more patients, which continued for 20 days and 31 days of maximum values, respectively. On the other hand, the relative humidity was not proportional to the number of the patients which was rather decreasing at over 70% of relative humidity.

• Tribology and Lubricants
• /
• 제21권6호
• /
• pp.249-255
• /
• 2005

In this paper, the friction characteristic of engine bearings has been analyzed in terms of a friction loss power, a minimum film thickness and an oil film pressure. This analysis has been focused on the fuel economy improvement with a low viscosity engine oil such as SAE 0W-40, which is used for a friction loss reduction and increased for a Diesel fuel economy. The friction loss power, the minimum oil film thickness and oil film pressure distribution for plain bearings of a Diesel engine are analyzed using an AVL's EXCITE program with a conventional engine oils of SAE 5W-40 and 10W-40, and a low viscosity engine oil of SAE 0W-40. The computed results indicate that a viscosity of engine oils is closely related to the friction loss power and the decreased minimum film thickness in which is a key parameter of a load carrying capacity of an oil film pressure distribution. When the low viscosity engine oil is supplied to engine bearings, it does not affect to the formation of a minimum oil film thickness. But the friction loss power has been significantly affected by low viscosity engine oil at a low operating temperature of 0. Based on the FEM computed results, the low viscosity engine oil at a low temperature range will be an important factor for an improvement of the fuel economy improvement.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권4호
• /
• pp.331-341
• /
• 2013

In the present work, the effect of the gate-to-drain capacitance ($C_{gd}$) on the noise performance of a symmetric tied-gate $In_{0.52}Al_{0.48}As/In_{0.53}Ga_{0.47}As$ double-gate HEMT is studied using an accurate charge control based approach. An analytical expression for the gate-to-drain capacitance is obtained. In terms of the intrinsic noise sources and the admittance parameters ($Y_{11}$ and $Y_{21}$ which are obtained incorporating the effect of $C_{gd}$), the various noise performance parameters including the Minimum noise figure and the Minimum Noise Temperature are evaluated. The inclusion of gate-to-drain capacitance is observed to cause significant reduction in the Minimum Noise figure and Minimum Noise Temperature especially at low values of drain voltage, thereby, predicting better noise performance for the device.

• 한국가스학회지
• /
• 제16권2호
• /
• pp.45-51
• /
• 2012

최소자연발화온도는 가연성혼합물이 화염이나 스파크 없이 주위로부터 충분한 열에너지를 받아서 스스로 발화하는 최저온도를 말한다. 본 연구에서는 ASTM E659 장치를 이용하여 가연성 혼합물인 n-Pentanol+Ethylbenzene계를 구성하는 순수물질과 혼합물의 최소자연발화온도를 측정하였다. Pentanol과 Ethylbenzene의 측정된 최소자연발화온도는 각 각 $285^{\circ}C$, $475^{\circ}C$ 였다. 그리고 n-Pentanol+Ethylbenzene 계의 예측된 최소자연발화온도는 실험값과 적은 평균절대오차에서 일치하였다.

• 한국수산과학회지
• /
• 제17권3호
• /
• pp.197-205
• /
• 1984

열대산 메기 Clarias batrachus를 새로운 양식어종으로 만들기 위한 기초연구의 하나로 이 종의 성장적수온 및 월동을 위한 성장가능최저수온과 저수온에서의 사치가 시작되는 수온을 찾기 위해 1981년3월부터 1982년 3월까지 체중 $12{\sim}40g$사이의 1년생으로서 $14^{\circ}C$에서 $34^{\circ}C$사이의 수온에서 일련의 실험을 실시하여 다음의 결과를 얻었다. 이 종의 약 12g에서 28g사이의 것의 성장적정수온은 약 $25^{\circ}C$로 나타났고 이 수온에서는 이보다 높거나 낮은 수온에서보다 성장과 사료섭취량, 그리고 사료효율면에서 가장 좋은 결과가 나왔다. 성장최저한계수온은 $18^{\circ}C$로 나타났으며 62일간의 실험에서 1일성장률은 약 $0.1\%$로 낮았으나 폐사는 없었고 활동도 비교적 활발하였다. 따라서 이 종의 월동가능최저수온은 $18^{\circ}C$로 사료된다. $16^{\circ}C$또는 이보다 약간 낮은 수온에서 방치하면 약 30일내에 대부분 폐사하며 $14^{\circ}C$이하에서는 $1{\sim}7$일 내에 모두 폐사하였다. 따라서 이 종에 있어서 폐사가 시작되는 수온은 $16^{\circ}C$로 사료된다. 성장가능최저수온 근처에서 장기간사육할 경우 급작스런 수온하강, 특히 $15^{\circ}C$이하로 내려가는 경우 전체 어류에 치명적인 피해가 예상되므로 주의하지 않으면 안될 것으로 사료된다.

• 설비공학논문집
• /
• 제19권5호
• /
• pp.394-402
• /
• 2007

To estimate the cooling load for the following day, outdoor temperature and humidity are needed in hourly base. But the meteorological administration forecasts only maximum and minimum temperature. New methodology is proposed for predicting hourly outdoor temperature and humidity by using the forecasted maximum and minimum temperature. The correlations for normalized outdoor temperature and specific humidity has been derived from the weather data for five years from 2001 to 2005 at Seoul, Daejeon and Pusan. The correlations for normalized temperature are independent of date, while the correlations for specific humidity are linearly dependent on date. The predicted results show fairly good agreement with the measured data. The prediction program is also developed for hourly outdoor dry bulb temperature, specific humidity, dew point, relative humidity, enthalpy and specific volume.

• 한국전기전자재료학회논문지
• /
• 제14권7호
• /
• pp.572-577
• /
• 2001

The electrical properties of Pr$_{6}$ O$_{11}$ -based ZnO varistors consisting of ZnO-Pr$_{6}$ O$_{11}$ -CoO-Cr$_2$O$_3$-Er$_2$O$_3$ ceramics were investigated with sintering temperature in the range of 1325~f1345$^{\circ}C$. As sintering temperature is raised., the nonlinear exponent was increased up to 1335$^{\circ}C$, reaching a maximum 70.53, whereas raising sintering temperature further caused it to decrease, reaching a minimum 50.18 and the leakage current was in the range of 1.92~4.12 $\mu$A. The best electrical properties was obtained from the varistors sintered at 1335$^{\circ}C$, exhibiting a maximum (70.53) in the nonlinear exponent and a minimum (1.92 $\mu$A) in the leakage current, and a minimum (0.035) in the dissipation factor. On the other hand, the donor concentration was in the range of (0.90~1.14)x10$^{18}$ cm$^{-3}$ , the density of interface states was in the range of (2.69~3.60)x10$^{12}$ cm$^{-2}$ , and the barrier height was in the range of 0.77~1.21 eV with sintering temperature. With raising sintering temperature, the variation of C-V characteristic parameters exhibited a mountain type, reaching maximum at 134$0^{\circ}C$. Conclusively, it was found that the V-I, C-V, and dielectric characteristics of Pr$_{6}$ O$_{11}$ -based ZnO varistors are affected greatly by sintering temperature.