• Korean Journal of Food Science and Technology
• /
• v.18 no.3
• /
• pp.197-203
• /
• 1986

An enzymatic flour milling process for barley into three major fractions (barley flour, bran-crease-germ and water solubles) was studied. Carbohydrate and protein of barley endosperm could be efficiently solubilized by the digestion process of partially pearled barley with enzymes. Bran, crease and germ were removed from hydrolyzate by filtering through 30-40mesh sieves. And then filtered product was separated into fractions by sedimentation or centrifugation. The most effective digestion of the barley was obtained by the enzyme with higher activities of glucanase and protease under such conditions as barley-water ratio, 1:1.5(W/V) and temperature at $45^{\circ}C$. Total flour yield recovered was approximately 73-76% of the barley, and the portions recovered as bran-crease-germ and water solubles were about 3.6 and 15.8%, respectively.

• Korean Journal of Food Science and Technology
• /
• v.29 no.5
• /
• pp.888-894
• /
• 1997

Two hulled and two hull-less barley varieties were investigated for ${\beta}-glucan$ enrichment. Hull-less barleys contained higher levels of total ${\beta}-glucan$ than hulled barleys, and were thus suitable as starting materials for preparing ${\beta}-glucan-rich$ fractions. Particularly, a waxy type (Suweon-291) of hull-less barley was found to have high soluble dietary fiber content containing primarily ${\beta}-glucan$, compared to the other non-waxy barley varieties. ${\beta}-Glucan$ content of barley during pearling process was measured, and the highest value was observed at the pearling yield of approximately $70{\sim}75%$. The pearled barley grains were ground and sieved to yield ${\beta}-Glucan$ enriched fractions containing up to 22% ${\beta}-glucan$. In the meanwhile, whole barley samples were directly milled by $B{\ddot{u}}hler$ mill to produce bran, shorts, break flour and reduction flour. ${\beta}-Glucan$ contents in the bran and shorts from the milled stream were relatively high, and further concentration of ${\beta}-glucan$ could be accomplished by successive sieving of the bran and shorts fractions. Pearled barley and milled stream could be used to prepare barley fractions with ${\beta}-glucan$ concentrations $2.4{\sim}3.1$ times those of the original barley grain. Water solubility of barley ${\beta}-glucan$ from pearled barley and the milled stream was in the range of $40{\sim}81%$.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.373-382
• /
• 1998

Particulate reinforced aluminum alloys produced by indirect squeeze casting are difficult to shape by cutting or milling. Therefore near net shape forming of complex shapes is of high economic and technical interest. The complex shape products of $SiC_p/6061$ Al composites are fabricated by the melt-stirring and indirect squeeze casting process. The mold temperatures are $200^{\circ}C$ and $300^{\circ}C$ and applied pressures are 70, 100, and 130 MPa. The volume fractions of the reinforcements are in the range of 5 vol% to 15 vol%. The reinforcement dispersion state are observed using on optical microscope. By employing observed results systematically a correlation is demonstrated among the microstructure, particles behavior, mechanical properties and processing parameters for an optimum melt-stirring(compocasting) and indirect squeeze casting process of MMCs. A procedure to establish the optimum squeeze casting of Al-MMCs is proposed.

• Journal of Powder Materials
• /
• v.31 no.1
• /
• pp.30-36
• /
• 2024

The aerospace and power generation industries have an increasing demand for high-temperature, high-strength materials. However, conventional materials typically lack sufficient fracture toughness and oxidation resistance at high temperatures. This study aims to enhance the high-temperature properties of Nb-Si-Ti alloys through ball milling. To analyze the effects of milling time, the progression of alloying is evaluated on the basis of XRD patterns and the microstructure of alloy powders. Spark plasma sintering (SPS) is employed to produce compacts, with thermodynamic modeling assisting in predicting phase fractions and sintering temperature ranges. The changes in the microstructure and variation in the mechanical properties due to the adjustment of the sintering temperature provide insights into the influence of Nb solid solution, Nb5Si3, and crystallite size within the compacts. By investigating the changes in the mechanical properties through strengthening mechanisms, such as precipitation strengthening, solid solution strengthening, and crystallite refinement, this study aims to verify the applicability of Nb-Si-Ti alloys in advanced material systems.

• Journal of Powder Materials
• /
• v.9 no.6
• /
• pp.394-408
• /
• 2002

Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.

• Korean Journal of Food Science and Technology
• /
• v.35 no.4
• /
• pp.610-616
• /
• 2003

Five oats and 17 barley cultivars were ground, sieved (105, 210, 300, 425, 600 ${\mu}m$) and we have analyzed the ${\beta}-glucan$ contents to obtain grain fractions. The milling yields ranged $65.1{\sim}89.7%$ for barley and $53.4{\sim}73.5%$ for oat cultivars. Total ${\beta}-glucan$ contents of barley and oats become higher than those of the flour increasing the particle size. The soluble and insoluble ${\beta}-glucan$ contents of them were especially higher in medium and coarse particle size fractions. The contents of total, soluble and insoluble ${\beta}-glucan$ of barley were 1.5, 1.7 and 2.0 times higher than the whole flour before sieving and these content of oats were 2.1, 1.6 and 2.0 times, respectively. In this study, larger particle size would enrich the ${\beta}-glucan$ and it is desirable to consider the best particle size range to enrich the ${\beta}-glucan$ level, the water-solubility of the ${\beta}-glucan$ as well as cereal varieties.

• Korean Journal of Agricultural Science
• /
• v.39 no.3
• /
• pp.387-393
• /
• 2012

In the present study, ${\beta}$-glucanase-assisted extraction of starch from glutinous barley(Hinchal ssalbory) was investigated. ${\beta}$-glucanase was added to a coarse starch suspension obtained after wet milling in the starch extraction process. It was found that in the isolated starch with enzyme treatment, protein content was lower by 0.03%, compared to that with non-enzyme treatment. More importantly it was observed that the extraction yield of starch from enzyme treatment was found to be about 12% higher than the one from non-enzyme treatment (enzyme treated: 90.56%, non-enzyme treated: 78.46%). In order to elucidate this finding, the mass-balance determination of starch in each extraction step was carried out and found that the enzyme treatment might influence on the insoluble residues(R3 and R4 fractions) to hydrolyze ${\beta}$-glucan and other materials (e.g., mucilages etc.), thereby facilitated the separation of starch from it and a next filtration process. With a phase-contrast microscope it was observed that the isolated starch with enzyme treatment contained small starch granules more than the one with non-enzyme treatment and this might result in higher extraction yield observed with the former. In order to confirm this hypothesis, further experiments would be necessary.

• Journal of Powder Materials
• /
• v.28 no.1
• /
• pp.20-24
• /
• 2021

Ti-based alloys are widely used in biomaterials owing to their excellent biocompatibility. In this study, Ti-Mn-Cu alloys are prepared by high-energy ball milling, magnetic pulsed compaction, and pressureless sintering. The microstructure and microhardness of the Ti-Mn-Cu alloys with variation of the Cu addition and compaction pressure are analyzed. The correlation between the composition, compaction pressure, and density is investigated by measuring the green density and sintered density for samples with different compositions, subjected to various compaction pressures. For all compositions, it is confirmed that the green density increases proportionally as the compaction pressure increases, but the sintered density decreases owing to gas formation from the pyrolysis of TiH2 powders and reduction of oxides on the surface of the starting powders during the sintering process. In addition, an increase in the amount of Cu addition changes the volume fractions of the α-Ti and β-Ti phases, and the microstructure of the alloys with different compositions also changes. It is demonstrated that these changes in the phase volume fraction and microstructure are closely related to the mechanical properties of the Ti-Mn-Cu alloys.

• Journal of Food Hygiene and Safety
• /
• v.37 no.6
• /
• pp.418-428
• /
• 2022

The purpose of this study was to obtain the codex classification information on the primary food commodity (fresh state) of processed foods of plant origin that are included in the Codex Classification of Foods and Animal Feeds. Furthermore, whether or not the primary food commodity is included in the primary food classification from the Food Code of Korea was investigated. The results are summarized as follows: First, the Codex Classification information (number of classification codes/number of the primary food commodity group that fresh commodities of processed foods are classified/number of primary food commodity that is not included in the Codex Classification) by a processed food group appeared to be 46/8/0 for dried fruits, 76/11/1 for dried vegetables, 54/4/12 for dried herbs, 36/1/0 for cereal grain milling fractions, 17/4/3 for oils and fats (crude), 34/8/9 for oils and fats (refined), 20/8/0 for fruit juices, 3/2/0 for vegetable juices, and 19 codes for teas (in the Codex Classification, the primary food commodity group for tea does not exist). Second, the number of the primary food commodities not included in the Food Code of Korea was 9 for dried fruits, 14 for dried vegetables, 35 for dried herbs, 0 for cereal grain milling fractions, 6 for teas, 3 for oils and fats (crude), 9 for oils and fats (refined), 2 for fruit juices, and 0 for vegetable juices. Third, it was demonstrated that caution should be exercised when using Codex Classification due to differences in food classification between Codex and Korea, such as coconut (Codex, as tree nut as well as assorted tropical and sub-tropical fruit) and olive (Codex, as assorted tropical and sub-tropical fruit as well as olives for oil production), as well as special cases in the Codex Classification, such as dried chili pepper (Codex, as spice), tomato juice (Codex, as vegetable for primary food commodity and as fruit juice for juice) and ginger (Codex, as spice for rhizome and not including as primary commodity for leaves).

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.2
• /
• pp.129-138
• /
• 2008

The characteristics of beneficiating kaolin mineral by liberation (selective grinding) and air classification have been investigated, comparing the grinding rates of ball mill and impact mill. The ore was ground using a ball mill and a impact mill to evaluate the grindability of the two grinding methods based on the constant production amount of fine particles in size less than 325 mesh. Then, the fine product was further separated into two fractions using an air-classifier and each fraction was chemically analyzed to compare the beneficiation efficiency of the two grinding methods. The chemical grade of kaolin mineral decreased as increasing the grinding rate of both the mills. particularly in the case of ball mill because of overgrinding impurities such as quartz and feldspar. In the case of the ball milling, the fine fraction less than 325 mesh was air-classified at a cutting point of $43\;{\mu}m$. The production rate of the air-classified concentrate was found to be 66.2 wt%, removing 5.3% of $Fe_2O_3$ and 34.6% of CaO. Under the same conditions mentioned above with the impact mill, the production rate of the air-classified concentrate was 64.4 wt%, removing 34.2% of $Fe_2O_3$, 67.6% of CaO and 25.0% of $TiO_2$. Therefore, our results indicate that impact mill is superior to ball mill in terms of impurity removal.