• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.1005-1009
• /
• 2008

A noble infrared $\lambda/4$ absorbing structure using metal reflector was studied for uncooled infrared sensors. This paper described the design and the fabrication of IR uncooled detectors which were composed of 21 by 21 elements using the surface micromachining technology. The characteristics of the array were investigated in the spectral region of 4.26 ${\mu}m$. The fabricated detectors exhibited the thermal mass of $9.75\times10^{-9}$ J/K, the thermal conductance of $1.31\times10^{-6}$ W/K, the thermal time constant of 7.4 ms, the responsivity of $1.07\times10^5$ V/W and the detectivity of $1.04\times10^9$ $cmHz^{1/2}/W$, at the chopper frequency of 10 Hz and the bias current of 9.22${\mu}A$. Finally the absorptance efficiency of $\lambda/4$ absorbing structure was about 23.2 % higher than that of absence absorbing structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.7
• /
• pp.1001-1006
• /
• 2012

This paper presents a carbon nanotube (CNT) triode-structure field emitter as an ion source in a micro time-of-flight mass spectrometer(TOF-MS). In the ion source by field emission, the electrons emitted from cathodes under an electric field accelerated to the anode and ionize gas molecules by impact before arriving the anode. The generated positive ions are to be accelerated to the ion collector. Whereas most of ions are drawn to the cathodes in diode field emitters, a grid in the triode field emitter prevents the ions from being drawn to the cathodes. The triode field emitter is fabricated by micromachining. The cathode is composed of six CNT cylinders. The total size of the fabricated device is $8.0{\times}7.3{\times}1.9mm^3$. The anode and the grid current of the fabricated CNT field emitter were measured for various anode and grid voltages. When the anode and the grid voltages are 1000 V and 990 V, respectively, the emission current passing through the ionization region is 8.6 ${\mu}A$, which is a sufficient emission current for ionization and mass spectrometry.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1524-1525
• /
• 2007

A flexible tactile sensor module based on polyimide matrix integrated with sensing elements and pluggable terminals connector was fabricated by polymer micromachining technology for robotic applications. The tactile sensor arrays are composed of $4{\times}4$, $8{\times}8$ and $16{\times}16$ sensing elements connected with pluggable terminals connector, respectively. Especially, both the tactile sensor array and the pluggable terminals are formed in the sensor module during the fabrication process. The fabricated tactile sensor module is measured continuously in the normal force range of $0{\sim}1N$ with tactile sensor auto-evaluation system. The value of resistance is relatively increased linearly with normal force in the overall range. The variation rate of resistance is about 2.0%/N in the range of $0{\sim}0.6N$ and 1.5%/N in the range of $0.6{\sim}1N$. Also, the flexibility of the sensing module is adequate to be placed on any curved surface as cylinder because the matrix consists of polymer and metal thin film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.352-353
• /
• 2006

가스센서용 마이크로 히터 제작에는 표연 마이크로 머시닝 또는 벌크 마이크로머시닝 기술을 이용한다. 표면 마이크로 머시닝에 의한 마이크로 히터 (MHP) 구조의 경우, 기판과 박막간의 폭이 좁기 때문에 에칭 공정 후 세정이 잘 이루어지지 않으면 열적 절연이 잘 이루어지지 않아서 히터와 센서의 성능을 저하시키는 원인이 된다. 본 연구에서는 표면 마이크로 머시닝 기술에 의한 가스 센서용 마이크로 히터를 제작한다. $SiO_2$와 $Si_3N_4$를 성분으로 하며, $100{\mu}m\;{\times}\;100{\mu}m$의 면적과 350 nm 의 두께를 갖는 가스 센서용 마이크로 히터를 제작하였다. 이를 위하여 ANSYS를 통한 유한요소해석에 의한 열분포 해석으로 최적구조를 확인하였다. 센서로의 열 전달 효율을 높이기 위해 센서 박막은 히터 위에 적층하였다. 실리콘 표면과 마이크로 히터와의 간격은 에칭 공정을 통하여 $2{\mu}m$로 하였으며, 이 공간에서는 에칭 및 세정 후에 이물질이 깨끗이 세정되지 않고 남아 있거나, 습식 공정 중에 수분의 장력에 의한 열전연성이 나빠질 수 있는 등 단점이 있다. 이는 건식 등방성 에칭 공정을 통하여 해결하였다.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.53-57
• /
• 2014

We describe the preparation of highly-ordered etching pits on the Nb foil through a micromachining. The effects of electrochemical polishing on the formation of uniformly-patterned protective epoxy layer was investigated. Unlike the previous process using $O_2$ plasma, well-ordered etched pits were prepared without any dry processes. As a result, the Nb foil with the well-ordered pits of $10{\mu}m{\times}5{\mu}m$ could be obtained by electrochemical etching in methanolic electrolytes for 10 min.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.4
• /
• pp.155-160
• /
• 2019

Diamond Like Carbon (DLC) is a metastable form of amorphous carbon that have superior material properties such as high mechanical hardness, chemical inertness, abrasion resistance, and biocompatibility. Furthermore, its material properties can be tuned by additional doping such as nitrogen or boron. However, either pure DLC or doped DLC show poor adhesion property that makes it difficult to apply contact processing technique. Therefore we propose ultrafast laser micromachining which is non-contact precision process without mechanical degradation. In this study, we developed precision machining process of DLC thin film using an ultrafast laser by investigating the process window in terms of laser fluence and laser wavelength. We have also demonstrated various patterns on the film without generating any microcracks and debris.

• Journal of Sensor Science and Technology
• /
• v.9 no.3
• /
• pp.224-232
• /
• 2000

Aluminum metal process in surface micromachining enables to fabricate Al electrodes or Al structures, which improve electrical characteristics by reducing contact- and line-resistance or makes the whole process to be simple by using oxide as sacrificial layer. However, it is not possible to use conventional sacrificial layer etching process, because HF solution attacks aluminum as well as sacrificial oxide. The mixed solution of BHF and glycerine as an alternative shows the adequate properties to meet with this end. The exact etching properties, however, are sensitively depends on the geometry of the released structure, because the most etching process of sacrificial layer proceeds to the lateral direction in narrow space. Also, the surface roughness of aluminum affects to the etching characteristics. This paper reports experimental results on the effect of microstructure and surface roughness of aluminum to the etching properties. Considering these effects, we propose the optimized etching condition, which can be used practically for the fabrication of aluminum electrodes and microstructures by using standard surface micromachining process without modification or additional process.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.4
• /
• pp.347-353
• /
• 2002

A structure of a glass electrode-type pH sensor for measuring any concentration of $H^+$ in an aqueous solution was embodied with bulk micromachining technology. Two open well structures were formed, and a reference electrode was secured by the Ag/AgCl thin film in the sloped side of the etched structure. A sensitive membrane of an indicator electrode for generating a potential by an exchange reaction to $H^+$ was made with a glass containing Na 20% or more finely so that its thickness might be $100{\mu}m$ or so, and then it was bonded to one pyramidal structure. A liquid junction for a current path was formed by filling an agar in the anisotropically etched part of the Si wafer, which had a size of $50{\mu}m{\times}50{\mu}m$, and then bonded it to the other. After complete fabrication of each part, it was filled with a 2M KCl reference solution and encapsulated the sensor structure with a cold expoxy. The potential value of fabricated pH sensor was about 90mV/pH in the standard pH solutions.

• Journal of Biomedical Engineering Research
• /
• v.44 no.6
• /
• pp.404-413
• /
• 2023

In this research, we studied the development of a SUS304 microneedle array based on microfabrication technology and the applicability of Parylene-C thin film, a medical polymer material. First of all, four materials commonly used in the field of medical engineering (SUS304, Ti, PMMA, and PEEK) were selected and a 5 ㎛ Parylene-C thin film was deposited. The applicability of Parylene-C coating to each material was confirmed through SEM analysis, contact angle measurement, surface roughness(Ra) measurement, and adhesion test according to ASTM standards for each specimen. Parylene-C thin film was deposited based on chemical vapor deposition (CVD), and a 5 ㎛ Parylene-C deposition process was established through trial and error. Through characteristic experiments to confirm the applicability of Parylene-C, SUS304 material, which is the easiest to apply Parylene-C coating without pretreatment was selected to develop a microneedle array based on CNC micromachining technology. The CNC micromachining process was divided into a total of 5 steps, and a microneedle array consisting of 19 needles with an inner diameter of 200 ㎛, an outer diameter of 400 ㎛, and a height of 1.4 mm was designed and manufactured. Finally, a 5 ㎛ Parylene-C coated microneedle array was developed, which presented future research directions in the field of microneedle-based drug delivery systems.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.150-150
• /
• 2003