• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.8
• /
• pp.737-743
• /
• 2004

A fixed-tuned SIS(Superconductor-Insulator-Superconductor) mixer across 120∼180 GHz band has been developed. This mixer employs an SIS chip fabricated by Nobeyama radio observatory which consists of a series array of 6 Nb/Al-Al$_2$O$_3$/Nb junctions in a microstrip line on a fused quartz substrate. The SIS chip is placed at the center of the half-height waveguide mixer mount to have a good incoming signal coupling over the whole frequency band. No mechanical tuner was used in the SIS mixer and the RF signal and local oscillator power are injected to the mixer via a cooled cross-guide coupler. In order to prevent the IF signal loss, the If output impedance of the SIS mixer was matched to the 50 $\Omega$ input impedance of the IF chain. Measured double sideband noise temperatures of a receiver using the SIS mixer are 32∼131 K over 120∼180 GHz band. The developed SIS mixer is now in use for radio astronomical observations on the TRAO 14 m radio telescope.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.5 s.236
• /
• pp.707-715
• /
• 2005

In this work, Scalar Passive code in Lattice Boltzmann Method is employed to simulate two-phase flow of low Reynolds number in a micro-channel. The mixing characteristics in a micro-channel is a function of Peclet number. The mixing length increases with the Peclet number. It is found that with the inclusion of static elements at the channel, rapid mixing of two liquids can be achieved, as shown by the results of computer simulations. The enhancement in mixing performance is thought to be caused by the generation of eddies and by lateral velocity component when the mixture flows past static elements. The results indicate that the size of static element has more effect on the mixing than the number of static element.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.378-384
• /
• 2012

Higher compression ratio is required in diesel engine to ignite the fuel that leads to better efficiency. For complete combustion inside the cylinder it is important to ensure the clean air flow with free of debris and as cool as possible. In this manner, modification of intake valve arrangements is taken in to consideration importantly. In this paper, the intake valve arrangements are modified with newly designed valve mixer. It causes swirl flow of air through the intake port that mixing with the fuel followed by complete combustion. The use of valve mixer reduces the carbon sediment formation on valve fillet and its face area as the carbon particles gradually take place on it after certain running period. It therefore, helps to increase the valve lifetime. And at the same time it reduces the exhaust elements i.e. soot from the automobiles to a significant level.

• Journal of Mechanical Science and Technology
• /
• v.18 no.3
• /
• pp.526-532
• /
• 2004

A motionless mixer consists of a straight pipe or transfer tube containing the mixing elements that are used to cut, fold, twist, and re-combine the mixing fluid. The number of elements and their shape required in any application depend on the complexity of the mixing process. The objectives of this study are to develop new motionless mixers and to perform the experimental investigation of pressure drop in order to evaluate the performance of the new ones. Glycerin is used as a mixing fluid. Pressure drop is measured using a hydraulic manometer and correlations of friction factor are proposed as a function of Re. The friction factors of Sulzer SMX mixer are in qualitative good agreement with the published data. On the average, the friction factors of SSC and YNU mixers are about 36% lower than and 6% higher than that of the Sulzer one.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.4
• /
• pp.1-7
• /
• 2003

In this study, fiber mechanical pretreatment before refining was executed with the addition of papermaking addiditives to find synergistic effects on fiber property improvement. Three fiber furnishes (SwBKP, KOCC, and BCTMP), and five different additives (CMC, CPAM, PEO, NaOH, $Na_2O_2$) were used. It was confirmed again that fiber mechanical pretreatment using Hobart mixer was a special way to modify fiber properties, where fiber WRV (water retention value) increases without losing fiber length. For SwBKP, addition of small amount of CMC (0.2％ OD basis), and for KOCC, PEO (0.2％ OD basis) caused additional significant improvement of the fiber furnish properties, respectively. Other additives did not cause adverse effects on the mechanical pretreatment, or better. For BCTMP, NaOH addition followed by mechanical pretreatment caused more than 20％ improvement in tensile and tear strength simultaneously, compared to the control. The yellowing caused by the treatment of NaOH on BCTMP could be minimized by using $Na_2O_2$ without losing the positive effect of NaOH.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.12
• /
• pp.1549-1556
• /
• 2004

We have deigned, fabricated and compared four different types of static chaos microfluid mixers, including the mixers using straight channel flow, microblock-induced alternating whirl flow, microchannel-induced lamination flow, and combined alternating whirl-lamination flow. Among them, the alternating whirl-lamination (AWL-type) mixer, composed of 3-D rotationally arranged microblocks and dividing microchannels fabricated by conventional planar lithography process, is effective to reduce the mixing length over wide flow rate ranges. We characterize the performance of the fabricated mixers, through the flow visualization technique using phenolphthalein solution. We verify that the AWL-type microfluid mixer shows the shortest fluid mixing length of 2.8mm∼5.8mm for the flow rate range of Re=0.26∼26 with the pressure drop lower than 5kPa. Compared to the previous mixers, requiring the mixing lengths of 7∼17mm, the AWL-type microfluid mixer results in the 60% reduction of the mixing lengths. Due to the reduced mixing lengths within reasonable pressure drop ranges, the present micromixers have potentials for use in the miniaturized Micro-Total-Analysis-Systems($\mu$TAS).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.83-89
• /
• 2011

Diesel engines can produce higher fuel efficiency and lower $CO_2$ emission, they are subject to ever more stringent emission regulation. However, there are two major emission concerns fo diesel engines like such as particulate matter (PM) and nitrogen oxides (NOx). Moreover, it is not easy to satisfy the regulations on the emission of NOx and PM, which are getting more strengthened. One of the solutions is to apply the new combustion concept using multistage injection such as HCCI and PCCI. The other solution is to apply after-treatment systems. For example, lean NOx trap catalyst, Urea-SCR and others have various advantages and disadvantages Especially, Urea-SCR system have advantages such as a high conversion efficiency and a wide operation conditions. Hence the key factor to implementation of Urea-SCR technology, good mixing of urea(Ammonia) and gas, reducing Ammonia slip. Urea mixer components are required to facilitate evaporation and mixing because the liquid state of urea poses significant barriers for evaporation, and the distance to mixer is the most critical that affect mixer performance. In this study, to find out the distance from injector to mixer and simulation factor, a laser diagnostics and high speed camera are used to analyze urea injector spray characteristics and to present a distribution of urea solution in transparent manifold In addition, Droplet Uniformity Index is calculated from the acquired images by using image processing method to clarify the distribution of spray.

• 한국가시화정보학회:학술대회논문집
• /
• 2007.11a
• /
• pp.63-65
• /
• 2007

The paper reports on a new type of combinatorial chaotic and serpentine micromixer. Such a new and novel micromixer is simple to fabricate and easy to use. The micromixer is characterized and visualized with the help of the Micro-LIF technique. The new micromixer will e further applied to lab-on-chip device. The mixing capabilities of this mixer is about 30-33%.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.777-782
• /
• 2001

In this study, we used In-line orifice mixer for efficient chemicals mixing in water treatment. The method of using In-line orifice mixer has been already proved the improvement of water treatment efficiency. Numerical study was performed using FLUENT, a commercial code, to standard design and production of effective In-line orifice mixer. As variable for exactly standardizing, a proper ratio between an outer diameter of cone and a diameter of pipe, a distance between cone and orifice, a determination of orifice diameter for an optimal mixing, a distance between injection nozzle's position and cone, Numerical study has been performed for optimal standard and analyzed flow field on a basis of turbulent intensity in an orifice downstream.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1957-1962
• /
• 2004

The objective of this study is to perform the numerical investigation of flow characteristics in static mixers. Simulations are carried out for mixers consisting of up to six Kenics and PPM elements placed end-to-end at an angle of $90^{\circ}$and for a range of Reynolds number($1{\leq}Re{\leq}100$). The pressure drop across a six-element Kenics mixer is computed and compared with the previous experimental correlations. The results are in good agreement with the previous correlations. The simulated flow field of Kenics mixer is extremely complex and contains regions of transverse flow that is dominated by the interaction of vortices produced by the mixer elements.