• Restorative Dentistry and Endodontics
• /
• v.18 no.2
• /
• pp.507-513
• /
• 1993

The purpose of this study was to observe the effect of immersion in water at 3, 5, 7, and 10 minutes after mixing on the surface of three regular and one light-curing glass-ionomer cement by measuring penetration of a methylene blue solution. Early solubility of these cements was also measured and compared with that of a zinc phosphate and a polycarboxylate cement. A blue-stained zone was observed in all glass-ionomer cement, but an inner, opaque zone was observed in only two of the regular glass-ionomer cements. Extending the time between start of mixing and immersion on water decreased the width of both zones in all cements and markedly lowered the loss of substance from the surface of regular glass-ionomer cements. However, time after mixing had no or only a limited effect on the loss of substance from the light-curing glass-ionomer cement, the zine phosphate cement, or the polycarboxylate cement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.695-704
• /
• 2016

Rubber deposited during aircraft landing is known as the main cause of reducing surface friction force on wet surfaces. Thus, rubber deposits are removed at regular intervals for sae airplane landing. The high-pressure waterblast method, widely used for the removal of rubber deposits, is regarded as the main cause for the loss of surface material because in this method, water hits the surface directly at a high pressure. In this study, a rubber removal primer is developed to reduce surface damage by lowering the pressure of waterblast relatively during the removal of rubber deposits such that the deposits are removed efficiently even with a lower water pressure. To achieve this, basic materials appropriate for the primer were selected and their performance, penetration rate, and site applicability were evaluated. Based on the evaluations, the proportion of additive required for improving the performance of the basic materials was first determined. Then, the optimum mix ratio was derived through the evaluation of the effect on pavements, and the development of the rubber removal primer was completed.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.47 no.1
• /
• pp.49-56
• /
• 2021

In this study, a liquid crystal emulsion with a composition ratio similar to the skin lipid composition was manufactured using ceramide, glycolipids, cholesterol, and fatty acids, and a polarized microscope was used to identify liquid crystal particles in the formulation, and a cryso-SEM was used to confirm the formation of a multilayer structure. The above samples were stored at room temperature for one month and the liquid crystal structure was continuously maintained through microscopic observation. In addition, a cream composition containing liquid crystal emulsion was manufactured, and the efficiency of ceramide skin penetration was confirmed using three-dimensional artificial skin. Clinical trials were conducted using the cream composition and the results of clinical trials on skin barrier improvement were confirmed by measuring skin moisture retention (skin hydration) and transepidermal water loss (T EWL) of subjects compared to general emulsion.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.4
• /
• pp.169-177
• /
• 2018

Glass fiber reinforced polyester (GFRP) composites are widely used as structural materials in harsh environment such as underground pipes, tanks and boat hulls, which requires long-term water resistance. Especially, these materials might be damaged due to delamination between gelcoat and composites through an osmotic process when they are immersed in water. In this study, GFRP laminates were prepared by surface treatment of UPE (unsaturated polyester) gelcoat by vacuum infusion process to improve the durability of composite materials used in underground pipes. The composite surface coated with gelcoat was examined for surface defects, cracking, and hardness change characteristics in water-immersion environments (different temperatures of $60^{\circ}C$, $75^{\circ}C$, and $85^{\circ}C$). The penetration depth of cracks was investigated by micro CT imaging according to water immersion temperature. It was confirmed that cracks developed into the composites material at $75^{\circ}C$ and $85^{\circ}C$ causing loss of durability of the materials. The point at which the initial crack initiated was defined as the failure time and the life expectancy at $23^{\circ}C$ was measured using the Arrhenius equation. The results from this study is expected to be applied to reliability evaluation of various industrial fields where gelcoat is applied such as civil engineering, construction, and marine industry.

• Fire Science and Engineering
• /
• v.29 no.4
• /
• pp.67-72
• /
• 2015

A series of fire tests was conducted to examine the fire characteristics of flaming and smoldering combustion of engineered wood products, which have been widely used for furniture and finishing materials in buildings. The engineered wood products of MDF, plywood, and chipboard were ignited by a radiant cone heater with incident heat flux of $50kW/m^2$. During the fire test, key parameters representing the fire characteristics such as the heat release rate, yield rate of combustion product, and effective heat of combustion were quantified in terms of thickness. The tests show two peak points of HRRPUA due to lateral fire propagation in the initial stage, followed by later fire penetration through the specimen thickness. The mass loss rate of flaming combustion was 5 times higher than that of smoldering combustion, while the CO yield rate of smoldering combustion was 10 times higher than that of flaming combustion. This study can contribute to the understanding of fire behavior of wood combustibles and provide useful data for fire analysis.

• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Geomechanics and Engineering
• /
• v.36 no.3
• /
• pp.231-245
• /
• 2024

In recent decades, the protection and vulnerability of civil structures under explosion loads became a critical issue in terms of security, which may cause loss of lives and structural damage. Concrete retaining walls also restrict soils and slopes from displacements; meanwhile, intensive temporary loading may cause massive damage. In the current study, the modified Johnson-Holmquist (also known as J-H2) material model is implemented for concrete materials to model damages into the ABAQUS through user-subroutines to predict the blasting-induced concrete damages and volume strains. For this purpose, a 3D finite-element model of the concrete retaining wall was conducted in coupled Eulerian-Lagrangian simulation. Subsequently, a blast load equal to 500 kg of TNT was considered in three different positions due to UFC 3-340-02. Influences of the critical parameters in smooth blastings, such as distance from a free face, position, and effective blasting time, on concrete damage rate and destroy patterns, are explored. According to the simulation results, the concrete penetration pattern at the same distance is significantly influenced by the density of the progress environment. The result reveals that the progress of waves and the intensity of damages in free-air blasting is entirely different from those that progress in a dense surrounding atmosphere such as soil. Half-damaged elements in air blasts are more than those of embedded explosions, but dense environments such as soil impose much more pressure in a limited zone and cause more destruction in retaining walls.

• Journal of Sericultural and Entomological Science
• /
• v.51 no.2
• /
• pp.142-146
• /
• 2013

The fluorescent proteins are generally denatured by heat treatment and thus lose their color. The normal reeling method includes processing by drying and cooking the cocoons near $100^{\circ}C$ before reeling. Therefore, the usual processing method cannot be used for making colored fluorescent silks. To develop a method that is applicable to producing transgenic silk without color loss, we develop reeling methods adequate for a recombinant fluorescence cocoons. It was found that the fluorescence cocoons keep their native color when dried at temperatures lower than $60^{\circ}C$ for 15 h. Also, a new cooking method to soften the fluorescent cocoons was developed: the cocoons were soaked in a solution of 0.2% sodium carbonate ($Na_2CO_3$)/0.1% nonionic surfactant (Triton X100) at $60^{\circ}C$ and then placed under vacuum. The repeated vacuum treatments enabled complete penetration of the solution into the cocoons, and the cocoons were thus homogenously softened and ready for reeling. In this state, the cooked cocoons can be reeled by an automated reeling machine. Our results suggest that drying and cooking of the cocoons at low temperature enables the subsequent reeling of the colored fluorescent silks by an automatic reeling machine without color loss and can produce silks that can be used for making higher value-added silk materials.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.2
• /
• pp.280-289
• /
• 2013

Various vehicles have been studied in order to protect skin ageing and sustain constantly moisturization. Recently, in relation to maintain of moisture, absorption and penetration of active materials, there has been introducing many preparing methods such as liposome, liquid crystal and multilamellar emulsion. We developed multilayer lamellar vesicle using cetearyl alcohol/ceteth-20 phosphate/dicetyl phosphate as analogy of phospholipid according to variation of shear rate and pH. These multilayer lamellar vesicles were confirmed by cross polarizing microscope. As results, morphologies of lamellar vesicle were not uniformed at low shear rate and pH. Also, stabilities for encapsulation of retinol were observed at $42^{\circ}C$ during two months. As a result, quantitative content of retinol decreased at low pH. Multilayer lamellar vesicle decreased 14% of transepidermal water loss compared with O/W emulsion. We compared multilayer lamellar sun cream to O/W sun cream using in vitro SPF test of water resistance and concluded that multilayer lamellar sun cream is similar to O/W sun cream in water resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.27-33
• /
• 2016

Military textiles with breathable waterproof materials are expanding as form of winter clothes. Waterproof moisture-permeable clothes are very important for soldiers to survive in cold weather operations because they prevent loss of body heat from the penetration of water into the human body. Korea military uses the water resistance and moisture permeability to test the performance of waterproof moisture-permeable materials. Moisture permeability is measured according to the amount of evaporated water vapor passing through a fabric under specified temperature and humidity by using acetic acid potassium presented in KS K 0594. However, the test procedure for measuring the moisture permeability in the standard is presented only briefly and the preparation procedures for the test in accredited testing institutions are applied differently, leading to significant deviation of the results. This paper compares the procedures of testing institutions and examines the factors that affect moisture permeability. Finally, we propose a procedure to reduce the deviation of results and apply the proposed procedure in testing institutions. Our analysis results with one-way ANOVA under significant level (0.05) confirm that the deviation of results is reduced.