• Journal of Magnetics
• /
• 제15권4호
• /
• pp.173-178
• /
• 2010

A new kind of magnetic rubber, Fe dispersed ethylene propylene monomer (EPM), was prepared by a conventional technique using a two roll mill. The magnetic fillers of Fe-nanoparicles were coated by low density polyethylene (LDPE). The purpose of surface treatment of nanoparticles by LDPE is to enhance wettability and lubricancy of the fillers in a polymer matrix. The mechanical strength and microstructure of the magnetic rubber were characterized by tensile strength test and scanning electron microscopy (SEM). Results revealed that the Fe nanoparticles were relatively well dispersed in an EPM matrix. It was found that the nano- Fe dispersed magnetic rubber showed higher coercivity and tensile strength than those of micron- Fe dispersed one.

• 한국자기학회지
• /
• 제24권1호
• /
• pp.22-27
• /
• 2014

자북을 지시하는 방위각 측정용 센서는 항공기와 선박이나 스마트폰 등에 널리 사용되고 있다. 센서의 좌표계가 회전을 하였을 경우도 방위각(azimuth angle) 및 회전각(roll angle)를 지시할 수 있게 하기위하여 3-축의 가속도 센서가 추가로 사용된다. 본 연구에서는 방위각센서에 부착된 3-축의 자기장센서의 특성을 측정하거나, 방위각센서용 3-축의 자기장센서를 개발하기 위하여 3-축의 자기장센서의 방위각 특성을 측정할 수 있는 장치를 개발 제작하였다. 3-축의 자기장발생을 위해서 직경이 290 mm 이상인 3-축의 헬름홀쯔 코일을 사용하여 코일 중심 ${\pm}30mm$ 범위에서 자기장의 분포의 균일도가 0.2 % 이내가 되게 하였다. 비자성실험실이 아닌 일반실험실에서도 실험이 가능하게 소형의 헬름홀쯔 코일과 3-축의 마그네토미터를 사용, 환경자기장(지구자기장+건축물에 의한 자기장)을 보상하고 시험하고자하는 자기장을 컴퓨터 소프트웨어로 제어를 할 수 있게 시험 장치를 고안하였다. 제작된 장치는 자기장을 0.2 % 정확도로, 직각도를 $0.2^{\circ}$, 환경자기장을 10 nT 이하로 보상할 수 있었다. 또한 제작된 장치의 성능검증을 위하여 상용의 방위각센서에 대하여, 그 특성을 측정하여보았다.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.871-878
• /
• 2003

With the development of micro -technology, the demand for micro actual ing device is increasing. But, it is difficult to achieve high resolution and wide bandwidth with the conventional contact systems. So, the contact-free systems which are suspended or levitated by magnetic force or air bearing were proposed. These systems can be applied to high precision stages and alignment apparatuses. This paper describes a magnetically suspended system with four degrees of freedom which are composed of three rotations (roll, pitch, yaw), and one translation ( z). The operating principle and the structure of the system are similar to variable reluctance type electric machines. In this study, the force analysis is executed using magnetic circuit and virtual work principle, and the equations that describe the dynamics of the system are presented. The multivariable PID controller is adapted to the system and the experiment is executed.

• 한국분말재료학회지
• /
• 제3권1호
• /
• pp.13-24
• /
• 1996

Two grades of Permalloy strips, Fe-45Ni(PB) and Fe-78Ni-4Mo-5Cu(PC) were fabricated by powder rolling process from elemental powder mixtures. The roll compacted green strips were sintered, homogenized, cold rolled with or without an intermediate annealing and finally heat treated to measure magnetic properties. For a given thickness reduction, rolling with an intermediate annealing was found more effective to achieve a full densification with no visible micropores and also to obtain better magnetic properties. Increasing the final rolling reduction also produced a marked improvement of the magnetic properties whereas the cooling rate during the final heat treatment has little effect in both grades. Addition of a small amount, 0.4% Mn slightly degraded the properties. As an overall, The PM strips produced via powder rolling yielded the similar soft magnetic properties to the corresponding commercial grades produced via wrought processing.

• 반도체디스플레이기술학회지
• /
• 제11권2호
• /
• pp.1-6
• /
• 2012

In this study, a high performance rotary magnet type magnetron source for roll-to-roll sputter system has been developed. We analyzed the density of magnetic field as a function of size variation of the magnet which are in the center and edge of the target. The target efficiency showed the best result when the width of center magnet, the width of edge magnet, the angle of edge magnet, and the rotation angle of Yoke are 20mm, 10mm, $56^{\circ}$, and $16^{\circ}$, respectively. On the basis of the results of magnet array, Roll-to Roll magnetron source was fabricated and tested. The uniformity of the film thickness and that of the sheet resistance was ${\pm}1.62%$ and ${\pm}4.13%$, and the resistivity was $2.79{\times}10^{-3}W{\cdot}cm$.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 somma/kms meeting
• /
• pp.362-362
• /
• 2003

• 대한기계학회논문집A
• /
• 제40권7호
• /
• pp.659-666
• /
• 2016

자기교란은 관성/자기센서를 이용한 자세추정시 추정정확도를 저하시키는 주된 원인이다. 본 논문은 저자가 개발한 6축 관성센서를 이용한 센서가속도 추정용 칼만필터의 확장으로서, 9축 관성/자기센서를 이용하여 운동체의 자세가 지속적으로 변화하는 가운데 운동체 주변 자기교란을 정확히 추정하고, 이를 통해 자기교란환경에서도 정확한 3차원 자세를 추정할 수 있는 병렬 칼만필터를 제안한다. 제안하는 필터는 자기교란벡터를 상태변수로 지정하여 명시적으로 추정하며, 병렬구조이므로 설령 극심한 자기교란에 의해 자세추정이 영향을 받더라도 롤과 피치와는 무관하고 요에만 영향이 국한되는 장점을 지닌다. 제안방법은 로봇이나 선박, 항공기처럼 자기적으로 균등하지 않은 환경에서 운용되는 분야에 효과적으로 적용될 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.73-76
• /
• 1999

In this thesis, we fabricate a zero-magnetostrictive amorphous ribbon measure the impeadance effect, and then Investigate possibility as a sensor material. $Co_{72.5}$F $e_{0.5}$M $o_{2}$ $B_{15}$ S $i_{5}$ is used as composition of specimen alloy. We first melt the specimen in high frequency induction furnace and then rapidly quench it by using single roll technique. As the result, we obtain a ribbon where thickness is 12${\mu}{\textrm}{m}$, width is 1mm and length is 93mm. Consequently, it is proved through this study that zero-magnetostrictive amorphous ribbon can be used as an excellent magnetic sensor material.rial.l.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.519-523
• /
• 2009

This paper presents the analysis of pitch static attitude (PSA) in thermally assisted magnetic recording (TAMR) suspension. The TAMR suspension using an optical fiber has high stiffness such as vertical, pitch and roll. Therefore, P-torque is greatly increased by the optical fiber. Also, flying height (FH) of the slider with TAMR suspension can be largely changed by PSA. In this paper, we focus on the FH by PSA of TAMR suspension. The FH is investigated using various PSA and proper PSA is proposed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 B
• /
• pp.287-289
• /
• 2000

Induction heating is utilized in a large and ever-increasing number of application. The most prominent of these are billet heating heat treating, metals joining, and metal melting. In these day, heating roll, a kind of induction heating, is widely used in curing of coatings and fiber industry. In this paper, at first, treated that heating roll's characteristics equation. The second, analysis of magnetic flux and eddy currents distribution using FEM.