• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.11
• /
• pp.836-845
• /
• 2001

A Novel fully-differential bipolar current subtracter(FCS) and its application to current controlled current amplifier(CCCA) for high-accuracy current-mode signal processing were designed. To obtain full-differential current output, the FCS was symmetrically composed of two current follower with low current-input impedance. The CCCA to control output current by the bias current was consisted of the subtracter and a current gain amplifier(CGA) with single-ended current output.. The simulation result shows that the FCS has current-input impedance of 5 Ω and a good linearity. The CCCA has 3-dB cutoff frequency of 20 MHz for the range over bias current 100 $\mu$A to 20 mA. The power dissipation of the FCS and CCCA are 1.8 mW and 3 mW, respectively.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.83-91
• /
• 2007

An experimental verification of multipactor(MP) discharge for S-band diplexer as a sample DUT for space application by an in-house MP test facility is proposed. The designed diplexer having two BPFs for Rx and Tx is applied to a design of five pole inter-digital cavity type band pass filter with chebyshev response, it has 2.7 % bandwidth centered at 2.232 and 2.055 GHz for Rx, Tx, respectively. To avoid the MP discharge, the accurate design and analysis methods based on 3D EM field analysis are considered. The proposed in-house MP test facility consists of a phase detecting system using a doubly balanced mixer as a simple, low cost and real time MP test method compared with results of previously well-known MP detection systems as cross reference methods. The calculated MP threshold RF input power is 43.13 dBm. The measured one is 43 dBm and 44 dBm for CW, pulsed mode test, respectively.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.291-298
• /
• 2013

In this paper a new hybrid-type control system is proposed which reduces the pump speed of an electro-hydraulic actuator consisting of a pressure-compensated variable displacement piston pump and a valve-controlled hydraulic cylinder, whenever the flow rate demand is low. In order to avoid interfering with the pressure regulator which also has an effect on swash plate angle, the pump speed is changed in proportion to the mean value of the speed component of position commands. Additionally a pressure switch is employed to prevent the system pressure from getting lower than a reference value. Based on computer simulation & experimental results, it is shown that the hybrid control can save the idling power up to 44% at a stand-by mode by reducing the pump speed from 1,800 rpm to 600 rpm without affecting the dynamic response of the electro-hydraulic actuator.

• New & Renewable Energy
• /
• v.7 no.3
• /
• pp.67-73
• /
• 2011

MGT fuelled by landfill gas was tested to asses feasibility of its exhaust gas application for $CO_2$ enrichment. The exhaust gas was analyzed during start-up and normal operation with different MGT load conditions. Due to the changes of air/fuel ratio and combustion mode, $O_2$, $CO_2$, CO and NOx concentration were varied within wide ranges during the MGT start-up. Especially, NOx emissioin level was increased up to 20.01 ppmv. Different tendencies of $O_2$, $CO_2$, CO and NOx concentrations were observed with MGT output changes. $O_2$ and CO concentrations were shown to be decreased and NOx and $CO_2$ concentrations were shown to have opposite trends. NOx emission level (0.8~1.88 ppmv) was very low compared to other types of combustion based power generation equipment. Unburned hydrocarbon emission level was substantially decreased with MGT load increase. Especially, $C_2H_4$ concentration was below the detection limit(0.2 ppmv) around the nominal load condition. The exhaust gas from landfill gas fuelled MGT system was shown to be feasible for $CO_2$ fertilization. Concentrations of major components were within or below the maximum allowable ranges.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.2
• /
• pp.29-36
• /
• 2000

The principle and design of two-stage CMOS operational amplifier with rail-to-rail input and class-AB output stage is presented. The rail-to-rail input stage shows almost constant transconductance independent of the common mode input voltage range in global transistor operation region. This new technique does not make use of accurate current-voltage relationship of MOS transistors. Hence it was achieved by using simple linear relationship of currents. The simulated transconductance variation using SPICE is less the 4.3%. The proposed global two-stage opamp can operate both in strong inversion and in weak inversion. Class AB output stage proposed also has a full output voltage swing and a well-defined quiescent current that does not depend on power supply voltage. Since feedback class- AB control is used, it is expected that this output stage can be operating in extremely low voltage. The variation of DC-gain and unity-gain frequency is each 4.2% and 12%, respectively.

• Corrosion Science and Technology
• /
• v.12 no.6
• /
• pp.274-279
• /
• 2013

Flow accelerated corrosion (FAC) of the carbon steel piping in nuclear power plants (NPPs) has been major issue in nuclear industry. During the FAC, a protective oxide layer on carbon steel dissolves into flowing water leading to a thinning of the oxide layer and accelerating corrosion of base material. As a result, severe failures may occur in the piping and equipment of NPPs. Effect of alloying elements on FAC of pipe materials was studied with rotating cylinder FAC test facility at $150^{\circ}C$ and at flow velocity of 4m/s. The facility is equipped with on line monitoring of pH, conductivity, dissolved oxygen(DO) and temperature. Test solution was the demineralized water, and DO concentration was less than 1 ppb. Surface appearance of A 106 Gr. B which is used widely in secondary pipe in NPPs showed orange peel appearance, typical appearance of FAC. The materials with Cr content higher than 0.17wt.% showed pit. The pit is thought to early degradation mode of FAC. The corrosion product within the pit was enriched with Cr, Mo, Cu, Ni and S. But S was not detected in SA336 F22V with 2.25wt.% Cr. The enrichment of Cr and Mo seemed to be related with low, solubility of Cr and Mo compared to Fe. Measured FAC rate was compared with Ducreaux's relationship and showed slightly lower FAC rate than Ducreaux's relationship.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.6
• /
• pp.1-6
• /
• 2014

The IoT (Internet of Things) is considered as a core technology to realize interconnected world. At this, companies composing ICT industry and standard organizations make efforts to accelerate it. IETF CoRE(Constrained RESTful Environment) working group standardized CoAP (Constrained Application Protocol) for the constrained device. CoAP has RESTful architecture and CoAP option is provided to use forward-proxy. The forward-proxy is used to translate protocol and perform requests on behalf of the client. However, communication between Internet based client and LLN(Low-power and Lossy Network) based CoAP server architecture has limitations to deploy real IoT service. In this architecture, problems like response delay, URI assignment and DoS attack can be occurred. To solve these problems, we propose the reverse-proxy based system. We consider both of static IoT and mobility IoT environments. Finally, our proposed system is expected to provide efficient IoT service.

• Superconductivity and Cryogenics
• /
• v.20 no.2
• /
• pp.15-22
• /
• 2018

The present article briefly overviews the plan for a new project on joint technology for HTS wires/cables and describes the development plan for the world's highest field NMR magnet, which is a major development item in the project. For full-fledged social implementation of superconducting devices, high temperature superconducting (HTS) wire is a key technology since they can be cooled by liquid nitrogen and they can generate a super-high magnetic field of >>24 T at liquid helium temperatures. However, one of the major drawbacks of the HTS wires is their availability only in short lengths of a single piece of wire. This necessitates a number of joints being installed in superconducting devices, resulting in a difficult manufacturing process and a large joint resistance. In Japan, a large-scale project has commenced, including two technical demonstration items: (i) Development of superconducting joints between HTS wires, which are used in the world's highest field 1.3 GHz (30.5 T) NMR magnet in persistent current mode; the joints performance is evaluated based on NMR spectra for proteins. (ii) Development of ultra-low resistive joints between DC superconducting feeder cables for railway systems. The project starts a new initiative of next generation super-high field NMR development as well as that of realization of better superconducting power cables.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.37 no.4
• /
• pp.28-34
• /
• 2000

In this paper, a continuous-time filter for low voltage and high frequency applications using fully-balanced current integrators is presented. As the balanced structure of integrator circuits, the designed filter has improved noise characteristics and wide dynamic range since even-order harmonics are cancelled and the input signal range is doubled. Using complementary current mirrors, bias circuits are simplified and the cutoff frequency of filters can be controlled easily by a single DC bias current. As a design example, the 3rd-order lowpass Butterworth filter with a leapfrog realization is designed. The designed fully-balanced current-mode filter is simulated and examined by SPICE using 0.65${\mu}{\textrm}{m}$ CMOS n-well process parameters. The simulation results show 50MHz cutoff frequency, 69㏈ dynamic range with 1% total harmonic distortion(THD), and 4㎽ power dissipation with a 3V supply voltage.

• Geomechanics and Engineering
• /
• v.15 no.4
• /
• pp.927-935
• /
• 2018

The mechanical behavior of the brittle material samples containing the internal and edge cracks are studied under direct shear tests. It is tried to investigate the effects of stress interactions and stress intensity factors at the tips of the pre-existing cracks on the failure mechanism of the bridge areas within these cracks. The direct shear tests are carried out on more than 30 various modeled samples each containing the internal cracks (S models) and edge cracks (E models). The visual inspection and a low power microscope are used to monitor the failure mechanisms of the tested samples. The cracks initiation, propagation and coalescences are being visualized in each test and the detected failure surfaces are used to study and measure the characteristics of each surface. These investigations show that as the ratio of the crack area to the total shear surface increases the shear failure mode changes to that of the tensile. When the bridge areas are fixed, the bridge areas in between the edge cracks have less strength than those of internal cracks. However, the results of this study show that for the case of internal cracks as the bridge area is increased, the strength of the material within the bridge area is decreased. It has been shown that the failure mechanism and fracture pattern of the samples depend on the bridge areas because as the bridge area decreases the interactions between the crack tip stress fields increases.