• Proceedings of the KIEE Conference
• /
• 2004.07e
• /
• pp.62-67
• /
• 2004

In this paper, we present the new method for joint aspect inspecting system. We use the image processing and laser maker for light source. We can find the matrial joint status through processing the line pattern which is made by laser maker. To get the line pattern, in first, we had done the preprocss of threshold. If the shape of line had over two segments, then the joint status is abnormal. We show our system efficency by experiment on tire facility.

• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.163-169
• /
• 2011

This paper introduces a method about water line detection using SAR image. The method includes pre-processing of the SAR image with the threshold of the histogram to recognize the boundary between the water and the landmass area. Finally we applied the image differentiation to detect the water line in the SAR image. The TerraSAR-X and the Cosmo-SkyMed images, which are the high spatial resolution X-band SAR data, are used for the evaluation of our algorithm. The accuracy is verified over the stream line in urban area with the result from the Cosmo-SkyMed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8C
• /
• pp.1149-1158
• /
• 2004

In this thesis, we created a Fuzzy rule in a Fuzzy logic that are Fuzzy logic which is composed of linguistic rules and Fuzzy inference engine for effective traffic control in ATM networks. The parameters of the Fuzzy rules are adapted to minimize the given performance index in both cases. In other words, the difuzzification value controls the threshold in the buffer to arrival ratio to traffic priority (low or high) using fuzzy set theory for traffic connected after reasoning. Also, show experiment result about rule by MATLAB6.5 and on-line bulid-up to verify validity of created Fuzzy rule. As a result, we can verify that threshold value in buffer is efficiently controlled by the traffic arrival ratio.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.167-170
• /
• 2016

Replica bit-line technique is used for making enable signal of sense amplifier which accurately tracks bit-line of SRAM. However, threshold voltage variation in the replica bit-line circuit changes the cell current, which results in variation of the sense amplifier enable time, $T_{SAE}$. The variation of $T_{SAE}$ makes the sensing operation unstable. In this paper, in addition to conventional replica bit-line delay ($RBL_{conv}$), dual replica bit-line delay (DRBD) and multi-stage dual replica bit-line delay (MDRBD) which are used for reducing $T_{SAE}$ variation are briefly introduced, and the maximum possible number of on-cell which can satisfy $6{\sigma}$ sensing yield is determined through simulation at a supply voltage of 0.6V with 14nm FinFET technology. As a result, it is observed that performance of DRBD and MDRBD is improved 24.4% and 48.3% than $RBL_{conv}$ and energy consumption is reduced which 8% and 32.4% than $RBL_{conv}$.

• Imaging Science in Dentistry
• /
• v.48 no.4
• /
• pp.255-259
• /
• 2018

Purpose: This study proposes a new ball-type phantom for evaluation of the image layer of panoramic radiography. Materials and Methods: The arch shape of an acrylic resin phantom was derived from average data on the lower dental arch in Korean adult males. Metal balls with a 2-mm diameter were placed along the center line of the phantom at a 4-mm mesiodistal interval. Additional metal balls were placed along the 22 arch-shaped lines that ran parallel to the center line at 2-mm buccolingual intervals. The height of each ball in the horizontal plane was spaced by 2.5 mm, and consequently, the balls appeared oblique when viewed from the side. The resulting phantom was named the Panorama phantom. The distortion rate of the balls in the acquired image was measured by automatically calculating the difference between the vertical and horizontal length using $MATLAB^{(R)}$. Image layer boundaries were obtained by applying various distortion rate thresholds. Results: Most areas containing metal balls (91.5%) were included in the image layer with a 50% distortion rate threshold. When a 5% distortion rate threshold was applied, the image layer was formed with a small buccolingual width along the arch-shaped center line. However, it was medially located in the temporomandibular joint region. Conclusion: The Panorama phantom could be used to evaluate the image layer of panoramic radiography, including all mesiodistal areas with large buccolingual width.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.5
• /
• pp.74-81
• /
• 2019

This study reports the CW $CO_2$ laser scribing of soda lime glass. In this study, scribing experiments are carried out at different laser powers, scan speeds, and focal positions to investigate the effect of the process parameters on the interaction characteristics between a laser beam and glass. In particular, the interaction characteristics are analyzed and described with the input laser energy per unit length. According to the experimental results, the damage threshold for the glass surface was found to exist between 0.072 and 0.08 J/mm. The input laser energy in this region induced partial melting of the surface and grain-shaped cracks. These cracks tended to increase as the input laser energy increased. At the laser input energy larger than 1 J/mm, a huge crack propagating along the scan direction was produced, and the volume below the scribed area was fully melted. The growth of this crack finally resulted in the complete cutting of the glass at the input laser energy above 8 J/mm. It was found that both the width and depth of the scribed line increased with increasing input laser energy. For the beam focusing at the rear surface, the width of the scribed line varied irregularly. This could be ascribed to the increased asymmetry of the beam intensity distribution when the laser beam was focused at the rear surface. Under this condition, a large burr was only produced on one side of the scribed line.

• Journal of Korea Multimedia Society
• /
• v.12 no.11
• /
• pp.1547-1556
• /
• 2009

In this paper, we propose a flame detection method using region expansions and on-line variances in outdoor infrared video sequences. To segment flame candidates' regions in infrared images, we first, extract initial regions by high threshold values in infrared images and then the segmented regions are expanded to their neighbors with similar high intensity values. The segmented regions could be non-flame areas like bare-grounds and buildings. Therefore, to detect flame regions in the segmented regions, the segmented regions which have high intensity values in infrared image, are tracked using bounding regions in frame sequences. Variances in the tracked regions are calculated effectively by on-line updates to measure intensity variations on the tracked regions. Experiments show that the proposed method, which is based on region expansions and the average of on-line variances in the regions, is efficient to detect flames in infrared image.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2263-2268
• /
• 2008

We investigated the malfunction and destruction characteristics of microcontroller devices under high power electromagnetic(HPEM) wave by magnetron. HPEM was rated at a microwave output of 0 to 1,000 W, at a frequency of 2,450${\pm}$50 MHz and was radiated from the open-ended standard rectangular waveguide(WR-340) to free space. The influence of different reset-, clock-, data-, and power supply-line lengths has been tested. The variation of the line length was done with flat cables. The susceptibility of the tested microcontroller devices was in general much influenced by clock-, reset-, and power supply-line length, little influenced by data-line length. Further the line length was increased, the malfunction threshold was decreased as expected, because more energy couples to the devices. The surfaces of the destroyed microcontroller devices were removed and the chip conditions were investigated with microscope. The microscopic analysis of the damaged devices showed component and bondwire destructions such as breakthroughs and melting due to thermal effects. The obtained results are expected to provide fundamental data for interpreting the combined mechanism of microcontroller devices in an intentional microwave environment.

• Tribology and Lubricants
• /
• v.6 no.1
• /
• pp.74-81
• /
• 1990

The threshold of instability for a rigid rotor supported in externally pressurized airlubricated circular or non-circular journal bearings of finite length is theoretically analyzed. The analysis is performed for a bearing having one feeding plane, no recess volume, which is assumed to be a line source, and is based on a first order perturbation of journal center motion about steady state position. And then linearized system dynamic analysis is carried out. Numerical results are given, showing the threshold of instability as a function of supply pressure ratio, feeding parameter and load. It is shown that the region that 2-lobe bearing is more stable than circular bearing exists and whirl ratio of 2-lobe bearing is less than that of the other types of bearing.

• Journal of information and communication convergence engineering
• /
• v.10 no.4
• /
• pp.378-383
• /
• 2012

This paper presents the implementation of an automatic road sign recognizer for an intelligent transport system. In this system, lists of road signs are processed with actions such as line segmentation, single sign segmentation, and storing an artificial sign in the database. The process of taking the video stream and extracting the road sign and storing in the database is called the road sign recognition. This paper presents a study on recognizing traffic sign patterns using a segmentation technique for the efficiency and the speed of the system. The image is converted from one scale to another scale such as RGB to grayscale or grayscale to binary. The images are pre-processed with several image processing techniques, such as threshold techniques, Gaussian filters, Canny edge detection, and the contour technique.