• Wind and Structures
• /
• v.3 no.3
• /
• pp.143-158
• /
• 2000

This report presents the findings of a one-year monitoring effort to empirically characterize and evaluate the nature of near-ground winds for structural engineering purposes. The current wind engineering practice in the United States does not explicitly consider certain important near-ground wind characteristics in typical rough terrain conditions and the possible effect on efficient design of low-rise structures, such as homes and other light-frame buildings that comprise most of the building population. Therefore, near ground wind data was collected for the purpose of comparing actual near-ground wind characteristics to the current U.S. wind engineering practice. The study provides data depicting variability of wind speeds, wind velocity profiles for a major thunderstorm event and a northeaster, and the influence of thunderstorms on annual extreme wind speeds at various heights above ground in a typical rough environment. Data showing the decrease in the power law exponent with increasing wind speed is also presented. It is demonstrated that near-ground wind speeds (i.e., less than 10 m above ground) are likely to be over-estimated in the current design practice by as much as 20 percent which may result in wind load over-estimate of about 50% for low-rise buildings in typical rough terrain. The importance of thunderstorm wind profiles on determination of design wind speeds and building loads (particularly for buildings substantially taller than 10 m) is also discussed. Recommendations are given for possible improvements to the current design practice in the United States with respect to low-rise buildings in rough terrain and for the need to study the impact of thunderstorm gust profile shapes on extreme value wind speed estimates and building loads.

• The Journal of the Korea Contents Association
• /
• v.9 no.11
• /
• pp.10-17
• /
• 2009

Wyner-Ziv video coding is a new video compression paradigm based on distributed source coding theory of Slepian-Wolf and Wyner-Ziv. Wyner-Ziv coding enables light-encoder/heavy-decoder structure by shifting complex modules including motion estimation/compensation task to the decoder. Instead of performing the complicated motion estimation process in the encoder, the Wyner-Ziv decoder performs the motion estimation for the generation of side information in order to make the predicted signal of the Wyner-Ziv frame. The efficiency of side information generation deeply affects the overall coding performance, since the bit-rates of the Wyner-Ziv coding is directly dependent on side information. In this paper, an improved side information generation method using field coding is proposed. In the proposed method, top fields are coded with the existing SI generation method and bottom fields are coded with new SI generation method using the information of the top fields. Simulation results show that the proposed method improves the quality of the side information and rate-distortion performance compared to the conventional method.

• Journal of the Korean Society of Safety
• /
• v.33 no.5
• /
• pp.15-20
• /
• 2018

This paper describes the fusing time characteristics of Light PVC Sheathed Circular Cord(VCTF) and Tray Frame Retardant(TFR) cables according to increased temperature under over current condition. The experimental equation will be used to determine the validity and reliability of the test results. The over current flowed 3, 5 and 10 times higher than the amount of allowable current using DC power supply with DAQ(Data Acquisition) measurement system. An infrared radiation heater, which was controlled by a variable AC auto transformer, was used to increase the temperature from room temperature to 50, 100 and 150 degrees Celsius. First, two type of cables were analyzed those with different cross-sectional areas with in the same structure and those with different structures with in the same cross-sectional areas. Then, it was determined how fusing time had been influenced according to the cross-sectional areas and different structures, respectively. The cable resistance was increased by joule heating according to increasing temperature. Therefore, the allowable current of cable is decreased. Finally, the fusing time of the cable was decreased due to increased temperatures at current flow, which were 3 times the amount of allowable current. The instantaneous breakdown was observed when current flow was 5 and 10 times over the amount of allowable current. The fusing time is directly affected by the structure of cable insulation.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.3
• /
• pp.211-220
• /
• 2013

The nailed joints in wood construction are commonly designed to resist and carry the lateral load but also subject to withdrawal force like uplift load due to the wind. This research was conducted to evaluate the performance of nailed joint composed of dimension lumber and sheathing materials through the nail withdrawal and unsymmetric double shear joint test, and then compared to current design values. The withdrawal strength was greatly dependant on wood specific gravity, and the withdrawal strength of I-joist with OSB showed higher value in spite of low specific gravity. The maximum withdrawal loads were greater than that of derived current design values about 5 times. The lateral resistance of Japanese larch/OSB nailed joints was higher than that of SPF/OSB nailed joint, and derived allowable lateral strength of nailed joints in this study exceeded the current design values. The failure mode of nailed joints was primarily due to the nail bending and this tendency was notable in SPF/OSB nailed joint.

• Journal of ILASS-Korea
• /
• v.13 no.4
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• Journal of the Korean Geographical Society
• /
• v.49 no.2
• /
• pp.178-199
• /
• 2014

Changwon Industrial Complex is commonly framed as the best example of strong initiative of the Korean developmental state. And this explanation has been given in the theoretical frame of 'neo-Weberian accounts' i.e., strongly 'national-territorial' and state-centric terms of the predominant. I argue that a geopolitical economy approach focusing on the historical background of the development of Changwon Industrial Complex will shed light on crucial sociospatial dimensions of the Korean developmental state's industrial complex success. I examine, in particular, the multi-scalar processes through which the changes of the industrial complex building plans for the promotion of machine industry in 1960's have been influenced by the complex and dynamic interactions among social actors acting at diverse geographical scales. I show that the formation of the industrial complex in Korea was more heavily influenced by the interactions, contestations, and collaborations among social actors, acting in and through the state, rather than by the state initiative.

• Journal of Agricultural Extension & Community Development
• /
• v.20 no.2
• /
• pp.341-382
• /
• 2013

The purpose of this study is to introduce 'Bogoganeun Maeul Movement' which was drived by Jellabuk-do province at 1962. and to ascertain historical meaning of its among history of Korea rural development and to investigate the relationships among 'Sinsanghwal movement', 'Community development program', 'Jaegungukmin movement'. It was found that 4,031 Maeul was designated a Bogaganeun Maeul at 1962. and leader of its village got an appointment as 'light of rural' by province administration. This study was found that the historical meaning that even if it was in theoretically and administrative frame. Bogaganeun Maeul was a self-regulating first community development program that was drived by Jeollabuk-do and starting point of model of 'Mobum Burak'. Besides Bogaganeun Maeul was tourism village for an inspection and learning by observation. and first article that 'Sightseeing village' word appeared initially in the newspaper.

• Journal of Plant Biotechnology
• /
• v.7 no.1
• /
• pp.67-74
• /
• 2005

To overcome various disadvantages of conventional cul-ture vessels for micropropagation, a novel disposable vessel, the 'Vitron', made of a multi-layered $OTP^{(R)}$ film and supported by a polypropylene frame, was developed. The film possesses superior properties such as: high light transmittance, low water vapor transmittance and thermal stability and in particular, high gas-permeability. Single nodal explants, which were excised from the multiple shoots derived from shoot-tip culture, were cultured in Vitron and polycarbonate vessels on $3\%$ sugar-containing agar on MS medium and placed at 3000 ppm $CO_2$-enrichment at a low photosynthetic photon flux density (PPFD) ($45{\mu}mol\;m^{-2}\;s^{-1}$). The in vitro and ex vitro growth, and the net photosynthetic rate of in vitro and ex vitro plantlets were significantly enhanced in the Vitron compared to those cultured in a polycarbonate vessel. Explants that were cultured on the same MS medium under low PPFD at various $CO_2$ concentrations were also cultured at 3000 ppm $CO_2$- enrichment at various PPFD: 30, 45, 60, 75 and $90{\mu}mol\;m^{-2}\;s^{-1}$. The best in vitro and ex vitro growth obtained for 3000 ppm $CO_2$-enrichment at $75{\mu}mol\;m^{-2}\;s^{-1}$ PPFD. The novel Vitron vessel, when placed under the two conditions, may replace conventional culture vessels for the successful micropropagation of sweetpotato.

• Korean Journal of Plant Resources
• /
• v.18 no.3
• /
• pp.441-449
• /
• 2005

Photo system II (PSII) is one of the two photosynthetic reaction centers in the chloroplast of higher plants. The chlorophyll a/b-light harvesting complex serves primarily as an antenna for PSII. We isolated a cDNA that encodes a chlorophyll a/b-binding protein (Cab) from Panax ginseng. The small subunit consists of 935 nucleotides long and has an open reading frame of 795 bp with the deduced amino acid of 265 residues (pI 5.63), 28.6 kDa. The deduced amino acid sequence matched to the previously reported Cab genes. Their degree of amino acid identity ranged from 68 to $92\%$. Phylogenetic analysis based on the amino acid residues was showed that the ginseng Cab gene was grouped with P. persica (AAC34983), A. thaliana (AAD28771), G. hirsutum (CAA38025), G. max (AAL29886), and V. radiate (AAF89205).

• Archives of design research
• /
• v.17 no.4
• /
• pp.401-404
• /
• 2004

The proposal defines a Do It Yourself system that radically changes the traditional concept of window. it is based on a D.I.Y. system that allows the users to fully customize its windows according to his needs, combining a wood frame with different elements. At the same time, it is preserving the basic function of light and ventilation and defining a new aesthetic code. Despite the restriction of size and shape, the user can choose among many different elements to increase the space efficiency he needs and to give a more enjoyable perspective to the window both in and out door. Also, All the elements are standard and they can be mass-produced according to specific market needs. Therefore, the window of the future will not be just a thin membrane in between the inside and the outside, but it will also play an important "identification role. According to each individual pick, these new windows will help to give identify to anonymous metropolitan areas and to the people living within them.