• 한국항공우주학회지
• /
• 제45권3호
• /
• pp.173-179
• /
• 2017

본 논문에서는 모션캡쳐 카메라를 사용한 실험을 통해 날갯짓 비행체의 주 날개, 꼬리날개 구동기 특성 분석에 대하여 기술하였다. 실험은 빛이 차단된 실내에서 진행되었고 지그에 기체를 고정하여 날갯짓으로 인한 영향을 줄였다. 주 날개와 꼬리날개 끝단에 마커를 부착하였고 모션캡쳐 카메라는 입력 신호에 대한 각각의 반응을 측정한다. 실험 결과 주 날개는 날갯짓의 주파수에 따라 진폭이 변하는 경향을 보였고, Modified Strip Theory에 실험 결과와 비행체 제원을 적용하여 양력 및 추력 발생 시뮬레이션을 구현 하였다. 꼬리날개는 종 횡축별로 스텝 신호를 인가하여 이에 따른 결과를 2차 전달함수 형태로 정의하였고, 각 축별로 구동기의 구조 차이로 인하여 최종 응답시간, 오버슈트, 최대값 등에서 차이를 나타내는 것을 확인하였다.

• 한국정밀공학회지
• /
• 제28권6호
• /
• pp.709-715
• /
• 2011

Chattering in cutting operations are usually a cumbersome part of the manufacturing process in mechanical. Particular, machining performance such as that of the boring process is limited by cutting condition at the movable components. Among various sources of chatter vibration, detrimental point in cutting condition is found a mechanical condition on overhang. It limits cutting speed, depth, surface roughness and tool wear failure as result because the all properties are varying with the metal removal process. In this case, we have to observe the resonance frequencies of a boring bar for continuous cutting. In the established research, boring bar vibration of cutting system has been measured with the aid of accelerometer. However, the inherent parameters of internal turning operations are severely limit for the real time monitoring on accelerometers. At this point, this paper is proposed other method for real time monitoring during continuous cutting with optical fiber at the inside of boring bar. This method has been used a plastic fiber in the special jig on boring bar by based on experimental modal analysis. In this study, improvement of monitoring system on continuous internal cutting was attempted using optical fiber sensor of inside type because usually chattering is investigated experimentally measuring the variation in chip thickness. It is demonstrated that the optical fiber sensor is possibility to measure of chattering with real time in boring process.

• 대한조선학회논문집
• /
• 제52권6호
• /
• pp.460-470
• /
• 2015

In general ships and FPSOs, roll damping is very small and consequently roll motion is very large at the roll resonance frequency. Proper evaluation of the roll damping coefficient at the resonance frequency is an important task in the study of roll motion and usually it is done by the analysis of free roll decay tests. The relative decrement method based on energy relation has been used mainly for the evaluation of roll damping coefficient from the roll decay test so far. As another method, the logarithmic decrement method based on equivalent linear decay assumption can be used for the same purpose and it is relatively simple. In this paper, both of the relative decrement method and the logarithmic decrement method are used for the evaluation of roll damping coefficient including quadratic damping from the free roll decay tests, and their results are cross-checked for verifying the obtained damping coefficients. Through applications to a box-type floating body equiped with bilge keels, it is shown that the two methods give almost the same damping coefficients in a practical view point and the cross-check of their results is to be a good tool to prevent a possible error. And also the quantitative effects of the bilge keels on the roll damping of box-type floating body are shown and discussed.

• 한국산업보건학회지
• /
• 제19권3호
• /
• pp.280-287
• /
• 2009

High-tech microelectronics industry is known as one of the most chemical-intensive industries. In Korea, Microelectronics industry occupied 38% of export and 16% of working employees work in microelectronics industry. But, chemical information and health hazards of high-tech microelectronics manufacturing are poorly understood because of rapid development and its penchant for secrecy. We need to investigate on chemical use and exposure control. We Site-visits to 6 high-tech microelectronics manufacturing company which have cleanroom work using over 1,000kg organic solvents (5 semi-conductor chips and its related parts company, 1 liquid crystal display (LCD)). We reviewed their data on chemical use and ventilation system, and measured TVOCs (Total Volatile Organic Compounds) and carbon dioxide concentration. All cleanroom air passed through hepa filters to acheive low particle levels and only 1 cleanroom uses carbon filters to minimize the organic solvents exposures In TVOC screening test, Cleanroom for semi-conductor chips and its related parts company with laminar down flow system (e.g. class 1~100) showed nondetectable level of TVOCs concentration, but Cleanroom for liquid crystal display (LCD) with conventional flow system (e.g. class 1,000~10,000) showed 327 ppm as TVOCs. Acetone concentration in cleanroom for Jig cleaning, LC Injection, Sealing processes were 18.488ppm (n=14), 49.762 ppm (n=15), 8.656 ppm (n=14) as arithmetric mean. Acetone concentration in cleanroom for LCD inspection process was 40ppm (n=55) as geometric mean, where the range was 7.8~128.7ppm and weakly correlated with ventilation rate efficiency(r=0.44, p<0.05). To control organic solvents in cleanrooms, chemical and carbon filters should be installed with hepa filters. Even though their volatile organic compounds concentration was not exceed to occupational exposure limits, considering of entrance limited cleanroom environment, long-term period exposure effects and adverse health effects of cleanroom worker need further reseach.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.135-141
• /
• 2005

Measurement of five DOF motion errors in a ultra precision feed table was attempted in this study. Yaw and pitch error were measured by using a laser interferometer and roll error was measured by using the reversal method. Linear motion errors in the vertical and horizontal directions were measured by using the sequential two point method. In this case, influence of angular motion errors was compensated by using the previously measured ones by the laser interferometer and the reversal method. The capacitive type sensors and an optical straight edge were used in the reversal method and the sequential two point method. Influence of thermal deformation on sensor jig was investgated and minimized by the periodic measurement according to the variation of room temperature. Deviation of gain between sensors was also compensated using the step response data. 5 DOF motion errors of a hydrostatic table driven by the linear motor werer tested using the measurement method. In the horizontal direction, measuring accuracies for the linear and angular motion were within ${\pm}0.02\;{\mu}m$ and ${\pm}0.04$ arcsec, respectively. In the vertical direction, they were within ${\pm}0.02{\mu}m$ and ${\pm}0.05$ arcsec. From these results, it was found that the introduced measurement method was very effective to measure 5 DOF motion errors of the ultra precision feed tables.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 제5회 압출 및 인발가공 심포지엄
• /
• pp.43-49
• /
• 2002

A7003 alloy has characteristics of their excellent weldability, high corrosion resistance and superior plastic working however the broadening of application for the alloy has been hampered by the lower extrudability associated by Mg content. For improvement of extrudability and enhanced recovery efficiency during Al scrap recyeling, it has been generally practiced to reduce Mg content in A7003 alloy. Therefore, it is necessary to investigate the influence of Mg content on mechanical strength and extrudability of A7003 alloy. For efficient material processing which has small amounts, life cycle assessment in material processing(MLCA) is evaluated. The quantitative analysis of energy requirements and $CO_2$ emission for production of A7003 extruded bar are estimated with different Mg content and billet pre-heating process (heating source by light oil or LPG). In particular, the estimation of energy requirements was performed within shipping and gating range (except the mining and extraction stages)to investigate the influence of the variables on energy requirements and $CO_2$ emission in detail. As Mg content increased, the flow stress and the extrusion pressure for A7003 alloy increased. It has been thought that an increment in extrusion pressure with increasing Mg content is caused by the solid solution hardening of Mg atoms in the matrix and increment in volume fraction of intermetallic compound, $Mg_2Si$. The extrudability and the tensile strength are equal to, or above that of conventional A 7003 alloy even the content of Mg varied from $1.1wt.\%\;to\;0.5wt.\%$ alloy. This means that minimizing the content of Mg in A7003 alloy can enhance recovery efficiency during Al scrap recycling. It can be quoted that rather than Mg content energy source for billet heating is a prime factor to determine the atmospheric $CO_2$ emission.

• 수산해양기술연구
• /
• 제51권4호
• /
• pp.520-526
• /
• 2015

A tragic disaster happened by capsizing O-Ryong 501 trawler at Western Bering Sea in 1st, Dec. 2014. The disaster was caused by the severe weather and the long deferred escape from the storm in fully developed high sea. Lots of sea water from poop deck rushed into the fish ponder with fishes all together after hauling net and then remove the fishes from codend. The vessel became to incline to the one side caused by the weight and the free surface effect of flood sea waters and fishes at initial stage. In spite of crews all effort to discharge the waters, but the work was not achieved successfully. For the worse thing, the order of abandon ship was issued too late. After all, the ship capsized and sank, then almost crews became to the victims of the casualty including captain. In this paper, author carried out restrictively the calculation of dynamic factors influenced on the disaster including the weather condition and effects of the flood sea waters, and found out that the most important causes of the disaster were the decrease of stabilities, GM was decreased from 0.9m to 0.08 m, and the high waves which led to the vessel disaster.

• 한국인터넷방송통신학회논문지
• /
• 제14권1호
• /
• pp.119-124
• /
• 2014

본 논문에서는 한 보드에서 GPS/GLONASS 대역을 이용하여 컨테이너의 위치정보를 확인 할 수 있고, 위치 정보를 실시간으로 이동통신망으로 전송 할 수 있는 GSM/WCDMA 대역의 안테나를 설계하였다. GPS(1.575.42MHz)와 GLONASS(1.602MHz) 듀얼 대역을 지원하는 마이크로스트립 패치 안테나를 최적화하였고, 안테나의 크기는 $25{\times}25{\times}5[mm]$이다. GSM(824-960MHz)와 WCDMA(1970-2170MHz) 이중대역을 지원하는 칩 모노폴 안테나를 최적화 하였고, 안테나의 크기는 $27{\times}8{\times}3.2[mm]$이다. 위성 수신레벨을 증폭하기 위해 2단 저잡음 증폭기(LNA)를 설계하였고. LNA 이득은 27[dB]이다. 안테나의 측정지그의 크기는 $100{\times}30{\times}1[mm]$이다.

• 한국인터넷방송통신학회논문지
• /
• 제14권5호
• /
• pp.203-208
• /
• 2014

본 논문에서는 내장형 안테나의 일종인 IFA 구조를 이용하여 433MHz용 소형 능동 RFID 안테나를 제안하였다. 제안한 안테나에서 급전점과 단락스트립 사이의 간격 변화, 복사기에 미엔더 라인 구조를 삽입, 복사기와 접지면 사이 간격 변화를 주어 안테나 성능을 개선하였다. 안테나 파라미터 특성에 확인하기 위하여 ANSYS사의 HFSS를 이용하였다. 433MHz 능동형 RFID 주파수 대역은 433.67-434.17MHz이다. 제작한 안테나는 433MHz 능동형 RFID 대역에서 반사손실 -9.54dB이하의 값을 가지며, 최대 안테나 이득은 -4.28dBi임을 확인할 수 있다. 제안한 안테나의 전체 지그 크기는 $72{\times}44{\times}1mm$이고, 안테나 부분은 $35.5{\times}19.5mm$이다. 안테나의 측정결과와 시뮬레이션 결과를 비교하여 분석한 결과, IFA 구조를 이용한 소형 433MHz 안테나의 실용화 가능성을 확인 할 수 있었다.

• 대한치과보철학회지
• /
• 제45권1호
• /
• pp.12-20
• /
• 2007

Purpose: The purpose of this study was to compare the fracture strength of the zirconia monolithic all-ceramic crowns according to the thickness (0.5mm, 0.8mm, 1.1mm) and metal-ceramic crowns (1.0mm, 1.5mm) Material and method: Twelve crowns for each of 3 zirconia crown groups were fabricated using CAD/CAM system (Kavo, Germany) and twelve crowns for each of 2 metal-ceramic crown groups were made by the conventional method. All crowns were luted to the metal dies using resin cement. Half of the specimens were exposed to thermocycling ($5-55^{\circ}C$, 1 Hz) and cyclic loading (300,000 cycles, 50N). Subsequently, all crowns were mounted on the testing jig in a universal testing machine. The load was directed at the center of crown with perpendicular to the long axis of each specimen until catastrophic failure occurred. Analysis of variance and Tukey multiple comparison test (P<.05) were used for statistical analysis of all groups, and paired t-test (P<.05) was followed for statistical comparison between each groups' fracture load before and after cyclic loading. Results: 1. The fracture strength of the zirconia monolithic crowns and the metal-ceramic crown increased as thickness increased (P<.05). 2. The cyclic loading and thermocycling significantly decreased the fracture strength of the zirconia monolithic crowns (P<.05). 3. The standard deviation of fracture strength of the zirconia monolithic crowns was very low. Conclusion: The fracture strength of the zirconia monolithic crowns for the posterior area tends to be higher with thickness increased and 0.8mm or over in thickness is recommended to have similar or over the fracture strength of metal-ceramic crowns.