• Geophysics and Geophysical Exploration
• /
• v.12 no.3
• /
• pp.255-262
• /
• 2009

Conventionally, vertical-seismic-profiling (VSP) survey that provides high-resolution information has mainly performed to obtain the exact depth of the gas hydrate-bearing sediment, which is one of the key factors in the development of the gas hydrate. In this study, we extracted interval velocities and created corridor stacks from the first domestic zero-offset VSP data, which were acquired with three component receivers at UBGH09 borehole in Ulleung Basin where gas hydrate exists. Then we compared the corridor stacks with a CMP stacked section from surface seismic data. First of all, we converted the signals recorded with three component receivers to true vertical and horizontal components by phase rotation, and divided the data into direct waves and reflected waves by wavefield separation processing. The trend of the interval velocity extracted from the zero-offset VSP was similar to that of the sonic log obtained at the same borehole. Because the interval velocity of the gas hydrate-bearing sediment above the BSR was high, and it decreased suddenly through the BSR, we could infer that free gas is accumulated below the BSR. The results of comparing the corridor stacks to the CMP stacked section of the surface seismic data showed that most reflection events agreed well with those in the surface CMP stacked section and that the phase-rotated VSP data corresponded better with the surface seismic data than the VSP data without phase rotation. In addition, by comparing a corridor stack produced from the transverse component with the CMP stacked section of the surface seismic data, we could identify PS mode-converted reflections in the CMP stacked section.

• Journal of Environmental Science International
• /
• v.21 no.5
• /
• pp.613-622
• /
• 2012

A pilot-scale pulse-jet bagfilter was designed, built and tested for the effects of four operating conditions (filtration velocity, inlet dust concentration, pulse pressure, and pulse interval time) on the total system pressure drop, using coke dust from a steel mill factory. Two models were used to predict the total pressure drop according to the operating conditions. These model parameters were estimated from the 180 experimental data points. The empirical model (EM) with filtration velocity, areal density, inlet dust concentration, pulse interval time and pulse pressure shows the best correlation coefficient (R=0.971) between experimental data and model predictions. The empirical model was used as it showed higher correlation coefficient (R=0.971) compared to that of the Multivariate linear regression(MLR) (R=0.961). The minimum pulse pressure predicted by empirical model (EM) was 5kg/$cm^2$.

• Korean Journal of Applied Biomechanics
• /
• v.28 no.2
• /
• pp.79-85
• /
• 2018

Objective: This study aimed to create a strategic training method to enhance optimal athletic ability using information from 1H to 10H rhythmic units. Method: Top three world class athletes and three national winners of 110-m hurdle finals from the 2010 Daegu International Athletics Competition and 2017 National Athletics Championship, respectively, were selected. To analyze the kinematic variables, Dartfish 9.0 was used for two-dimensional analysis. Results: Regarding the interval time from the start to the finish line, the national athletes took less time during the pure acceleration phase (start to 1H) than the foreign athletes. The horizontal velocity increase was slower after 1H; the national athletes showed a lack of ability to accelerate at the interval phases. Moreover, the hurdle clearance time between phases was longer in the national athletes than in the foreign athletes and lacked consistency. Conclusion: The national athletes lacked the ability to accelerate at the transition, maximum rhythm, rhythm maintenance, and re-acceleration phases and showed a longer hurdle clearance time. If technical improvements and strategic training methods using rhythmic units are applied for hurdling motions, the national athlete's hurdling abilities, performance, and consistency could improve.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.4
• /
• pp.537-542
• /
• 2007

This paper proposes a 2-step Kalman filter model for land vehicle navigation using civilian-band GPS measurements. The velocity bias caused by the Earth#s rotation would be removed completely when applying this model. Because the linearization of velocity equations in this model is not necessary, the error is significantly reduced. The experiment reveals that estimated position error with stationary data is about 5m during a 15-20 minute interval. The other benefit of this model is that it can be feasibly applied as a GPS receiver module thanks to the small sizes of the necessary manipulating matrices.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.413-422
• /
• 2004

The flow characteristic in the wake around a circular cylinder with tripping wires, which was set in constant distance, was experimentally investigated in the uniform flow, Re=2.92$\times10^4$. The measurement of velocity vector and pressure distribution are carried out various angles of tripping wires in the range of $50^(\circ)$ to $80^(\circ)$ with $10^(\circ)$ interval. The results show that velocity profiles and pressure distributions are different with angles of tripping wires. The drag of the circular cylinder was decreased about 60% maximum when tripping wires' angle was $50^(\circ)$. The lowest reduction of the velocity and wake width was occurred by coanda effect when the angle was $60^(\circ)$, and the vortex shedding periodicity become rare at the same time.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.3
• /
• pp.291-297
• /
• 2000

This paper presents an attitude determination algorithm for the local level strapdown inertial navigation where the body the earth and the transport rate can be calculated separately using a DCM computation scheme, Also presented is a velocity determination algorithm taking into account the attitude variation caused by he change of the navigation frame. The proposed algorithm are implemented using three samples of the velocity and the angle within the integration interval.

• Geophysics and Geophysical Exploration
• /
• v.5 no.3
• /
• pp.141-144
• /
• 2002

Three-dimensional seismic data, recorded with an interval of one year, indicate a velocity changes in the medium at the near surface. During that period of a year, the ground reinforcement work has been conducted at the railroad base in the study area. The time-thickness to the first reflector of the two data were picked and compared. The result showed that the velocity of the medium decreased at large part of the study area; however, no velocity decrease at the railroad base.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.3
• /
• pp.386-393
• /
• 2008

A position control method for interpolating aspherical grinding and polishing tool path was reviewed and experimented in a nano precision machine. The position-base algorithm was reformed from the time-base algorithm, proposed in the previous study. The characteristics of the algorithm were in the velocity control loop with position feedback. The aspherical surface was divided by an interval at which each velocity and acceleration were calculated. The theoretical velocity was corrected by position error during processing. In the experiment, a machine was constructed and nano-scale linear encoders were installed at each axis. Relation between process parameters and the variation of position error was monitored and discussed. The best result from optimized parameters showed that the accuracy was 150nm and improved from the previous report.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.2
• /
• pp.206-216
• /
• 1986

In this paper, the moving distance and velocity of a single moving object are measured by sampling three frames in a two-dimensional line sequence image. The brightness of each frame is analyzed, and the bit data of their pixel are rearranged so that the difference image may be extracted. The parameters for recognition of the object are the gray level of the object, the number of vertex points and the distance between the vertex points. The moving distance obtained from the coordinate which is constructed by the bit processing of the data in the memory map of a microcomputer, and the moving velocity is obtained from the moving distance and the time interval between the first and second sampled frames.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.135-146
• /
• 2003

Uphole test is a seismic field test using receivers on ground surface and a source in depth. In this paper, the uphole test using SPT(standard penetration test) which is economical and reliable for obtaining shear wave velocity profile was introduced. In the proposed uphole test, SPT sampler which is common in site investigation, was used as a source and several 1Hz geophones in line were used as receivers. Test procedures in field and interpretation methods for obtaining interval times and for determining shear wave velocity profile considering refracted ray path were introduced. Finally, uphole test was performed at three sites, and the applicability of the proposed uphole test was verified by comparing wave velocity profiles determined by the uphole test with the profiles determined by downhole test, SASW test and SPT-N values.