• Journal of Welding and Joining
• /
• v.4 no.1
• /
• pp.32-39
• /
• 1986

This paper was studied about the influence of oxidized films on workability in cold pressure welding. In preceding studies, the principal foci of the studies about pressure welding were considered several factors(surface manufacturing methods, surface roughness, pressure welding speed and surface temperature). But the influence to the growth of oxidation have hardly known well. So the purpose of this paper consists in solving the question above and proposing the optimal states of the pressure welding. Therefore the results obtained is as the following; When the oxidation time is within about 2 minutes, the bonding strength is very good after surface manufacturing of the neighboring to be bonded. The more surfaces are fine the more bonding strength is excellent. Above all, the optimal condition of cold pressure welding is the state that the characteristic value is 38% with smooth surface and without oxidation.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1061-1064
• /
• 1998

To examine the influence of unsteady wake on the flow and heat transfer characteristics, an experiment has been conducted in a four-vane linear cascade. Flow and heat transfer measurements are made for the inlet Reynolds number of 66000(based on chord length and free-stream velocity). Turbulent intensity and stress were measured using hot wire anemometer, and to measure the convective heat transfer coefficients on the blade surfaces liquid crystal/gold film Intrex technique was used. The disturbance by the unsteady wake is characterized by the unresolved unsteadiness. The unsteady wake enhances the turbulent motion of flow in the cascade passage. It also promotes the boundary layer development and transition. The results show that heat transfer coefficients on the suction surface increase with increasing unresolved unsteadiness.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.318-323
• /
• 2003

In order to polish complicated shaped inner surfaces of molds, a new polishing method with consolation liquid was Invented The MAGIC (MAGnetic Intelligent Compound) Polishing is the best method, a countermeasure of polishing trouble that is reduce of productivity and instability of quality. But because MAGIC polishing is new polishing method there is no study of the standardization of polishing by MAGIC wheel yet. So we want to standadize MAGIC polishing condition. For the First time, we will evaluate the influence of composition ratio and kind of polishing grain in polishing surface roughness. In this study, we determined amount of dressing oil and dressing point as kind and composition ratio of polishing grain. we compared surface roughness case by case

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1647-1654
• /
• 2001

The hole drilling method is widely used in measuring residual stress in surfaces. In this method, the inclination of holes is one of the sources of error. This paper presents a finite element analysis of the influence of inclined holes on the uniaxial residual stress field. The error in stress has been found to increase proportionally to the correct inclined angle of the hole. The correction equations by which one may easily obtain the residual stress, taking account of the inclined angle and direction, have been derived. The error of stress due to the inclined hole has been reduced to around 1% using the correction equations.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.11
• /
• pp.900-908
• /
• 2009

Numerical simulation has been carried out to investigate the influence of radial temperature gradient on the Taylor Vortex flow. Varying the Grashof number, we study the detailed flow and temperature fields. The current numerical results show good agreement with the experimental results currently available. It turns out that wavy spiral vortices are generated by increasing temperature gradient. We classify flow patterns for various Grashof numbers based on the characteristics of flow fields and spiral vortices. The correlation between Grashof number with wave number shows that the spiral angle and size of Taylor vortices increase with increasing temperature gradient. Temperature gradient does not have a great influence on the heat transfer rate of the cylinder surfaces.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.39-43
• /
• 2008

Atmospheric pressure plasma polishing (APPP) is a noncontact precision machining technology that uses low temperature plasma chemical reactions to perform atom-scale material removal. APPP is a complicated process, which is affected by many factors. Through a preliminary theoretical analysis and simulation, we confirmed that some of the key factors are the radio frequency (RF) power, the working distance, and the gas ratio. We studied the influence of the RF power and gas ratio on the removal rate using atomic emission spectroscopy, and determined the removal profiles in actual operation using a commercial form talysurf. The experimental results agreed closely with the theoretical simulations and confirmed the effect of the working distance. Finally, we determined the element compositions of the machined surfaces under different gas ratios using X-ray photoelectron spectroscopy to study the influence of the gas ratio in more detail. We achieved a surface roughness of Ra 0.6 nm on silicon wafers with a peak removal rate of approximately 32 $mm^{3}$/min.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.6
• /
• pp.201-206
• /
• 2001

The hole-drilling method makes a little hole through the metal surface that has residual stress and measures the relieved stress with a strain gage. It is used widely in measuring the residual stress of surfaces. In this method, the inclined hole is one of the source of error. This paper presents a finite element analysis of influence of the inclined hole for the uniaxial residual stress field. The stress differences between measured and applied residual stress increase proportionally to inclined angle of the hole. The correction equations which easily obtain the residual stress taking account of the inclined angle and direction are derived. The measurement error of stress due to the inclined hole can be reduced to around 1% through this study.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.349-356
• /
• 1998

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and tower structures, with irregular cross sections and with arbitrary boundary conditions was developed and reported by Kim, D. H. in 1974. In this paper, the result of application of this method to the three span continuous reinforced concrete bridge with elastic intermediate supports in presented. Such bridge represents either concrete or sandwich type three span bridge on polymeric supports for passive control or on actuators for active control. Any method may be used to obtain the deflection influence surfaces needed for this vibration analysis. Finite difference method is used for this purpose, In this paper. The influence of the modulus of the foundation and $D_{22}$, $D_{l2}$, $D_{66}$ stiffnesses on the natural frequency is thoroughly studied.d.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1998.04a
• /
• pp.341-348
• /
• 1998

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and tower structures, with irregular cross sections and with arbitrary boundary conditions was developed and reported by Kim, D. H. in 1974. In this paper, the result of application of this method to the subject problem is presented. The structure considered for this report is two span continuous special orthotropic plates with elastic intermediate support. The use of elastic support as one of the passive control means is common. Any method may be used to obtain the deflection influence surfaces needed for this vibration analysis. Finite difference method is used for this purposa in this paper. The influence of the modulus of the foundation, and $D_{ij}$ stiffnesses on the natural frequency is thoroughly studied.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.10a
• /
• pp.215-222
• /
• 1997

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and tower structures, with irregular cross-sections and with arbitrary boundary conditions was developed and reported by D. H. Kim in 1974. This method has been developed for two-dimensional problems including the laminated composite plates and was proved to be very effective for the plates with arbitrary boundary conditions and irregular sections. In this paper, the result of application of this method to the subject problem is presented. This problem represents the building slabs with a kind of passive and active control devices. Any method may be used to obtain the deflection influence surfaces needed for this vibration analysis. Finite difference method is used for this purpose, in this paper. The influence of the modulus of the foundation on the natural frequency is thoroughly studied.