• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.265-274
• /
• 1994

Intermetallic Ti-Si system ceramics were synthesized from stochiometric mixtures of titanium and silicone powders in vacuum by Self-propagating High-temperature Synthesis(SHS). In each cases of Ti5Si3, Ti5Si4 and TiSi, and TiSi2 synthesis, 20wt% product dilution, direct ignition and SHS chemical furnace method were employed. The combustion modes, which were observed during the synthesis process by using the high speed camera, of Ti5Si3, Ti5Si4, TiSi, and TiSi2 exhibit spin, osciallatory, steady-state, and spin combustion, respectively. With increasing Ti/Si molar ratio an decrease of combustion velocities was found. From the results on the measurement of the flexural strength, the specimen hot pressed at 135$0^{\circ}C$ for 30 min using synthesized Ti5Si4 powders showed the highest flexural strength at 215 MPa.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.1
• /
• pp.69-78
• /
• 2001

This paper presents the design and FPGA implementation of a FLEX PSP(Protocol Signal Processor) for the portable high speed paging system. In this approach, two algorithms are newly proposed for implementing the PSP which provides capabilities of the maximum 6,400bps at speed, high-channel throughput, real time error correction and an effective frame search function. One is an accurate symbol synchronization algorithm which is applied for synchronizing the interleaved 4-level bit symbols which are received at input stage of A/D converter, and the other is a modified fast decoding algorithm which is provided for realizing double error correction of (31,21)BCH signal. The PSP is composed of six functional modules, and each module is modelled in VHDL(VHSIC Hardware Description Language). Both functional simulation and logic synthesis have performed for the proposed PSP through the use of Synopsys$^{TM}$ tools on a Axil-320 Workstation, and where Altera 10K libraries are used for logic synthesis. From logic synthesis, we can see that the number of gates is about 2,631. For FPGA implementation, timing simulation is performed by using Altera MAX+ PLUS II, and its results will be also given. The PSP which is implemented in 6 FPGA devices on a PCB has been verified by means of Logic Analyzer.r.

• Archives of Metallurgy and Materials
• /
• v.66 no.4
• /
• pp.987-990
• /
• 2021

As the amount of high-capacity secondary battery waste gradually increased, waste secondary batteries for industry (high-speed train & HEV) were recycled and materialization studies were carried out. The precipitation experiment was carried out with various conditions in the synthesis of LiNi_0.6Co_0.2Mn_0.2O₂ material using a Taylor reactor. The raw material used in this study was a leaching solution generated from waste nickel-based batteries. The nickel-cobalt-manganese (NCM) precursor was prepared by the Taylor reaction process. Material analysis indicated that spherical powder was formed, and the particle size of the precursor was decreased as the reaction speed was increased during the preparation of the NCM. The spherical NCM powder having a particle size of 10 ㎛ was synthesized using reaction conditions, stirring speed of 1000 rpm for 24 hours. The NCM precursor prepared by the Taylor reaction was synthesized as a cathode material for the LIB, and then a coin-cell was manufactured to perform the capacity evaluation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.2
• /
• pp.402-407
• /
• 2005

The PLL synthesizer is used in communication system until now because it have several merits, such as broad bandwidth, high accuracy and stability of frequency But it is difficult to use in the third generation mobile communication systems that need frequency hopping at a high speed because of its long frequency hopping time. In this paper, we designed the frequency synthesizer that generate frequencies randomly at a high speed using the DDS technology.

• Metals and materials international
• /
• v.24 no.6
• /
• pp.1327-1332
• /
• 2018

In this study, a novel approach to the explosive synthesis of titanium carbide (TiC) is discussed. Nonstoichiometric $TiC_x$ powder was produced via the underwater explosion of a Ti powder encapsulated within a spherical explosive charge. The explosion process, bubble formation, and synthesis process were visualized using high-speed camera imaging. It was concluded that synthesis occurred within the detonation gas during the first expansion/contraction cycle of the bubble, which was accompanied by a strong emission of light. The recovered powders were studied using scanning electron microscopy and X-ray diffraction. Submicron particles were generated during the explosion. An increase in the carbon content of the starting powder resulted in an increase in the carbon content of the final product. No oxide byproducts were observed within the recovered powders.

• Journal of the Korean Ceramic Society
• /
• v.44 no.11
• /
• pp.597-606
• /
• 2007

With the advent of ubiquitous age, the high quality dielectric materials have been required for the wireless communications available to the millimeterwave as well as microwave frequencies. The utilizable region for the frequency has been expanding to the millimeter-wave region because of the shortage of radio frequency (RF) resources. These high frequencies would be expected for ultra high speed LAN, ETS and car anti-collision system on the intelligent transport system (ITS) and so on. Silicates are good candidates for microwave/millimeterwave dielectrics, because of their low dielectric constant ${\epsilon}_r$ and high quality factor (High Q). Forsterite ($Mg_2SiO_4$) is one of the silicates with low ${\epsilon}_r$ of 6.8 and Q f of 240000 GHz. In this paper, we reviewed following three categories for synthesis of forsterite: (1) Synthesis of high Q forsterite (2) Adjust the temperature coefficient of resonant frequency $TC_f$ (3) Diffusion of $SiO_{4^-}$ and Mg-ions on the formation of forsterite.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.238-241
• /
• 2000

This paper describes an equalizer using the DFE (Decision Feedback Equalizer) structure, CMA. (Constant Modulus Algorithm) and LMS (Least Mean Square) algorithms. We employ high speed multipliers, square logics and many CSAs (Carry Save Adder) for high speed operations. We have developed floating-point models and fixed-point models using the COSSAP$\^$TM/ CAD tool and developed VHDL models. We have peformed logic synthesis using the SYNOPSYS$\^$TM/ CAD tool and the SAMSUNG 0.5 $\mu\textrm{m}$ standard cell library (STD80). The total number of gates is about 130,000.

• ETRI Journal
• /
• v.39 no.4
• /
• pp.493-501
• /
• 2017

This paper introduces a new motion-synthesis technique for animating multiple characters. At a high level, we introduce a hub-sub-control-point scheme that automatically generates many different spline curves from a user scribble. Then, each spline curve becomes a trajectory along which a 3D character moves. Based on the given curves, our algorithm synthesizes motions using a cyclic motion. In this process, space-time warp curves, which are time-warp curves, are embedded in the 3D environment to control the speed of the motions. Since the space-time warp curve represents a trajectory over the time domain, it enables us to verify whether the trajectory causes any collisions between characters by simply checking whether two space-time warp curves intersect. In addition, it is possible to edit space-time warp curves at run time to change the speed of the characters. We use several experiments to demonstrate that the proposed algorithm can efficiently synthesize a group of character motions. Our method creates collision-avoiding trajectories ten times faster than those created manually.

• Journal of Sensor Science and Technology
• /
• v.21 no.5
• /
• pp.385-388
• /
• 2012

This paper describes the synthesis and characterization of graphene by RTA process. Amorphous 3C-SiC were deposited using APCVD for carbon source and Ni layer were employed for transition layer. Various parameters of the ramping speed, the annealing time and the cooling speed are evaluated for the optimized combination allowed for the reproducible fabrication of graphene using 3C-SiC thin film. For analysis of crystalline Raman spectra was employed. Transferred graphene shows a high IG/ID ratio of 2.73. SEM and TEM images show the optical transparency and 6 carbon network, respectively. Au electrode deposited on the transferred graphene shows linear I-V curve and its resistance is 358 ${\Omega}$.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.4
• /
• pp.1299-1304
• /
• 2000

In a speed coding system using excitation source of voiced and unvoiced, it would be involved a distortion of speech quality in case coexist with a voiced and an unvoiced consonants in a frame. So, I propose TSIUVC(Transition Segment Including UnVoiced Consonant) searching, extraction ad approximation-synthesis method in order to uncoexistent with a voiced and unvoiced consonants in a frame. This method based on a zerocrossing rate and pitch detector using FIR-STREAK Digital Filter. As a result, the extraction rates of TSIUVC are 84.8% (plosive), 94.9%(fricative), 92.3%(affricative) in female voice, and 88%(plosive), 94.9%(fricative), 92.3%(affricative) in male voice respectively, Also, I obain a high quality approximation-synthesis waveforms within TSIUVC by using frequency information of 0.547kHz below and 2.813kHz above. This method has the capability of being applied to speech coding of low bit rate, speech analysis and speech synthesis.