• Journal of Biosystems Engineering
• /
• 제4권2호
• /
• pp.65-83
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well. 2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air. 3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying. 4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis. 5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time. 6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture. 7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation. 8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise. 11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss. 12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method. 13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated. Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year. 14. Required fan horsepower and energy for the intermittent fan operation were 3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation. 15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use. 16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• Journal of Biosystems Engineering
• /
• 제4권2호
• /
• pp.64-64
• /
• 1979

Low-temperature drying systems have been extensively used for drying cereal grain such as shelled corn and wheat. Since the 1973 energy crisis, many researches have been conducted to apply solar energy as supplemental heat to natural air drying systems. However, little research on rough rice drying has been done in this area, especially very little in Korea. In designing a solar drying system, quality loss, airflow requirements, temperature rise of drying air, fan power and energy requirements should be throughly studied. The factors affecting solar drying systems are airflow rate, initial moisture content, the amount of heat added to drying air, fan operation method and the weather conditions. The major objectives of this study were to analyze the effects of the performance factors and determine design parameters such as airflow requirements, optimum bed depth, optimum temperature rise of drying air, fan operation method and collector size. Three hourly observations based on the 4-year weather data in Chuncheon area were used to simulate rough rice drying. The results can be summarized as follows: 1. The results of the statistical analysis indicated that the experimental and predicted values of the temperature rise of the air passing through the collector agreed well.2. Equilibrium moisture content was affected a little by airflow rate, but affected mainly by the amount of heat added, to drying air. Equilibrium moisture content ranged from 12.2 to 13.2 percent wet basis for the continuous fan operation, from 10.4 to 11.7 percent wet basis for the intermittent fan operation respectively, in range of 1. 6 to 5. 9 degrees Centigrade average temperature rise of drying air.3. Average moisture content when top layer was dried to 15 percent wet basis ranged from 13.1 to 13.9 percent wet basis for the continuous fan operation, from 11.9 to 13.4 percent wet basis for the intermittent fan operation respectively, in the range of 1.6 to 5.9 degrees Centigrade average temperature rise of drying air and 18 to 24 percent wet basis initial moisture content. The results indicated that grain was overdried with the intermittent fan operation in any range of temperature rise of drying air. Therefore, the continuous fan operation is usually more effective than the intermittent fan operation considering the overdrying.4. For the continuous fan operation, the average temperature rise of drying air may be limited to 2.2 to 3. 3 degrees Centigrade considering safe storage moisture level of 13.5 to 14 perceut wet basis.5. Required drying time decrease ranged from 40 to 50 percent each time the airflow rate was doubled and from 3.9 to 4.3 percent approximately for each one degrees Centigrade in average temperature rise of drying air regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on required drying time.6. Required drying time increase ranged from 18 to 30 percent approximately for each 2 percent increase in initial moisture content regardless of the fan operation methods, in the range of 18 to 24 percent moisture.7. The intermittent fan operation showed about 36 to 42 percent decrease in required drying time as compared with the continuous fan operation.8. Drymatter loss decrease ranged from 34 to 46 percent each time the airflow rate was doubled and from 2 to 3 percent approximately for each one degrees Centigrade in average temperature rise of drying air, regardless of the fan operation methods. Therefore, the average temperature rise of drying air had a little effect on drymatter loss. 9. Drymatter loss increase ranged from 50 to 78 percent approximately for each 2 percent increase in initial moisture content, in the range of 18 to 24 percent moisture. 10. The intermittent fan operation: showed about 40 to 50 percent increase in drymatter loss as compared with the continuous fan operation and the increasing rate was higher at high level of initial moisture and average temperature rise.11. Year-to-year weather conditions had a little effect on required drying time and drymatter loss.12. The equations for estimating time required to dry top layer to 16 and 1536 wet basis and drymatter loss were derived as functions of the performance factors. by the least square method.13. Minimum airflow rates based on 0.5 percent drymatter loss were estimated.Minimum airflow rates for the intermittent fan operation were approximately 1.5 to 1.8 times as much as compared with the continuous fan operation, but a few differences among year-to-year.14. Required fan horsepower and energy for the intermittent fan operation were3. 7 and 1. 5 times respectively as much as compared with the continuous fan operation.15. The continuous fan operation may be more effective than the intermittent fan operation considering overdrying, fan horsepower requirements, and energy use.16. A method for estimating the required collection area of flat-plate solar collector using average temperature rise and airflow rate was presented.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.23-28
• /
• 2010

Of the roughly four million known substances, about 60,000 are processed and sold ; many of these must be dried. Many materials are processed in the liquid state - ideal for mixing and reacting - but most products are needed or wanted as dry, or relatively dry, solids. Usually operation is just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressures as low as 26.66kPa abs.. In spite of the global-class aquiculture agriculture and fisheries technology of our country, the processing technologies are lags behind the other nations relatively. These problems are considered to be caused directly by the lack of drying technologies. This paper is concerned to the experimental results of drying heat transfer characteristics for the green energy type vacuum dryer for the high quality agriculture and fisheries production.

• 한국잠사곤충학회지
• /
• 제13권2호
• /
• pp.155-160
• /
• 1971

본 시험은 우리나라의 원료견질에 적합한 자동조사기의 기술체계를 확립하기 위한 연구로서 다음 결과를 얻었다. 1) 원료견 성상에 따른 생사량 및 조사능률을 감안한 합리적인 조사속도는 해서량호견(해서사장 850m)은 150m/min 내외, 해서중용견(해서사장 650m)은 120m/min 내외, 해서하량견(해서사장 500m)은 90~120m/min 이었다. 2) 건견온도별에 있어서 저온구(T$_3$)는 표준구(T$_1$) 및 고온구(T$_2$)에 비하여 해서율은 향상되나 사조고장은 증가하고 생사품위가 저하되었으며 생사량비율 및 부잠사양비율에 있어서는 유의차를 인정할 수 없었다. 3) 건견정도별에 있어서는 약건구(T$_3$)는 표준구(T$_1$) 및 과건구(T$_2$)에 비하여 해서율은 향상되었으나 사조고장이 증가하고 생사품위가 저하되었으며 생사량비율 및 부잠사량비율에 있어서는 유의차를 인정할 수 없었다. 따라서 자동조사의 합리적인 건견조건으로는 건견온도에 있어서 저온건견을 피하여 표준건견 내지 고온건견으로 하고 건견정도에 있어서는 약건을 피하여 표준건견내지 과건하는 방향으로 건조하는 것이 생사품위를 향상시키는데 적합하다고 사료된다. 4) 자동조사의 적합한 자견정도는 적자, 조사탕온도 4$0^{\circ}C$ 또는 약자, 조사탕온도 45$^{\circ}C$로 조절하여 주는것이 좋았다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1994년도 SIEMSTA94 농업과학 기계기술 심포지엄
• /
• pp.139-160
• /
• 1994

The-state-of-the-art of rice drying in the U.S.A. is presented. The U.S.A. is a minor producer but major exporter of rice. Head yield is its major criterion in evaluating rice quality . A decrease of 1 to 3 points in head yield can be expected to occur in a well-designed rice-drying system. Rice is dried on the farm in bins in the U.S. A., and n high-temperature continuous -flow dryers at the elevator level. Two relatively new rice-drying systems are discussed in some detail. : The top-bin/in -bin-counterflow bin-type on-farm dryer, and the concurrent-flow high-temperature elevator dryer.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.19-29
• /
• 2006

Drying is the least developed of all unit operations of paper and board manufacture. While groundbreaking developments were Introduced during the several past decades in forming, pressing and calendering, no radical changes occurred in drying. The cylinder-drying technology is now more than 200 years old and, while it was subject to many incremental improvements, many of its inherent problems persist. We believe that conventional drying is now approaching the end of its life and the industry is ready for a major breakthrough in drying. Indeed several innovative technologies already exist at various stages of development or commercialization. In general, the novel drying technologies are striving to increase the drying rate, improve the product quality and boost the energy efficiency of drying. A novel, drying method, $Papridry^{TM}$, which combines conductive and convective heat transfer to obtain very high drying rates, is at an advanced stage of development at Paprican. The results obtained when drying printing paper ana board on a self-standing pilot $Papridry^{TM}$ machine and on the pilot paper machine equipped with a tandem of two $Papridry^{TM}$ units demonstrate both, the high drying rate and improved product quality achieved by using this drying method. A mathematical model of this operation has been developed and the software compiled with this model was used to calculate the effect of installing a $Papridry^{TM}$ unit into an existing dryer section. The model also allows to calculate the z-direction distribution of moisture and temperature at various points of the dryer section.

• 농업과학연구
• /
• 제42권4호
• /
• pp.439-446
• /
• 2015

Kimbugak is one of Korea's traditional snacks made of laver. This study was conducted to investigate the physical drying and frying characteristics of kimbugaks made by a pasting & garnishing machine. The drying and frying characteristics should be analyzed to develop a continuous operation system for manufacturing kimbugak because kimbugak has a high moisture content after pasting process. Materials for pasting and garnishing on laver were rice gruel and sesame. The aluminum shelf with square hole was selected as a drying shelf. The recommended size of the square hole type was $1.5mm{\times}1.5mm$ because characteristics of deformation and easy separation from the shelf were excellent at the hole size. The drying time of 2 hours was also recommended with the drying temperature of $70^{\circ}C$ based on the test results such as dried condition (good), moisture conten t (3.7%), deformation (12.1 mm), and shrinkage rate (19.8%). As the frying conditions for dried kimbugaks, recommended oil temperature and frying time were $170^{\circ}C$, 15 seconds, respectively when corn oil was used. In the case of frying for undried kimbugaks, recommended oil temperature and frying time were $210^{\circ}C$, 2 - 3 minutes, respectively for improvement of work efficiency.

• Journal of the Korean Wood Science and Technology
• /
• 제46권3호
• /
• pp.213-220
• /
• 2018

리기다소나무를 구조용 집성재의 재료로 이용하기 위해 판면의 옹이와 대패가공 후 방치시간에 따른 수지 삼출량이 레조르시놀수지로 접착한 판재의 접착성능에 미치는 영향을 검토하였다. 고온($120{\sim}95^{\circ}C$) 및 저온($65{\sim}50^{\circ}C$)에서 건조한 리기다소나무의 수지 삼출량은 판목면이 정목면 보다 저온건조재가 고온건조재보다 많았다. 방치시간별로는 저온건조재는 3일째 고온건조재는 7일째에 최고함량을 보였고, 이후부터는 서서히 감소하여 15~90일에는 거의 차이가 없었다. 접착성능은 수지의 삼출이 많은 2~3일까지는 낮았으나 15일 이후에는 큰 차이가 없었으며, 고온 및 저온 건조재 모두 방치시간에 관계없이 KS 기준의 접착성능을 만족하였다. 옹이부가 포함된 적층 구성에서의 접착강도는 KS의 접착강도 기준 이상이었으나 목파율은 기준인 65% 이상을 만족하지 못하였다. 적층 단면구성(정목+정목, 판목+판목, 정목+판목)에 따른 접착성능은 고온 및 저온건조재 모두 모든 적층구성에서 KS의 기준을 크게 상회하였다.

• 한국축산식품학회지
• /
• 제35권5호
• /
• pp.597-603
• /
• 2015

The purpose of this study was to investigate the influence of processing conditions (temperature and time) and binding agent types (glutinous rice flour, potato starch, bean flour, and acorn flour) on the physicochemical and sensory characteristics of ground dried-pork meat product. For this purpose, ground dried-pork meat product was produced by adding several binding agents at different drying temperatures and times. The drying time affected moisture content and water activity in all drying temperature. However, under the similar drying conditions, the extent of drying varied depending on the type of binding agents. The results of sensory evaluation for texture degree and overall acceptability indicated the following: overall, higher drying temperatures and longer drying time heightened the degree of texture, and the overall acceptability varied depending on binding agent type. Physicochemical and sensory characteristics were analyzed to determine any possible correlation. The results revealed a high correlation between moisture content, water activity, shear forces, and sensory evaluation (p<0.01). However, there was no correlation with respect to overall acceptability.

• 한국식품과학회지
• /
• 제21권3호
• /
• pp.425-429
• /
• 1989

고추의 건조 중 중요한 품질요소인 carotenoid 파괴 및 비효소적 갈변의 kinetics를 건조 중 품질측정을 이용한 dynamic test에 의하여 평균 수분함량과 온도의 함수관계를 결정하였다. 1차반응으로 가정된 carotenoid 파괴 속도상수는 고온 고수분에서 높았으며 수분의존성에 있어서 건조중간의 어떤 수분함량에서 최소치를 보여주고 있었다. 온도의존성에 있어서 활성화 에너지는 7.7-27.4kcal/mol로 나타났고 수분함량이 높을수록 높았다. 0차반응으로 분석된 비호소적 갈변은 온도와 수분함량이 높을수록 쉽게 일어났으며 활성화에너지는 7.5-20.2kcal/mol로서 수분함량이 높을수록 높았다.