• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.725-728
• /
• 1999

The bridge slab of express railway was designed for high strength concrete (design strength 400kgf/$\textrm{cm}^2$). In case the slab is made with the concrete using type I cement, used much amount of cement can cause cracks through concrete by hydration heat or dry shrinkage. In this study we targeted to solve above problems using type III cement. We could decrease the cement ratio in concrete using type III cement than type I cement. The concrete using type III cement showed good workability and compressive strength, and showed better properties in hydration heat and dry shrinkage than that using type I cement

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.197-198
• /
• 2018

As part of the effort to shorten the construction period, this study examined the strength expression characteristics at the early age of concrete using high fineness cement and blast furnace slag. accordingly to provide a basic data on how to solve the problem that the initial strength is lowered.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.100-101
• /
• 2020

In this study, the temperature history and compressive strength of the concretes according to the type of cement were measured and analyzed in comparison as part of the experiment on the material mixing side to reduce the hydration heat crack of the mat foundation constructed with mass concrete. As a result, the peak temperature and maximum temperature reach time of concrete using high rapid cement were shown to be similar to that of semi rapid cement. In particular, in compressive strength after three days, semi rapid cement was measured higher than that of concrete using high rapid cement. Therefore, if semi rapid cement is used in accordance with the site conditions, it is deemed possible to shorten the air due to reduction of temperature cracks and improvement of initial strength.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.126-129
• /
• 2000

To investigate the influence of kinds of cement on state of high-strength concrete, this study deals with the engineering properties of high-strength concrete used 4 kinds of ordinary portland cement. The result of this study be summarized as follows. 1) It appeared that the change in fluidity with time differ with kinds of cement. 2) The difference of setting time was seen over 3 hours according to kinds of cement. Therefore, it must be examined about used materials when high-strength concrete is manufactured in the construction field.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.247-250
• /
• 2000

As construction technology advances, most of concrete structures are becoming larger and taller. Therefore, high strength and high quality concrete is necessary for them. Nowadays, the proposal of using type IV(belite cement) is investigated to satisfy high flowing, low heat, and ho호 strength. In this study, the flow value and compressive strength of mortar were investigated according to usage of AE high range water reducer. And the slump flow value, falling time and heigth difference of concrete with beilte cement and ordinary cement were examined depending on water cement ratio, sand ratio and unit water weigth, and compressive strength to checked depending on age.

• Geomechanics and Engineering
• /
• v.7 no.3
• /
• pp.247-261
• /
• 2014

Analytical and numerical modeling of soft or problematic soils stabilized with lime and cement require a number of soil parameters which are usually obtained from expensive and time-consuming laboratory experiments. The high shear strength of lime and cement stabilized soils make it extremely difficult to obtain high quality laboratory data in some cases. In this study, an alternative method is proposed, which uses the unconfined compressive strength and estimating functions available in literature to evaluate the shear strength parameters of the treated materials. The estimated properties were applied in finite element model to determine which estimating function is more appropriate for lime and cement treated granular soils. The results show that at the mid-range strength of the stabilized soils, most of applied functions have a good compatibility with laboratory conditions. However, application of some functions at lower or higher strengths would lead to underestimation or overestimation of the unconfined compressive strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.04a
• /
• pp.71-74
• /
• 2007

This study investigates the fundamental properties of high strength concrete made with various blame values of cement, manufactured by the particle screening method in a pulverizing process. Test showed that concrete using lower blame of cement, such as large particle (L) and both ordinary and large particle (OL), increased the fluidity of fresh concrete. As tine progressive, it was noticeable that the specimens using ordinary cement (OPC) gradually decreased the fluidity, but the other specimens showed the sudden decline until 30 minutes, which is followed by a gradual decrease after 60 minutes. For the setting time, higher blaine of cement accelerated the initial and final setting time, especially concrete using minute size of cement (M) was 10 hours faster than OPC. Compressive strength of L exhibited similar value at 1 days as to that of strength in OPC at 3 days. Importantly, the specimens using M also revealed the similar strength value, regardless of curing temperature between $-5^{\circ}C$ and $20^{\circ}C$, which means that using this minute particle of cement in concrete can secure the strength development even in the lower temperature circumstance. Therefore it is clear that using OPC+M simultaneously at cold weather concreting can resist the early frost and develop the early strength of concrete.

• Journal of the Korean Ceramic Society
• /
• v.47 no.5
• /
• pp.357-364
• /
• 2010

This study was performed to get basic information about properties of high blaine slag cement(HSC) to use shotcrete(or sprayed concrete and mortar). Particle size distribution, setting time and compressive strength test, analysis like as SEM, DSC thermal analysis, XRD was carried out to investigate principle properties of HSC. Setting time of HSC was delayed slightly, but influence of accelerators was more bigger than ordinary portland cement(OPC). Compressive strength of HSC at 28 days was more higher than OPC regardless of using accelerators. Results of analysis showed early period hydration products of HSC is more small and located widely, because of the interface of between cement particle and water is increased as specific surface of cement increase. From the SEM observation and analysis of DSC and XRD results, aluminates accelerators bring on some hydration products like as calcium aluminium hydrates, alkali free accelerators increases ettringite and monosulfates. Aluminates accelerators has a advantage of setting time and early strength, alkali free accelerators increases strength after 7 days.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.583-586
• /
• 2005

Strength of concrete is very important factor in design and quality management and may represent overall quality of concrete. Such strength of concrete may differ depending on amount of cement mixed, water and fine aggregate ratio. Classic concrete products have been produced mainly with ordinary portland cement(hereinafter 'cement'), water and fine aggregate as shown above, but various additives and mixture materials have been used for concrete manufacturing, along with development of high functional concrete and diversification of structures. Various kinds of chemical mixtures agents and mixture materials have been used as it requires concretes with other features which cannot be solved with existing materials only, such as high strength, high flexibility and no-separation in the water. Such addition of various mixture agents may cause change in cement hydrate, affecting strength. Hydration of cement is the process of producing potassium hydroxide, C-S-H, C-A-H and Ettringite, while causing heat generation reaction after it is mixed with water, and generation amounts of such hydrates play lots of roles in condensation and hardening. This study aims to analyze its strength and features with hydrates by making specimen according to curing temperature, types of mixture agent, mixing ratio and ages and by analyzing such hydrates in order to analyze role of cement hydrate on early strength of concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.72-77
• /
• 1995

Blast-furnace slag cement has been used widely as a structural material due to the latent hydraulicity of granulated ground blast furnace slag(GGBS)for a long time as The wall as ordinary portland cement. In this study, based on the fundamental investigation on the high strength and high durable concrete using the high fineness GGBS the following remarks can be made. 1) The average desired strenth of concrete is Or=600~800kg/$\textrm{cm}^2$. 2) The above high strength concrete using the high fineness GGBS is more workable than those using only OPC. 3) The adiabatic temperature and drying shringkage decrease, so the density and resistance to sea water attack increase as results. 4)The unit cement content and unit air entrained admixture at the same desired strength of concrete decrease, so the economical high strength concrete can be manufactured from using the high fineness GGBS.