• 한국해양공학회지
• /
• 제15권2호
• /
• pp.105-110
• /
• 2001

The fatigue crack propagation behavior of the SA516/70 steel which is used for pressure vessels was examined experimentally at room temperature, 150$^{\circ}C $, 250$^{\circ}C $ and 370$^{\circ}C $ with stress ratio of R=0.1 and 0.3. The fatigue crack propagation rate da/dN related with the stress intensity factor range $\Delta K$ was influenced by the stress ratio within the stable growth of fatigue crack(Region II) with an increase in $\Delta K$. The resistance to the fatigue crack growth at high temperature is higher in comparison with that at room temperature, and the resistance attributed to the extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and high temperature are mainly explained by the crack closure and oxide-induced by high temperature.

• 한국해양공학회지
• /
• 제2권2호
• /
• pp.104-111
• /
• 1988

This paper deals with the micro-surface-cracks behavior on the unnotched smooth specimens of Type 304 stainless steel at $593^{\circ}C$ in air under creep and creep-fatigue conditions that have 10 mim and 1 min load holding times respectively. The behaviors of the micro-surface-cracks have been visualized by means of surface replica method and optical micro-photography. The quantitative characteristics of initiation, growth and coalescence of micro-surface-cracks have been investigated by observing and measuring the crack growth behaviors. some of the important results are as follows: Main crack initiates at grain boundary in the early stage(10 to 20%)of its life time and grows through coalescence and finally leads to fracture. The distribution of micro-surface-crack length, 2a, can be plotted against the composite Weibull distribution. The growth rate of the main crack can be plotted against the stress intensity factor, crack tip opering displacement and J integral.

• 대한기계학회논문집
• /
• 제13권4호
• /
• pp.670-679
• /
• 1989

본 연구에서는 항공기 구조용 재료로서 널리 사용되는 국산 고장력 7075-T73 알류미늄 합금을 준비하고 일정진폭하중 및 단일과대하중에 의한 피로균열 진전거동에 미치는 두께의 영향과 이의 기구를 검토하였다.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1097-1103
• /
• 1988

본 연구에서는 이 좁은 벤트내에 자료가 모이는 피로균열의 특성을 이용하여 표면피로균열의 성장거동을 파괴역학적으로 해석, 연구하여 균열의 성장특성과 $S-N_{f}$ 곡선의 추정을 마이크로 컴퓨터로 계산하였다.

• 열처리공학회지
• /
• 제18권4호
• /
• pp.229-234
• /
• 2005

Effect of incident ion beam energy on microstructure and adhesion behavior of TiN thin films were studied. Without ion beam assist, TiN film showed (111) growth mode which was thought to have the lowest deformation energy. As the ion beam assist energy increased, TiN film growth mode was changed from (111) to (200) mode. On the Si(100) substrate the critical incident energy for growth mode change was 100 eV/atom, however the critical assist energy was 121 eV/atom on the STD61 substrate. Grain size of TiN films increased with the assist ion beam energy. Finally, adhesion strength of TiN films bombarded above the critical ion assist energy showed 4~5 times higher values than that with lower bombard ion energy.

• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.2977-2981
• /
• 2021

Corrosion fatigue crack growth (FCG) behavior of 316LN stainless steel was investigated in high-temperature pressurized water at different temperatures, load ratios (R = K_max/K_min) and rise times (t_R). The environmental assisted effect on FCG rate was observed when both the R and t_R exceeded their critical values. The FCG rate showed a linear relation with stress intensity factor range (ΔK) in double logarithmic coordinate. The environmental assisted effect on FCG rate depended on the ΔK and quantitative relations were proposed. Possible mechanisms of environmental assisted FCG rate under different testing conditions are also discussed.

• Nuclear Engineering and Technology
• /
• 제53권7호
• /
• pp.2304-2311
• /
• 2021

The dislocation density in strain-hardened Alloy 690 was analyzed using scanning transmission electron microscopy (STEM) to study the relationship between the local plastic strain and susceptibility to primary water stress corrosion cracking (PWSCC) in nuclear power plants. The test material was cold-rolled at various thickness reduction ratios from 10% to 40% to simulate the strain-hardening condition of plant components. The dislocation densities were measured at grain boundaries (GB) and in grain interiors of strain-hardened specimens from STEM images. The dislocation density in the grain interior monotonically increased as the strain-hardening proceeded, while the dislocation density at the GB increased with strain-hardening up to 20% but slightly decreases upon further deformation to 40%. The decreased dislocation density at the GB was attributed to the formation of deformation twins. After the PWSCC growth test of strain-hardened Alloy 690, the fraction of intergranular (IG) fracture was obtained from fractography. In contrast to the change in the dislocation density with strain-hardening, the fraction of IG fracture increased remarkably when strain-hardened over 20%. From the results, it was suggested that the PWSCC growth behavior of strain-hardened Alloy 690 not only depends on the dislocation density, but also on the microstructural defects at the GB.

• Structural Engineering and Mechanics
• /
• 제81권1호
• /
• pp.39-50
• /
• 2022

Layer separation (delamination) is an essential threat to fiber-reinforced polymer (FRP) plates under dynamic, static, and fatigue loads. Under compressive load, the growth of delamination will lead to structural instability. The aim of this paper is to present a method using shape memory alloy (SMA) stitches to suppress the delamination growth in a FRP plate and to improve the buckling behavior of the plate with a rectangular hole. The present paper is divided into two parts. Firstly, a closed-form (CF) formulation for evaluating the buckling load of the FRP plate is presented. Secondly, the finite element method (FEM) will be employed to calculate the buckling loads of the plates which serves to validate the results obtained from the closed-form method. The novelty of this work is the development of the closed-form solution using the p-Ritz energy approach regarding the stress-dependent phase transformation of SMA to trace the equilibrium path. For the FEM, the Lagoudas constitutive model of the SMA material is implemented in FORTRAN programming language using a user material subroutines (VUMAT). The model is simulated in ABAQUS/Explicit solver due to the nature of the loading type. The cohesive zone model (CZM) is applied to simulate the delamination growth.

• 대한수학회보
• /
• 제61권1호
• /
• pp.161-193
• /
• 2024

In this paper, we consider the asymptotic behavior of solutions for the partly dissipative reaction diffusion systems of the FitzHugh-Nagumo type with hereditary memory and a very large class of nonlinearities, which have no restriction on the upper growth of the nonlinearity. We first prove the existence and uniqueness of weak solutions to the initial boundary value problem for the above-mentioned model. Next, we investigate the existence of a uniform attractor of this problem, where the time-dependent forcing term h ∈ L²_b(ℝ; H^-1(ℝ^N)) is the only translation bounded instead of translation compact. Finally, we prove the regularity of the uniform attractor A, i.e., A is a bounded subset of H²(ℝ^N) × H¹(ℝ^N) × L²_µ(ℝ⁺, H²(ℝ^N)). The results in this paper will extend and improve some previously obtained results, which have not been studied before in the case of non-autonomous, exponential growth nonlinearity and contain memory kernels.

• 한국산학기술학회논문지
• /
• 제15권4호
• /
• pp.2256-2264
• /
• 2014

본 연구는 교대근무 간호사의 건강증진행위, 피로 및 우울을 파악하고, 건강증진행위가 피로와 우울에 미치는 영향을 밝히기 위한 서술적 연구이다. 대상자는 경상북도 A시에 소재한 3개 종합병원에 근무하는 243명의 간호사로, 자료수집기간은 2012년 9월 19일부터 25일까지였다. 자료의 분석은 SPSS 20.0을 사용하여 descriptive statistics, t-test, Pearson's correlation coefficients, ANCOVA, 및 Stepwise multiple regression으로 분석되었다. 그 결과 교대근무 간호사의 건강증진행위 점수는 모든 항목에서 비교대근무 간호사 보다 낮았고 피로와 우울에서는 높게 나타났다. 교대근무 간호사의 피로에 영향을 미치는 건강증진행위로는 영적성장 및 스트레스 관리로 11%의 설명력을 보였고, 우울에 영향을 미치는 건강증진행위로는 신체활동 및 대인관계로 5%의 설명력을 나타내었다. 이상의 결과를 바탕으로 기관차원에서 교대근무 간호사의 근무 형태를 고려한 맞춤형 건강증진행위를 증진시킬 수 있는 방안 마련과, 피로와 우울 중재를 통한 간호 업무성과 향상을 위한 영적성장, 대인관계, 신체활동 및 스트레스관리 항목이 강화된 전문적인 건강관리 프로그램 개발을 제언하는 바이다.