• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.11a
• /
• pp.42-42
• /
• 2001

The rate of coating consolidation influences the operation of several coating methods and the final quality of the coating layer. The rate of coating consolidation is characterized with a dynamic gloss meter at short times for a thin coating layer applied to the base sheet of interest. During the coating consolidation process, the laser gloss meter response curve exhibits two critical turning points that indicate the two coating immobilization points defined by the traditional methods. Five base sheets with several different coating suspensions are characterized. A model is proposed to estimate the rate of consolidation based on physical properties of the coating suspension, the base paper, and the liquid phase of the coating. The paper properties, especially the contact angle, are found to be an important factor in determining rate of consolidation. The model predicts the correct trends for the different coating suspensions and base sheets. The test method, along the model, can be used to determine the filtercake resistance of the coating layer for a thin and rapidly formed filtercake.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.12
• /
• pp.800-805
• /
• 2017

Randomly patterned and wet chemical etching processes were used to treat anti-glare of display cover glasses. The surface and optical properties of grain size and surface morphology controlled by randomly patterned etching and wet chemical solution etching were investigated. The surface morphology and roughness of the etched samples were examined using a spectrophotometer and a portable surface roughness (Ra) measuring instrument, respectively. The gloss caused by reflection from the glass surface was measured at $60^{\circ}$ using a gloss meter. The surface of the sample etched by the doctor-blade process was more uniform than that obtained from a screen pattern etching process at gel state etching process of the first step. The surface roughness obtained from the randomly patterned etching process depended greatly on the mesh size, which in turn affected the grain size and pattern formation. The surface morphology and gloss obtained by the etching process in the second step depended primarily on the mesh size of the gel state etching process of the first step. In our experimental range, the gloss increased on decreasing the grain size at a lower mesh size for the first step process and for longer reaction times for the second step process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.9
• /
• pp.607-614
• /
• 2015

To provide the clear images from the direct light on electrical board and display devices, anti glare treatment of display cover glass is needed. In this study, the effects of surface treatment temperature, concentration, and etching solution coating thickness of the gel phase on optical elements control such as gloss, haze of reflected light and transmittance, were investigated. Cover glasses were treated at different coating thickness and additive concentration. The optical properties were examined using spectrophotometer, gloss and haze meter. The surface morphology and roughness were measured by the optical microscope and Ra measuring instrument. The etching rate and surface morphologies were dramatically affected by the concentration of acid additive in the viscous gel because of re-crystallization of components in the etching solution, hydrogel formation and coagulant after coating on glass substrate. In our experimental range, cover glass which is surface-treated with various optical properties as well as the morphology uniformity was obtained; in particular, optical properties could be controlled by etching solution coating thickness of the gel phase and the concentration of additive. The gloss was depended on the surface roughness and it showed the linear relationship between optical transmittance and haze of reflected light, respectively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.68-75
• /
• 2008

This paper investigates the correlation between surface roughness and gloss of aluminium sheet painted waterborne paint. One customer criterion of automotive quality is the as-painted appearance of the final products. Especially, the current emphasis on control of surface roughness of sanded aluminium sheet has been prompted by the automotive industry's concern with the as-painted appearance. because the influence of such characteristics on paintability, and painted appearance is important in defining outer panel requirements for automobile. This paper is dedicated primarily to the issue of painted appearance and reviews for improvement of roughness. The conclusions are obtained as follows ; 1) Painted aluminium sheet appearance is strongly affected by surface roughness of base-metal and influenced by sand paper and sanding method. 2) The painted appearance of aluminium sheets was determined and related to surface roughness parameters, combination of sand paper.

• KIEAE Journal
• /
• v.6 no.4
• /
• pp.33-39
• /
• 2006

This study aims to investigate the method to reduce the surface temperature caused by insolation. To achieve this goal, surface temperature of building is measured and the effects of exterior material's color and brilliance were checked with infrared imaging. And also, exterior material's absorptances due to outdoor surface heat transfer coefficients were measured. After surface temperature measurement of 37 specimen of 5 categories, the temperature is the highest on wood($53.62^{\circ}C$) and panel($52.05^{\circ}C$). Dryvit, stone, brick is the rating of order. For exterior material's absorptances, panel(0.883) and wood(0.868) were high and Dryvit, stone, brick follows wood and panel.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.04a
• /
• pp.80-92
• /
• 2003

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids(IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the mean of the solids differences is 0.36% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.9-18
• /
• 2021

This study was aimed to investigate the effects of hair dyeing and changes of hair quality by the application of indigo dye. Methods: Indigo dye was used after water bath. After application of the dye to healthy and bleached hair samples, they were treated with heat and remained naturally by different times. Each sample was measured before and after the application and compared for the analysis. To investigate the effects of dyeing, L⁎, a⁎, and b⁎ values and bleaching degree were measured using by color-difference meter. To understand the changes of hair quality, absorbance and gloss were measured using by tensile strength and methylene blue. Results: Upon the results of dyeing, all the samples showed the significant dyeing effects before and after the application in terms of L⁎, a⁎, and b⁎ values. With respect to the bleaching effects, it showed the greatest change on Day 1 and did not show any changes from Day 3. For the measurement of tensile strength, mean values of all the samples were increased. However, the results were not significant, statistically, demonstrating no change of hair quality. No statistically significant results were found in the samples except healthy 7L(3) sample upon the absorbance results using methylene blue. Gloss of samples was changed upon the statistical analysis results. Conclusion: Indigo dye showed the hair dyeing effects, significantly, while gloss was changed and tensile strength and absorbance were not changed in terms of hair quality. Further studies are required on the processing with a variety of dyes and on the measurements for reliability and objectivity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.39-48
• /
• 2002

The water retention of coating colors can be accurately measured by devices such as an AA-GWR water retention meter whose principle of measurement Is based on pressure filtration of coatings under an externally applied air pressure over a certain period of time. It was hypothesized that such devices could be also used to determine the immobilization solids (IMS) of coating colors by determining a sudden drop in the rate of dewatering, that is, a sudden change in the drainage curves. To test this hypothesis, the immobilization solids of coating colors containing various thickeners and water retention additives at different levels were first accurately measured by a modified immobilization tester based on the well-known gloss drop method, and then their values were compared with those obtained by an AA-GWR water retention tester. They agreed very well and showed that the standard deviation is only 0.14% in the IMS points between both methods. This good agreement was not surprising because both test methods are based on the same end-point, that is, the immobilization solids point at which menisci begin to form at the coating surface. Theoretical considerations supporting this new method for measuring the immobilization solids of coating colors are presented and some recommendations for the test method are discussed. Also, the effect of various thickeners and water retention additives on the properties and printability of coated papers is discussed.

• Korean Journal of Materials Research
• /
• v.29 no.6
• /
• pp.378-384
• /
• 2019

Ice accumulation on Aluminum Conductor Steel Reinforced(ACSR) cable during winter is an important matter in terms of safety, economy, and efficient power supply. In this work, the ice adhesion strengths of ACSR cable oxidized during different periods(7 years oxidized and 15 years oxidized) are evaluated. At first, a plate type dry oxidation standard specimen, whose surface characteristics are similar to those of ACSR cable, is prepared. Dry oxidation standard specimens are heat-treated at $500^{\circ}C$ for 20, 60, and 120 minutes in order to obtain different degrees of oxidation. After the dry oxidation, surface properties are analyzed using contact angle analyzer, atomic force microscopy, spectrophotometer, and gloss meter. The ice adhesion strengths are measured using an ice pull-off tester. Correlations between the surface properties and the ice adhesion strength are obtained through a regression analysis indicating a Boltzmann equation. It is revealed that the ice adhesion strength of 15-year oxidized ACSR cable is approximately 8 times higher than that of ACSR-bare.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.4
• /
• pp.467-472
• /
• 2009

Ultraviolet curable coating solution was prepared with poly(ethylene glycol) acrylate oligomer and various mono and multi-functional acrylate monomers. The optical properties of UV cured coating layer on PET film with acrylate coating solution containing metal oxides, such as fumed silica and alumina, were also investigated to reduce light reflection on films. Poly(ethylene glycol) diacrylate which has 575 of average molecular weight was used as oligomer acrylate, and pentaerythritol triacrylate and dipentaerythritolpenta-/hexa acrylate were used as multi-functional acrylate monomers. Also, butyl acrylate was used to improve the adhesion as well as to reduce glass transition temperature to give a better flexability. 1-hydroxy cyclohexyl phenyl ketone was used as photoinitiator. We found out the metal oxides in acrylate coating solution showed a homogeneous dispersion from energy dispersive spectroscopy data. Transmittance and light reflection of coated PET film was measured with UV/vis spectrometer and gloss meter, respectively. When 1.00 g of both metal oxides was added into coating solution, the transmittance and the glossiness were reduced from 90% to 30% and from 190 GU to 35 GU, respectively. However, adding up to 1.00 g of the metal oxide into coating solution did not affect on the hardness of coating layer and adhesion between coated layer and PET film. Conclusively, we can control transmittance and light reflection of coated film by adjusting the amounts of metal oxide in coating solution.