• 한국정밀공학회지
• /
• 제30권7호
• /
• pp.679-686
• /
• 2013

The reduction unit is one of the most important components in railway cars, due to the transmission of torque from the motor to the wheels. Faulty reduction gears in high-speed trains result from excessive wear on the gear or damage to the gear. These types of gear defects have a significant effect on high-speed rail operation and safety; thus, a diagnosis system for the reduction unit is needed. Vibration diagnosis technology is one of the most effective diagnostics. In this paper, the vibration parameters of a reduction unit were evaluated during a driving-gear test and a full-vehicle test, using kurtosis and the crest factor. These tests were performed under normal operating conditions; a specimen tester was used to diagnose problems in defective gears.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.639-645
• /
• 2011

Wheel-loader is a construction vehicle for uploading soil or sand into truck and transportation of materials, which requires large driving power and high rotational speed. To improve the working efficiency, the operator has to shift gears and control levers for bucket & boom simultaneously. Therefore, the automatic transmission has been introduced to enhance operator's convenience and enable effective operation. To develop the automatic transmission for the wheel-loader, technologies such as gears and a clutch-pack design and shift algorithm are required for improvement of shift quality. In this paper, the shift algorithm for the wheel-loader was developed and its shift pattern was analyzed. As the shift control is affected by the pressure profile for the clutch control, the shift quality depending on the pressure profile has been evaluated using experiment and simulation model analysis.

• 수산해양교육연구
• /
• 제24권2호
• /
• pp.137-145
• /
• 2012

In order to survey the conditions of bycatch and discards for a gape net, a series of filed surveys was carried out total 10 surveys on two gape nets operated in the coastal area of Jindo during July to November 2008. The all catches in each survey were measured the body length, weight after sorted species. The analysis of catch data was conducted to separate 'first operation' and 'general operation'. In this study, the first operation defined as hauling the fishing gears that soaked over 10 hours because of setting on the previous day. The general operation means the haul of fishing gears conducted at intervals of one of or two hours after first operation. The bycatch in this study is defined as the other species except for anchovy, and bycatch rate refers to the proportion of bycatch to total catch. From the survey results, the average bycatch rates on first operations were 50% and 51% for Masa-ri and Supum-ri areas in Jindo, respectively. Also, the average bycatch rates on general operation were 2% and 3% for Masa-ri and Supum-ri areas in Jindo, respectively. The proportion of anchovy to total catch caught represented 75.5%. It needs the research on the selective fishing technology to reduce the bycatch on the gape net fishery.

• 생태와환경
• /
• 제53권2호
• /
• pp.156-164
• /
• 2020

The accurate estimation of fish assemblages is highly dependent on the sampling gear used for sampling. We used data from 15 sampling sites along the Nakdong River, which is a large river in South Korea, to identify differences in assemblages and sizes of freshwater fishes collected with either cast nets or gill nets, the two most commonly used sampling gear in South Korea. The two gears differed in the fish assemblages they captured, with more species caught by gill nets. Further, due to its tighter mesh size, the cast net caught significantly smaller fishes than the gill nets(independent t-test, p<0.05). We found the cast net to be appropriate for species that inhabit shallow (less than 2 m) and open water, but inappropriate for deep water, habitats with plant beds, and nocturnal species. Thus, cast net sampling is not efficient in a large river environment, and a combination of sampling methods is more suitable for understanding fish assemblages in such habitats. In general, appropriate selection of fishing methods to specific habitats is necessary to improve data quality and minimize the misrepresentation of environmental conditions.

• 한국정밀공학회지
• /
• 제22권11호
• /
• pp.111-117
• /
• 2005

The vibration problems associated with gear coupled rotors have been the focus of much engineering work. These systems are complex and difficult to analyze in that they have the problems associated with conventional rotors plus those additional problems associated with the gear couplings. This paper examines the problems peculiar to the gear mesh. Because of the meshing action of gears, the elasticity of the gear teeth introduces time-varying stiffness coefficients into the governing equations of motion. This means that system response must be thought of in terms of Mathieu-type equations, where multiple-frequency response occur due to the periodic coefficients. The meshing action of the gears also couples the lateral and torsional gear motions. Gear errors, such as tooth profile and spacing errors, produce forces and torque that excite the system at multiple frequencies, some of which are much higher than shaft rotational speed. To investigate how to the time-varying stiffness in the gear teeth and the gear errors act one the dynamic response of the gear coupled rotors, a three-dimensional dynamic model with lateral-tortional oscillation is developed. The harmonic balance technique is employed to solve this mathieu-type problem.

• 수산해양기술연구
• /
• 제23권4호
• /
• pp.184-188
• /
• 1987

1987년 9월중에 남부해역에서 부산수산대학 실습선 402호와 403호를 이용하여 통발 어구로써 어획한 붕장어 Astroconger myriaster의 전장\ulcorner체중 및 굵기 등의 상호관계와 어체 크기와 어구망목과의 관계를 분석한 결과를 요약하면 다음과 같다. 1. 전장 L, 체중 W 및 굵기 D의 상호관계는 W=3.58$\times$10 상(-4) L 상(3.38) (r=0.99). D=0.07 L-0.59 (r=0.99). W=10.38 D 상(2.76) (r=1.00). W=1/2$\times$D 상(2)\ulcornerL 과 같이 표현된다. 2. 붕장어를 어획하는 통발 어구의 그물코 크기와 구멍의 직경은 각각 29.2mm, 18.6mm이상 되어야 한다.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1949-1957
• /
• 2003

A hybrid finite element analysis was used to analyze the influence of ring gear rim thickness and spline number on the static properties of a planetary gear system with manufacturing errors. Both of these parameters affected the bearing force and critical stress. The effect of changes in the rim thickness on the load sharing between the gears depended on the type of manufacturing error. Ring flexibility improved the load sharing between planetary gears only in systems with planet tooth thickness or planet tangential errors; for other types of error, ring flexibility worsened the load sharing. To improve load sharing, rim thickness and spline number should be controlled within a specific range. The minimum rim thickness limit should be determined considering not only the critical stress but also the load sharing. The effect of the ring gear boundary condition was more apparent in a system with errors than in a normal system.

• 한국기계가공학회지
• /
• 제19권7호
• /
• pp.60-66
• /
• 2020

In order to improve fatigue life of transmission gear carburizing is normally used. Carburizing is a very good process to achieve low cost and high performance. The machined gears are heated up to carburizing temperature and then cooled rapidly in an oil bath to produce high surface hardness. The gears may undergo excessive thermal distortion during heating and rapid cooling. In order to predict the distortion during heating and rapid cooling, a coupled thermo-mechanical simulation is needed. In the current research, the simulation of heating and cooling was performed. The results show that the thermal distortion and the residual stresses are well predicted by the coupled simulation. In addition, induction heating and rapid cooling simulation is carried out to predict the thermal distortion. The amount of distortion is compared. It is shown that induction heating is very effective to reduce thermal distortion.

• 드라이브 ㆍ 컨트롤
• /
• 제12권4호
• /
• pp.77-81
• /
• 2015

In general, the gears of mixer reducer for concrete mixer truck make use of the differential type planetary gear system to rotate mixer drum smoothly on the initial conditions. The planetary gear system is very important part of mixer reducer for concrete mixer truck because of strength problem. In the present study, calculating the gear specifications and analyzing the gear bending & compressive stresses of the differential planetary gear system for mixer reducer are necessary to analyze gear bending and compressive stresses confidently, for optimal design of the planetary gear system in respect to cost and reliability. As a result, analyzing actual gear bending and compressive stresses of the planetary gear system using Lewes & Hertz equation and verifying the calculated specifications of the planetary gear system, evaluate the results with the data of allowable bending and compressive stress from the Stress-No. of cycles curves of gears.

• Journal of Biosystems Engineering
• /
• 제25권6호
• /
• pp.445-456
• /
• 2000

A can type high-speed transplanting mechanism was developed. The mechanism consists of a cam and an epicycle gear train with one sun gear in the middle and four planet gears in a row but symmetric with respect to the sun gear. Two planting knives are pivoted on the two outer gears. When sun gear rotates with a constant velocity the planting knife rotates also with a constant velocity. This constant motion of the transplanting knife is accelerated partially by a cam fixed in the gear housing so that the locus of the planting knife becomes similar to that generated by a crank-type transplanting mechanism. This cam-type transplanting mechanism can solve the problems associated with the rotary-type transplanting mechanisms. The mechanism was designed with an aid of computer simulation and proved applicable to high speed transplanters by its mock-up model. The design process of the mechanism was presented and dynamic analysis was also carried out to show the advantages of the mechanism over the rotary type high-speed planting mechanism.