• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1635-1640
• /
• 2000

In this paper, a 18 GHz oscillator is designed with the push-push method an fabricated by semi-MMIC process, in which the second harmonic is the main output signal with the suppressed fundamental mode. In semi-MMIC process, passive components with microstrip transmission line are implemented using MMIC process on semi-insulating GaAs substrate. Then, chip types of P-HEMT, resistors, and capacitors are connected through Au wire-bonding. Also, the ground plane is inserted around the circuit and connected each other with the back-side of substrate through Au wire-bonding instead of via-hole. The semi-MMIC push-push oscillator shows the output powder of -10.5 dBm, the fundamental frequency suppression of -17.3 dBc/Hz, and the phase noise of -97.9 dBc/Hz at the offset frequency of 100 kHz.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.5
• /
• pp.462-473
• /
• 1999

This paper addresses the current measurement issue of all digital field oriented control of ac motors. The p paper focuses on the effect of low-pass filter and also on the sampling of the fundamental component of the m motor current. The low-pass filter, which suppresses the switching noise of the motor current, introduces v variable phase delay according to the current ripple frequency. It is shown that the current sampling error c consists of the fundamental component and high frL'quency ripple components. In this paper, the dependency of t this current sampling e$\pi$or on the reference voltage vector is investigated analytically and a sampling technique i is proposed to minimize the error. The work is based on the three phase symmetry pulse width modulation l inverter driving an induction machine. With this technique, the bandwidth of current regulator can be extended t to the limit given by the switching frequency of the inverter and more precise torque regulation is possible.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.23-30
• /
• 2014

This paper proposes a dead time compensation method for an AC motor drive using phase current polarity information which is detected based on a digital programmable low-pass filter (PLPF). The polarity detection using the PLPF is an alternative solution of a conventional method which uses a general low-pass filter (LPF) and hysteresis bands in order to avoid jittering due to noises. The PLPF not only adjusts its cutoff frequency according to the synchronous frequency of AC motors but also eliminates a gain attenuation and phase delay which are main problems of the general LPF. Through the PLPF, a fundamental component signal without gain and phase distortions is extracted from the measured raw current signal with noise. By use of the fundamental component, the polarity of current is effectively detected by reducing the hysteresis band. Finally, the proposed method compensates the dead time effects by adding or subtracting average voltage value to voltage references of the controller according to the detected current polarity information. The proposed compensation method is experimentally verified by compared with the conventional method.

• Structural Engineering and Mechanics
• /
• v.72 no.5
• /
• pp.541-555
• /
• 2019

Wind induced dynamic responses on hyperbolic cooling tower (HCT) shells are complicated functions of structure and wind properties, such as the fundamental frequency f_min, damping ratio ζ, wind velocity V, correlationship in meridian direction and so on, but comprehensions on the sensitivities of the dynamic responses to these four factors are still limited and disagree from each other. Following the dynamic calculation in time domain, features of dynamic effects were elaborated, focusing on the background and resonant components σ_B and σ_R, and their contributions to the total rms value σ_T. The σ_R is always less than σ_B when only the maximum σ_T along latitude is concerned and the contribution of σ_R to σ_T varies with responses and locations, but the σ_R couldn't be neglected for structural design. Then, parameters of the above four factors were artificially adjusted respectively and their influences on the gust responses were illustrated. The relationships of σ_R and the former three factors were expressed by fitted equations which shows certain differences from the existing equations. Moreover, a new strategy for wind tunnel tests aiming at surface pressures and the following dynamic calculations, which demands less experiment equipment, was proposed according to the influence from meridian correlationship.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.11
• /
• pp.1447-1454
• /
• 2018

In this paper, the design of robust DSC-PLL(Delayed Signal Cancellation Phase Locked Loop) is proposed for coping with frequency variation. This method shows significant performance for detection of fundamental positive sequence component voltage when the grid voltage is polluted by grid unbalance and frequency variation. The feedback frequency estimation of DSC-PLL is tracking the drift in the phase by unbalance and frequency variation. The robust DSC PLL is to present the analysis on method and performance under frequency variations. These compensation algorithms can correct for discrepancies of changing the frequency within maximum 193[ms] and improve traditional DSC-PLL. Linear interpolation method is adopted to reduce the discretized errors in the digital implementation of the PLL. For verification of robust characteristic, PLL methods are implemented on FPGA with a discrete fixed point based. The proposed method is validated by both Matlab/Simulink and experimental results based on FPGA(XC7Z030).

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.27-29
• /
• 2005

This paper studies particularly applicable method for sensorless Permanent Magnet Brushless DC(PMBLDC) Motor drive system. The waveform of the motor internal voltages (or back emf) contains a fundamental and higher order frequency harmonics. Therefore the third harmonics. component is extracted from the stator phase voltage. The resulting third harmonic signal keeps a constant phase relationship with the rotor flux for any motor speed and load condition. In addition, a simple starting method and a speed estimation approach are also proposed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.725-731
• /
• 2006

A novel design of frequency multiplier using a feedforward technique and a defected ground structure(DGS) is proposed. The feedforward loop in the proposed frequency multiplier suppresses the fundamental component $(f_0)$, the dumb-bell or spiral shaped DGS diminish unwanted harmonics such as second, third and fourth. Due to the combination of the feedforward structure and the DGS, only the multiplied frequency component$(2f_0,\;3f_0,\;4f_0)$ appears at the output port and the other unwanted components are suppressed excellently. The frequency multiplier is designed at 1 GHz $(f_0)$, by the proposed technique and measured. The measured output power of $2f_0,\;3f_0$ and $4f_0$ is -2.59 dBm, -5.36dBm and -4.57dBm, respectively, when the input power is 0dBm.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.225-231
• /
• 2013

This paper presents an improved signal processing technique in the square-wave-type voltage injection method for IPMSM sensorless drives. Since the sensorless method based on the square-wave voltage injection does not use low-pass filters to get an error signal for estimating rotor position and allows the frequency of the injected voltage signal to be high, the sensorless drive system may achieve an enhanced control bandwidth and reduced acoustic noise. However, this sensorless method still requires low-pass and band-pass filters to extract the fundamental component current and the injected frequency component current from the motor current, respectively. In this paper, these filters are replaced by simple arithmetic operations so that the time delay for estimating the rotor position can be effectively reduced to only one current sampling. Hence, the proposed technique can simplify its whole signal process for the IPMSM sensorless control using the square-wave-type voltage injection. The proposed technique is verified by the experiment on the 800W IPMSM drive system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.498-498
• /
• 2001

Seismic qualification of the Main Control Boards for nuclear power plants has been performed with the guideline of AS ME Section III. US NRC Reg. Guide and IEEE 344 code. The analysis model of the Main Control Boards is consist of beam. shell and mass element by using the finite element method. and, at the same time. the excitation forces and other operating loads for each model are encompassed with respect to different loading conditions. As the fundamental frequencies of the structure are found to be less than 33Hz. which is the upper frequency limit of the seismic load, the response spectrum analysis using ANSYS is performed in order to combine the modal stresses within the frequency limit. In order to confirm the structural and functional integrity of the major components, modal analysis theory is adopted to derive the required response spectrum at the component locations. As all the combined stresses obtained from the above procedures are less than allowable stresses and no mechanical or electrical failures are found from the seismic testing, it concludes the Main Control Boards is dynamically qualified for seismic conditions. Although the authors had confirmed the structural and functional integrity of both Main Control Boards and all the component, in this paper only the seismic analysis of the Main Control Board is introduced.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1500-1511
• /
• 2017

The purpose of this paper is to study a high-performance control scheme for neutral-point-clamping three-level (NPC-3L) inverter fed dual three-phase permanent magnet synchronous motor (PMSM) drives by considering some asymmetric factors such as the non-identical parameters in phase windings. To implement this, the system model is analyzed for dual three-phase PMSM drives with asymmetric factors based on the vector space decomposition (VSD) principle. Based on the equivalent circuits, PI controllers with feedforward compensation are used in the d-q subspace for regulating torque, where the cut-off frequency of the PI controllers are set at the twice the fundamental frequency for compensating both the additional DC component and the second order component caused by asymmetry. Meanwhile, proportional resonant (PR) controllers are proposed in the x-y subspace for suppressing the possible unbalanced currents in the phase windings. A dual three-phase space vector modulation (DT-SVM) is designed for the drive, and the balancing factor is designed based on the numerical fitting surface for balancing the DC link capacitor voltages. Experimental results are given to demonstrate the validity of the theoretical analysis and the proposed control scheme.