• 전력전자학회논문지
• /
• 제13권6호
• /
• pp.453-460
• /
• 2008

본 논문은 중용량에 적합한 새로운 이중출력 LLC 공진형 DC/DC 컨버터에 관한 것으로써, 별도의 Post-regulator및 추가되는 제어 IC 없이 정밀한 이중출력이 가능한 새로운 방식의 컨버터를 제안한다. 제안된 컨버터의 제어방식은 펄스폭 변조(PWM)와 동시에 주파수 변조(PFM)를 통해 이루어지며 Master 와 Slave 출력을 각각 주파수, 듀티로 제어함으로써 Slave 출력을 위한 별도의 Post-Regulator 및 제어 IC가 필요 없기 때문에, 저가의 컨버터 구현이 가능하다. 또한 기존 LLC 공진형 DC/DC 컨버터와 같이 스위칭 소자의 영전압 스위칭이 보장되는 동시에, Post-Regulator 로 인한 손실이 없기 때문에 효율 및 발열 특성이 매우 우수하다. 본 논문에서는 제안된 컨버터의 우수성과 신뢰성 검증을 위해, 실제로 50" FHD급 PDP용 전원회로를 위한 시뮬레이션 검토 및 시작품을 제작하고 이를 이용한 실험결과를 바탕으로 제안된 컨버터의 타당성을 검증한다.

• 한국산학기술학회논문지
• /
• 제14권6호
• /
• pp.2979-2984
• /
• 2013

본 논문은 도서지역에서 운용되고 있는 풍력-디젤 하이브리드 발전시스템의 풍속변화 등으로 인한 주파수변동 문제를 해결할 수 있는 플라이휘일 저장장치의 모델링 및 제어기 설계 방법을 제안하였다. 플라이휘일 저장장치는 효율측면에서 유리한 영구자석 동기기형 플라이휘일로 선정하여 모델링하였고, 주파수보상 제어기는 AC/DC/AC 양방향컨버터로 구성하되 동기기측 컨버터는 연계계통의 주파수변동에 대하여 충방전운전을 하도록 하고, 계통측 컨버터는 직류버스전압 일정제어를 통하여 출력을 하도록 설계하였다. 제안된 모델링 및 제어기 설계방법을 풍력-디젤 하이브리드 독립운전계통에 적용한 결과 풍속변화에 따른 주파수변동을 적정범위내로 유지할 수 있었다.

• IEIE Transactions on Smart Processing and Computing
• /
• 제4권3호
• /
• pp.189-193
• /
• 2015

This paper provides the design techniques of a successive approximation register (SAR) type 12b analog-to-digital converter (ADC) for distributed maximum power point tracking (DMPPT) control in a photovoltaic system. Both a top-plate sampling technique and a $V_{CM}$-based switching technique are applied to the 12b capacitor digital-to-analog converter (CDAC). With these techniques, we can implement a 12b SAR ADC with a 10b capacitor array digital-to-analog converter (DAC). To enhance the accuracy of the ADC, a single-to-differential converted DAC is exploited with the dual sampling technique during top-plate sampling. Simulation results show that the proposed ADC can achieve a signal-to-noise plus distortion ratio (SNDR) of 70.8dB, a spurious free dynamic range (SFDR) of 83.3dB and an effective number of bits (ENOB) of 11.5b with bipolar CMOS LDMOD (BCDMOS) $0.35{\mu}m$ technology. Total power consumption is 115uW under a supply voltage of 3.3V at a sampling frequency of 1.25MHz. And the figure of merit (FoM) is 32.68fJ/conversion-step.

• 대한전기학회논문지
• /
• 제35권12호
• /
• pp.541-554
• /
• 1986

This paper presents the results of driving performance analysis of permanent magnet synchronous motor using a microprocessor based control system. The system consists of three phase power transistor inverters, three phase controlled rectifier, three central processing units, and sensors. The three CPUs are, respectively, used to generate PWM control signals for the inverter generating three phase sine wave, to generate the gate control signals for firing the converter, and to supervise other two CPUs. The supervisor is used to compute PI control algtorithm to three phase reference sine wave for the inverter. It is also used to maintain a constant voltage frequency ratio for the converter operating as a constant torque controller. The inverter CPU retrieves precomputed PWM patterns from look up tables because of computation speed limitations found in almost available microprocessors. The converter CPU also retrieves precomputed gate control patterns from another look-up tables. For protecting the control ststem from any damage by extraordinary over currents, the supervisor receives the data from current sensor, CT, and break down the CB to isolate the circuits from source. A resolver has a good performance characteristics of overall speed range, especially on low speed range. Therefor the speed control accuracy is impoved. The microprocessor based PM synchronous motor control system, thus, has many advantages such as constant torque characteristics, improvement of wave, limitation on extraordinary over currents, improvement of speed control accuracy, and fast response speed control using multi-CPU and look-up tables.

• 전기전자학회논문지
• /
• 제16권4호
• /
• pp.335-342
• /
• 2012

본 논문에서는 고효율과 고역률을 위한 새로운 DCM-ZVS 스텝 업-다운 AC-DC 컨버터에 대해 연구된다. 제안한 DCM-ZVS 컨버터에 사용된 스위칭 소자들은 새로운 유사공진 회로에 의해 소프트 스위칭 기법으로 동작되고, 펄스폭변조(PWM) 방식에 의한 전류불연속모드(DCM)로 구동된다. 제안한 컨버터의 유사공진 회로는 스텝 업-다운 인덕터와 무손실 스너버 커패시터로 구성되고, 또한 DCM에 의해 제어회로 기법과 제어회로 구성이 간단한 장점이 주어진다. 입력 교류 전류파형은 일정 스위칭 주파수에 의한 교류 입력전압의 크기에 비례한 유사 정현파형으로 된다. 그 결과, 제안한 DCM-ZVS 컨버터는 낮은 스위칭 손실과 고효율을 얻을 수 있으며, 컨버터의 입력역률은 거의 단위역률로 된다. 해석적 결과의 타당성은 다양한 컴퓨터 시뮬레이션과 실험 결과를 통해 입증된다.

• 전력전자학회논문지
• /
• 제4권6호
• /
• pp.539-546
• /
• 1999

본 논문에서는 역률개선용 단일 수위치 부수투 플라이백 결합형 ZCS 준공진 컨버터(quasi-resonant converter(QRC))를 제안한다. 제안된 컨버터는 입력전류를 불연속 모드로 동작과 zero-crossing-point에서의 왜곡을 개선함으로써 고조파를 감소시켜 역률을 향상시켰으며 좋은 출력전압의 레귤레이션 성능을 가지고 있다. 또한 능동 클램프회로를 제안된 회로의 동작특성에 맞게 스위칭 시간을 조절해 줌으로써 ZCS-QR의 일잔적인 특성인 스위치 차단시의 스위치 양단전압의 공진현상을 제거하여 스위치의 전압스트레스를 줄였다. 체계적인 설계를 위하여 설계식을 제안하였으며 제안된 설계식을 통하여 프로토타입 컨버터를 설계하였다. 실험결과 효율은 약 87%, 역률은 약0.985이상을 얻었다. 따라서 본 컨버터는 스위칭 주파수가 수백kHz이상이고 높은 레귤레이션 성능을 요구하는 낮은 전압의 소용량 컨버터에 적합하다.

• Smart Structures and Systems
• /
• 제18권3호
• /
• pp.449-470
• /
• 2016

Energy harvesting is an emerging technique that extracts energy from surrounding environments to power low-power devices. For example, it can potentially provide sustainable energy for wireless sensing networks (WSNs) or structural control systems in civil engineering applications. This paper presents a comprehensive study on harvesting energy from earthquake-induced structural vibrations, which is typically of low frequency, to power WSNs. A macroscale pendulum-type electromagnetic harvester (MPEH) is proposed, analyzed and experimentally validated. The presented predictive model describes output power dependence with mass, efficiency and the power spectral density of base acceleration, providing a simple tool to estimate harvested energy. A series of shaking table tests in which a single-storey steel frame model equipped with a MPEH has been carried out under earthquake excitations. Three types of energy harvesting circuits, namely, a resistor circuit, a standard energy harvesting circuit (SEHC) and a voltage-mode controlled buck-boost converter were used for comparative study. In ideal cases, i.e., resistor circuit cases, the maximum electric energy of 8.72 J was harvested with the efficiency of 35.3%. In practical cases, the maximum electric energy of 4.67 J was extracted via the buck-boost converter under the same conditions. The predictive model on output power and harvested energy has been validated by the test data.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.777-783
• /
• 2010

In order to drive gas discharge lamps, DC-AC converters with a LCC resonant tank, whose output voltage is adjusted by a variable frequency control are frequently used. However, when they are activated by varying the operating frequency, converters are frequently damaged by unstable operation, due to the rising and falling of the operating frequency near the resonant frequency. To solve this problem, a simple protection circuit for the power supply of a gas discharge lamp is proposed in this paper. This circuit senses the primary current of the main transformer. Using this protection circuit, the operating frequency of the lamp driving inverter system is kept close to and on the right side of the resonant frequency and the inverter is always operated in the ZVS condition. The resulting stable variable frequency operation allows various gas discharge lamps to be tested without the risk of damaging the main switches, because the protection circuit can protect the power MOSFETs of bridge converters from abnormal conditions. The validity and effectiveness of the proposed protection circuit are verified through the experimental results.

• IEIE Transactions on Smart Processing and Computing
• /
• 제4권3호
• /
• pp.183-188
• /
• 2015

A 10-bit 10MS/s low power consumption successive approximation register (SAR) analog-to-digital converter (ADC) using a straightforward capacitive digital-to-analog converter (DAC) is presented in this paper. In the proposed capacitive DAC, switching is always straightforward, and its value is half of the peak-to-peak voltage in each step. Also the most significant bit (MSB) is decided without any switching power consumption. The application of the straightforward switching causes lower power consumption in the structure. The input is sampled at the bottom plate of the capacitor digital-to-analog converter (CDAC) as it provides better linearity and a higher effective number of bits. The comparator applies adaptive power control, which reduces the overall power consumption. The differential prototype SAR ADC was implemented with $0.18{\mu}m$ complementary metal-oxide semiconductor (CMOS) technology and achieves an effective number of bits (ENOB) of 9.49 at a sampling frequency of 10MS/s. The structure consumes 0.522mW from a 1.8V supply. Signal to noise-plus-distortion ratio (SNDR) and spurious free dynamic range (SFDR) are 59.5 dB and 67.1 dB and the figure of merit (FOM) is 95 fJ/conversion-step.

• 전력전자학회논문지
• /
• 제18권1호
• /
• pp.45-53
• /
• 2013

Fuel cell power system is one of the most promising energy source for the alternative energy because it has unique advantages such as high energy density, no power drop during operation, and feasible to make compact size. However, due to very low response time, fuel cell is difficult to correspond to drastic load changes and start-up operation. For solving these problem, fuel cell power system must include energy storage device such as Li-Poly battery or super capacitor. Therefore, bi-directional DC-DC converter must be required for this storage device and fuel cell-PCS control. This paper presents a design and modeling of the bi-directional DC/DC converter. Firstly, we present modeling the boost and buck mode of the bi-directional converter through both PWM switch model and state space averaging technique. Secondly, in order to minimize output ripple and transient response overshoot, we have two identical DC-DC converters interleaved and adopt two-loop voltage-current controller. The proposed bi-directional DC-DC converter's modeling method and control design have been verified with computer simulation and experimentation.