• 오토저널
• /
• 제13권6호
• /
• pp.109-118
• /
• 1991

In this study, it is intended to investigate the effect of the grinding conditions such as table feed, down feed, cross feed of residual stress distribution. And this distribution is investigated upon the grinding direction and the its orthogonal direction at ground layers. The material is used carbon steel (SM20C) which usually used to motor axis. And in order to be considered as Bernoulli-Euler beam, the dimension of the specimen is appropriately designed. According as corroiding the ground surface, the residual stress layers are removed and strain which occured on account of unbalance of internal stress is detected by rosette-gate. Through A/D converter and computer, these values are saved and evaluated residual stress by stress-strain relation formula. Finally, these results are diagrammatized with Auto Cad. The results obtained are as follows. As the depth from the ground surface increases in grinding direction and its orthogonal direction, tensile residual stress exists in the surface, and subsequently it becomes compressive residual stress as it goes downward. As the table feed, the cross feed and the down feed increase, maximum residual stress is transformed form the tensile to the compressive.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.179-184
• /
• 2008

This paper presents the design of the feed forward controller to improve on the non-interference control performance of a single PWM converter in parallel for high-speed trains. The feed forward controller is designed to minimize the interference generated by converter switching in parallel operation of PWM converters. The gain value of the feed forward controller is calculated by inductance values of the input transformer. However, it is difficult to decide this gain value exactly because inductance values are changed by the operation condition of an input transformer. In this paper, the proposed design of feed forward controller can exactly decide the gain value using the leakage inductances estimated by detecting the variation of input current. the validity of the proposed feed forward controller is proved through the simulation results.

• Membrane and Water Treatment
• /
• 제10권5호
• /
• pp.387-394
• /
• 2019

Membrane distillation (MD) is one of the water treatment processes which involves the momentum, heat and mass transfer through channels and membrane. In this study, CFD modeling has been used to simulate the heat and mass transfer in the direct contact membrane distillation (DCMD). Also, the effect of operating parameters on the water flux is investigated. The result shows a good agreement with the experimental result. Results indicated that, while feed temperature is increasing in the feed side, water flux improves in the permeate side. Since higher velocity leads to the higher mixing and turbulence in the feed channel, water flux rises due to this increase in the feed velocity. Moreover, results revealed that temperature polarization coefficient is rising as flow rate (velocity) increases and it is decreasing while the feed temperature increases. Lastly, the thermal efficiency of direct contact membrane distillation is defined, and results confirm that thermal efficiency improves while feed temperature increases. Also, flow rate increment results in enhancement of thermal efficiency.

• 풍력에너지저널
• /
• 제2권1호
• /
• pp.82-89
• /
• 2011

his dissertation is on power control system for MW-class wind turbine. Especially, the control purpose is reduction in electrical power and rotor speed. The base control structure is power curve tracking control using variable speed variable pitch operational type. For the reduction of fluctuations, more control algorithm is needed in above rated wind conditions. Because general pitch control system is low dynamic response as compared with the wind speed change. So, this paper introduces about the pitch feed forward control to minimize fluctuations of the electrical power and rotor speed. To maintain rated electrical power, the algorithm of feed forward control adds feed forward pitch amount to the pitch command of power curve tracking control. The effectiveness of the feed forward control is verified through the simulation.

• 멤브레인
• /
• 제14권2호
• /
• pp.157-165
• /
• 2004

막을 이용한 증기투과는 유기용제 및 휘발성 유기화합물의 제거와 관련되는 환경문제와 결부되어 활발한 연구가 진행되고 있다. 막을 이용한 휘발성 유기화합물 증기의 분리는 막 재질은 높은 온도에도 견딜 수 있어야 하고 증기에 대한 화학적 저항성도 매우 좋아야 한다. 증기투과에 가장 널리 쓰이고 있는 PDMS (polydimethylsiloxane)의 단점을 보완하기 위해 본 연구에서는 4,4'-diphenylmethane diisocyanate (MDI), PDMS 소프트 세그먼트를 기초로 한 polyurethane-polysiloxanes (PU/PDMS)를 합성하고 그들의 증기투과 특성을 연구하였다 각 Feed에 대한 팽윤도는 톨루엔 > 1,2-이염화에탄 > 헥산 순으로 나타났다. Feed의 농도가 증가할수록 톨루엔과 1,2-이염화에탄의 flux는 점차 증가하는 경향을 나타내었지만, 헥산은 feed의 농도가 증가하여도 flux의 변화가 나타나지 않았다. PU/PDMS 막은 VOCs와 상대적으로 높은 친화도를 가지고 있기 때문에 permeate에서의 농도는 50% 전후로 일정하게 나타났다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1603-1604
• /
• 2007

The load of power plants changes every from time to time according to which steam flow of boiler changes. the feed water control is very important for the power plant to be operated in its stability conditions. In case of circulation type boiler, the instability of feed water control leads to instability of drum level control. The higher level of drum water can induce bad quality steam to go into turbine which means the possibility of damage. The lower level of drum water can induce the tubes of boiler water wall to be overheated. In case of once through type boiler, the instability of feed water control leads to bad cooling of superheaters. The less the feed water flow is, the more heated the superheater is. It is necessary for the turbine driving feed water pump to be controlled for the optimal feed water flow in the large capacity power plant. The speed of turbine is controled for the feed water flow. By the way, the optimal control of steam valve is necessary for the speed control of turbine. Therefore, the various kinds of the steam valve structures are introduced in this paper

• 시스템엔지니어링학술지
• /
• 제10권1호
• /
• pp.1-15
• /
• 2014

Refinery plant producing petroleum products from crude oil has significantly contributed to the creation of the national interests as a leading engineering industries. However, domestic Engineering Procurement Construction (EPC) companies are facing heavy competition for orders. Domestic EPC companies as EPC contractors are faced with some problems such as undertaking responsibility for FEED packages produced by other FEED companies. But domestic EPC contractors are unfamiliar to development and validation of FEED packages. It causes poor profitability and lower competitiveness of domestic companies. It is necessary for domestic companies to have capability to perform FEED activities in order to overcome these limitations instead of focusing on EPC phase after FEED phase. The systematic procedure is needed to perform the FEED activities, however, there are present difficulties on it due to the lack of experience in FEED packages development which require various engineering knowledge of chemical process, mechanics, electrics, instrumentation, civil engineering. This study has applied systems engineering method which is multi-disciplinary approach to derive and verify the solution to meet the customer's needs when the complex system is developed to task execution process development of FEED activities for refinery plant. The problems that may occur in the future were identified in advance by taking into account the various stakeholders and system context through the application of systems engineering. It helps to develop the task execution process systematically. The developed task execution process of FEED activities is planned to make effectiveness verified by engineering professionals experienced in FEED and continually enhance this process by field application.

• 농업과학연구
• /
• 제44권1호
• /
• pp.86-94
• /
• 2017

In Korea, chemical analysis of animal feed is done through authorized feed analysis laboratories (AFALs). Analysis results among the AFALs need to be similar or within acceptable variations; however, there is no experimental evidence of their comparability. We aimed to determine the level of variation of feed chemical analysis results from different AFALs. For this, we requested analysis of four kinds of feed (corn, soybean meal, corn gluten feed, and ryegrass) to eight AFALs and the Cumberland Valley Analytical Services (CVAS) which is an internationally well-recognized feed analysis laboratory. The AFALs spent more time on analysis than did CVAS. Fiber analysis results varied significantly among laboratories. However, moisture, CP, and ash content values showed almost no variation. At least one AFAL obtained results with significant differences from CVAS for all tested values. These differences can be explained by the followings: 1) the standard methods for feed analysis (SMFA) established for AFALs are not detailed enough to control the analytical variations among different laboratories and 2) guidelines are insufficient for the quality control of analysis results in Korea. Failure to accurately identify the nutritional components of the feed could mean failure to provide adequate nutrients to the animals. Therefore, efforts to reduce the differences among AFALs, such as revising SMFA and publishing guidelines on quality control of feed analysis results, are important.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.536-542
• /
• 2002

There are two important variables in machining process control, which are feed and cutting speed. In this work, a two degree-of-freedom controller is designed and implemented to achieve on-line cutting force control and position control based on the modelling of cutting process dynamics which are established through step response test. Two schemes are proposed and implemented. The first is feed control under the constant spindle speed and spindle speed control under the constant feed speed. The second is a simultaneous control of feed and spindle speed. The last performs a position control under the constant cutting force. Those are confirmed to work properly. Especially the latter shows a faster response.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.195-198
• /
• 2000

It can be acquired the high effective productivity through of high speed, precision of machine tools, and then, machine tools will be got a competitive power. Industrially advanced countries already developed that the high speed feed is 60m/min using the high speed ball screw. Also, a lot of problems have happened the feed drive system. It is necessary to study about the characteristics of thermal deformation played a more critical role than static stiffness and dynamic rigidity in controlling the level of machining accuracy. In spite of the improving the thermal deformation characteristics of machine tools at the design stage, there are always some residual errors that have to be compensated for during machining. In this study, thermal deformation error automated compensation device with multiple linear regression is proposed that thermal deformation error can be eliminated at the machining stage. The developed device has been practically applied to the feed drive unit.