• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.718-720
• /
• 1999

This paper describes a charge pump PLL architecture which achieves high frequency operation and fast acquisition. This architecture employs multi-phase frequency detector comprised of precharge type phase frequency detector and conventional phase frequency detector. Operation frequency is increased by using precharge type phase frequency detector when the phase difference is small and acquisition time is shortened by using conventional phase frequency detector and increased charge pump current when the phase difference is large. By virtue of this multi-phase frequency detector structure, the maximum operating frequency of 694MHz at 3.0V and faster acquisition were achieved by simulation.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.4
• /
• pp.471-475
• /
• 1998

Phase shift spectroscopy is applied to Eu(Ⅲ) luminescence from $Eu^{3+}$-exchanged Y zeolite. The phase shift and intensity modulation of luminescence following intensity-modulated excitation are measured as a function of modulation frequency and they are fitted into a double exponential decay. The fast decay component, compared with the slow one, has narrower spectral bandwidth and is emitted from the $Eu^{3+}$ that has more polar and definite environment with higher symmetry and that interacts more easily with hydrated water molecules. The fast decay component is attributed to $Eu^{3+}$ at site Ⅱ' while the slow one to $Eu^{3+}$ at sites Ⅰ' and Ⅰ.

• Journal of Power Electronics
• /
• v.9 no.3
• /
• pp.507-515
• /
• 2009

This paper proposes an autonomous decentralized control for a parallel connected uninterruptible power supply (UPS) system based on a fast power detection method using a FPGA based hardware controller for a single phase system. Each UPS unit detects only its output voltage and current without communications signal exchange and a quasi dq transformation method is applied to detect the phase and amplitude of the output voltage and the output current for the single phase system. Fast power detection can be achieved based on a quasi dq transformation, which results in a realization of very fast transient response under rapid load change. In the proposed method, the entire control system is implemented in one FPGA chip. Complicated calculations are assigned to hardware calculation logic, and the parallel processing circuit makes it possible to realize minimized calculation time. Also, an Nios II CPU core is implemented in the same FPGA chip, and the software can be applied for non-time critical calculations. Applying this control system, an autonomous decentralized UPS system with very fast transient response is realized. Feasibility and stable operation are confirmed by means of an experimental setup with three UPSs connected in parallel. Also, rapid load change is applied and excellent performance of the system is confirmed in terms of transient response and stability.

• The Journal of Korean Academy of Prosthodontics
• /
• v.46 no.6
• /
• pp.639-643
• /
• 2008

STATEMENT OF PROBLEM: The degree of conversion may influence the ultimate mechanical and physical properties of provisional crown and fixed partial denture materials. The high levels of the unreacted residual monomer may cause deleterious effect on the properties. PURPOSE: The purpose of this study was to measure the degree of conversion of bis-acrylic based provisional crown and fixed partial denture materials by using an infrared spectroscopic method. MATERIAL AND METHODS: Chemically activated three bis-acrylic based provisional crown and fixed partial denture materials, LuxaTemp [DMG, Hamburg, Germany], fast set TemPhase [Kerr, Orange, CA, USA] and Protemp 3 Garant [3M-ESPE, St Paul, MN, USA], were investigated by Fourier transform infrared spectrometry (FTIR). The FTIR spectra of the materials tested were immediately obtained after mixing. The specimens were stored under dry conditions and at $23^{\circ}C$ for 24 hours, and then the spectra of the materials were also obtained. The degree of conversion (%) was calculated from the spectrum of the absorbance between the aliphatic double bond at 1637 $cm^{-1}$ and the aromatic double bond at 1608 $cm^{-1}$ using the baseline method. The data were statistically analyzed using one-way ANOVA and the multiple comparison Scheffe test at the significance level of 0.05. RESULTS: The mean value and standard deviation of the degree of conversion were 52.5 % ${\pm}$ 1.1 %, 50.3 % ${\pm}$ 0.8 %, and 42.3 % ${\pm}$ 4.9 % for LuxaTemp, Protemp 3 Garant and fast set TemPhase, respectively. There was no significant difference between LuxaTemp and Protemp 3 Garant, whereas there was a statistically difference between Protemp 3 Garant and fast set TemPhase, and LuxaTemp and fast set TemPhase (P < .05). CONCLUSION: The degree of conversion of fast set TemPhase was significantly lower than those of the others. The degree of conversion may be correlated with the rate of polymerization.

• Korean Journal of Applied Biomechanics
• /
• v.34 no.1
• /
• pp.25-33
• /
• 2024

Objective: The purpose of this study was to compare the lower extremity muscle activity and knee joint load according to movement speed conditions during the barbell back squat. Method: Nine males with resistance training experience participated in this study. Participants performed the barbell back squat in three conditions (Standard, Fast, and Slow) differing movement speed. During the barbell back squat, muscle activity of the rectus femoris (RF), vastus lateralis (VL), vastus medialis (VM), biceps femoris long head (BFL), semitendinosus (ST), gluteus maximus (GM), gastrocnemius (GCN), and tibialis anterior (TA) was collected using an 8 channel wireless EMG system. The peak flexion angle of the lower extremity joints and the peak resultant joint force in each direction of the knee joint were calculated using eight motion capture cameras and ground reaction force plates. This study was to used the Friedman test and the Wilcoxon signed rank test, to compare lower extremity muscle activity and peak resultant joint force at knee joint according to movement speed conditions during the barbell back squat, and the statistical significance level was set at .01. Results: In the downward phase of the barbell back squat, the RF and TA showed the higher muscle activity in the fast condition, and in the upward phase, RF, VL, VM, BFL, ST, GM, and TA showed the higher muscle activity in the fast condition. As a results, analyzing of the load on the knee joint, in the downward phase, and in the upward phase, the higher peak compressive force of the knee joint was showed in the fast condition. Conclusion: The barbell back squat with fast movement speed was more effective due to increased muscle activity of lower extremity, but one must be careful of knee joint injuries because the load on the knee joint may increase during the barbell back squat with fast movement speed.

• Proceedings of the IEEK Conference
• /
• 2001.06c
• /
• pp.145-148
• /
• 2001

This paper presents a phase-based stereo matching algorithm in order to efficiently extract 3-dimensional objects from two 2D images. Conventional phase-based methods, especially using windowed Fourier phases, inherit good properties in the cage of hierarchical approaches, because they basically use a multi-resolution phase map. On the contrary, their computational cost is too heavy. Therefore, a fast hierarchical approach, using multi-resolution phase-based strategy and reducing redundancies of phase calculations based on FFT concept is proposed in this paper. In addition, a structural matching algorithm on the phase domain is presented to improve the matching quality. In experimental results. it is shown that the computation loads are considerably reduced about 8 times and stable outputs are obtained from various images.

• The Bulletin of The Korean Astronomical Society
• /
• v.35 no.1
• /
• pp.43.2-43.2
• /
• 2010

Following the success of detecting fringes on KVN (Korean VLBI Network), a phase referencing observation is currently planned in order to achieve a better sensitivity in mm-VLBI. The high frequency observation ($\geq$ 22 GHz), wide bandwidths (~512 MHz) and high speed data recording (~1 Gbps, Mark5B) will result in resolution and sensitivity improvement on KVN. In particular, two powerful techniques of VLBI phase correction by fast-antenna switching and multi-frequency phase referencing are also introduced in KVN, hoping to resolve the problem of atmospheric delay errors which degrade the coherence significantly. In this study, we have compared the expected performance of phase referencing between fast antenna switching and multi-frequency phase referencing and discussed the essential condition and postulates of phase referencing for KVN.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.82-87
• /
• 2008

This paper presents a new fast locking dual-slope phase-locked loop. The conventional dual-slope phase-locked loop consists of two charge pumps and two phase-frequency detectors. In this paper, the dual-slope phase-locked loop was achieved with a charge pump and a phase-frequency detector as adjusting a current of the charge pump according to the phase difference. The proposed circuit was verified by HSPICE simulation with a $0.35{\mu}m$ CMOS standard process parameter. The phase locking time of the proposed dual-slope phase-locked loop was $2.2{\mu}s$ and that of the single-slope phase-locke loop was $7{\mu}s$.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.1
• /
• pp.83-98
• /
• 2004

The purpose of this study was to determine the kinematic variables of the hurdling for a korea record holder (A) and a national hurdle representative (B). after the kinematic variables such the distance and the distance and height of C.G, the velocity and the angle were analyzed about the hurdling. The results were summarized as follows; 1. In terms of the distance and the height of C.G, subject A showed long in horizontal distance from C.G to the take-off phase, but showed short in the landing phase. Subject B showed short in horizontal distance from C.G to the take-off phase, and showed long in the landing phase. 2. In terms of the velocity of C.G, Subject A showed fast C.G velocity in horizontal direction to the braking phase, Subject A and B showed slower C.G velority in the landing phase, but Subject A showed height C.G velocity in vertical direction to the to the take-off, the landing, and propulsion phase 3. In terms of the angle of C.G and lean of C.G to front at the braking and the take-off phase. Subject A kept the less angle in the maximum trunk lean to front at the flight phase as comparison with Subject B. 4. In terms of the velocity of the knee and the ankle joint. Subject A showed fast in the resultant velocity of the left ankle joint the take-off phase, but showed slow in the left knee joint. Subject B showed fast in the resultant velocity of the left knee joint the take-off phase, but showed slow in the right knee and the right ankle joint.

• Journal of information and communication convergence engineering
• /
• v.3 no.1
• /
• pp.18-22
• /
• 2005

This paper presents the analog adaptive phase-locked loop (PLL) architecture with a new adaptive bandwidth controller to reduce locking time and minimize jitter in PLL output for wireless communication. It adaptively controls the loop bandwidth according to the locking status. When the phase error is large, the PLL increases the loop bandwidth and reduces locking time. When the phase error is small, the PLL decreases the loop bandwidth and minimizes output jitters. The adaptive bandwidth control is implemented by controlling charge pump current depending on the locking status. A 1.28-GHz CMOS phase-locked loop with adaptive bandwidth control is designed with 0.35 $mu$m CMOS technology. It is simulated by HSPICE and achieves the primary reference sidebands at the output of the VCO are approximately -80dBc.